Pioneer VSX-90TXV operating instructions Video, Settings

Page 68

12Additional information

Symptom

Remedy

Can’t record audio.

• You can only make a digital recording from a digital source, and an analog recording from an analog

 

source.

 

• For digital sources, make sure that what you’re recording isn’t copy protected.

 

• Check that the OUT jacks are properly connected to the recorders input jacks (see Connecting analog

 

audio sources on page 17).

 

 

Subwoofer output is very low.

• To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL (see Speaker

 

Setting on page 40).

 

 

Everything seems to be set up

• The speakers may be out of phase. Check that the positive/negative speaker terminals on the receiver are

correctly, but the playback sound

matched with the corresponding terminals on the speakers (see Connecting the speakers on page 18).

is odd.

 

 

 

The PHASE CONTROL feature

• If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is set to

doesn’t seem to have an audible

the highest frequency setting. If there is a PHASE setting on your subwoofer, set it to 0º (or depending on

effect.

the subwoofer, the setting where you think it has the best overall effect on the sound).

 

• Make sure the speaker distance setting is correct for all speakers (see Speaker Distance on page 42).

 

 

Noise or hum can be heard even

• Check that personal computers or other digital components connected to the same power source are not

when there is no sound being

causing interference.

input.

 

 

 

There seems to be a time lag

• See Automatically setting up for surround sound (Auto MCACC) on page 8 to set up your system again

between the speakers and the

using MCACC (this will automatically compensate for a delay in the subwoofer output).

output of the subwoofer.

 

 

 

The maximum volume available

• This is not a malfunction. If the levels in Channel Level on page 41 have been adjusted, the maximum

(shown in the front panel display)

volume will change accordingly.

is lower than the +12dB

 

maximum.

 

 

 

Video

Symptom

Remedy

No image is output when an input

• Check the video connections of the source component (see page 14).

is selected.

• Make sure the input assignment is correct for components connected using component cables (see The

 

Input Assign menu on page 55).

 

• Check the video output settings of the source component.

 

• Check that the video input you selected on your TV is correct.

 

• When the source component is connected to this receiver with a component video cable, you must also

 

connect your TV to this receiver with a component video cable.

 

 

Can’t record video.

• Check that the source is not copy-protected.

 

• The video converter is not available when making recordings. Check that the same type of video cable is

 

used for connecting both the recorder and the video source (the one you want to record) to this receiver.

 

 

Noisy, intermittent, or distorted

• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the video

picture.

quality may just be poor (with some video game units, for example). The picture quality may also depend on

 

the settings, etc. of your display device. Switch off the video converter and reconnect the source and display

 

device using the same type of connection (component, S-video or composite), then start playback again.

 

 

Settings

Symptom

Remedy

The Auto MCACC Setup

• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see also

continually shows an error.

Problems when using the Auto MCACC Setup on page 10). If the noise level cannot be kept low enough, you

 

will have to set up the surround sound manually (page 36).

 

 

After using the Auto MCACC

• There may have been some low frequency noise in the room from an air-conditioner, motor, etc. Switch

Setup, the speaker size setting is

off all other appliances in the room and use Auto MCACC Setup again.

incorrect.

• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some cases.

 

You can change the speaker setting manually in Speaker Setting on page 40 if this is a recurring problem.

 

 

68

En

Page 67 Page 69
Image 68
Page 67 Page 69
Contents VSX-90TXV Federal Communications Commission Declaration of Conformity Model NumberPhone Keep in a Secure AREA. this is for Your SecurityImportant Safety Instructions Contents Using other functions Other SettingsOther connections Controlling the rest of your systemBefore you start Chapter FeaturesBefore you start Installing the receiver When installing this unit, make sure to leave spaceBefore you start Checking what’s in the box VentilationAutomatically setting up for surround sound Auto Mcacc Minute guide02 5 minute guide Chapter Introduction to home theaterMinute guide Follow the instructions on-screenBetter sound using Phase Control Problems when using the Auto Mcacc Setup02 5 minute guide Playing a sourceRear panel Connecting your equipmentConnecting your equipment Chapter About the video converter Connecting your equipmentWhen making cable connections Connect using a stereo RCA/phono jack cable Use a coaxial cable designed for digital audio342 DVD playerDVR, VCR, etc Connecting a DVD/HDD recorder, VCR and other video sourcesUsing the component video jacks On an HDMI-compatible monitor.1 Connecting using HdmiUse a three-way component video cable CD-R, MD, DAT, etc Connecting digital audio sourcesAbout Hdmi Connecting analog audio sources Connecting a component to the front panel inputsAbout the WMA9 Pro decoder Tape deck, etcConnecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersBanana plug connections 10 mm 3/8Connecting antennas THX speaker system setupConnecting external antennas Plugging in the receiverAC outlet Out before unpluggingFront panel Controls and displaysControls and displays Chapter Operating range of remote control unit Controls and displaysControls and displays Display Controls and displays Remote control RECEIVERInput Select SelectMulti OPE ShiftSOURCE ReceiverListening to your system Listening to your system ChapterListening in surround sound Auto playbackUsing the Home THX modes Using the Advanced surround effectsTHX Games Mode Listening to your systemUsing Front Stage Surround Advance Setting the effect optionsPress EFFECT/CH SEL again to adjust other settings Setting What it does OptionsListening to your system Using Stream Direct Choosing the input signalUsing surround back channel processing Listening with Acoustic Calibration EQUsing the Virtual Surround Back mode Listening to your system Using Midnight and Loudness Using the Sound RetrieverUsing the tone controls Press Tone to select the frequency you want to adjustUsing the tuner Using the tuner ChapterSaving station presets Listening to the radioUsing the tuner Naming station presetsListening to station presets AbcdefghijklmnopqrstuvwxyzSystem Setup menu System Setup menu ChapterMaking receiver settings from the System Setup menu Surround back speaker settingSystem Setup menu Manual Mcacc setupSelect ‘Manual MCACC’ from the System Setup menu Select ‘Fine Ch Level’ from the Manual Mcacc setup menuSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Volume increases to the reference levelFine Speaker Distance Professional Acoustic Calibration EQSetting the Acoustic Calibration EQ automatically Copying your Acoustic Calibration EQ settingsFront Align Setting the Acoustic Calibration EQ manuallyChecking your Acoustic Calibration EQ settings Select ‘Manual SP Setup’ then press Enter System Setup menu Manual speaker setupSpeaker Setting Crossover Network Channel LevelSpeaker Distance THX Audio SettingTHX Speaker Setup Connecting an iPod Connecting your iPod to the receiverOther connections Other connections ChapterUsing XM Radio Connecting your XM Radio receiverWatching photos and video content Other connectionsUsing XM HD Surround Saving channel presetsListening to XM Radio Selecting channels and browsing by genreUsing Sirius Radio Connecting your Sirius Connect TunerUsing the XM Menu Listening to channel presetsUsing the Sirius Menu Press Sirius SHIFT+TV to switch to the Sirius inputSirius Menu provides additional Sirius Radio features Listening to Sirius RadioConnecting the multichannel analog inputs Speaker B setupSwitching the speaker system Selecting the multichannel analog inputsConnect your speakers as shown below Bi-wiring your speakersBi-amping your front speakers Other connections Connecting additional amplifiers Basic MULTI-ZONE setupMULTI-ZONE listening Making MULTI-ZONE connectionsMULTI-ZONE remote controls Using the MULTI-ZONE controlsSurround Back System MULTI-ZONE setup Remote sensor on the front panel of this receiver.1 Other connections Connecting an IR receiverSwitching components on and off using the 12 volt trigger Audio DVD playerTV/SAT SR+ Dimmer Other Settings Other Settings ChapterInput Assign menu Assigning the digital inputsOther Settings Other Setup menuDynamic Range Control Setup Assigning the Hdmi inputsDual Mono Setup LFE Attenuator SetupSR+ Setup for Pioneer plasma displays Video Converter SetupMulti Zone Setup Volt Trigger setupUsing other functions Using other functions ChapterReducing the level of an analog signal Using the sleep timerUsing other functions Dimming the display Switching the speaker impedanceResetting the system Press System Setup to confirmControlling the rest of your system Select the button for the command you want to input Controlling the rest of your systemMulti Operation and System Off Programming a multi-operation or a shutdown sequenceUsing multi operations Using System offControls for TVs Buttons Function ComponentsFunction Components MD/CD-R/ DVRDecide which component you want to use the remote sensor Troubleshooting PowerAdditional information Additional information ChapterAdditional information Other audio problemsSymptomRemedy Settings VideoDisplay Assign menu onIPod messages Remote controlSymptom Cause Action XM radio messages Sirius radio messagesAdditional information Surround sound formats DolbyAbout THX Windows MediaTM Audio 9 ProfessionalListening modes with different input signal formats Stereo 2 channel signal formatsStandard Auto SurroundMultichannel signal formats Input signal format StandardAdditional information Specifications Cleaning the unitDecibel Level Example To establish a safe levelOnce you have established a comfortable sound level Pioneer Corporation

VSX-90TXV specifications

The Pioneer VSX-90TXV is a powerhouse of a receiver that caters to the most discerning audiophiles and home theater enthusiasts. With its robust build and an impressive array of features, this model stands out as a staple in the Pioneer lineup, making it a noteworthy option for anyone looking to enhance their audio experience.

One of the most significant features of the VSX-90TXV is its impressive multi-channel amplification. It offers a powerful output of 135 watts per channel at 8 ohms, ensuring that even the most demanding audio signals are handled with ease. This receiver supports a variety of configurations, including 7.1 channel surround sound, delivering an immersive audio environment that brings movies, music, and gaming to life.

The VSX-90TXV is equipped with advanced surround sound technologies. It supports Dolby TrueHD and DTS-HD Master Audio formats, providing lossless audio that retains the original quality of recordings. The inclusion of Pioneer's proprietary MCACC (Multi-Channel Acoustic Calibration System) allows users to optimize their speaker setup for any room, by analyzing and adjusting the acoustics to provide the best possible sound.

Connectivity is another strong suit of the VSX-90TXV. It features multiple HDMI inputs, allowing for a hassle-free connection to various devices. With support for 4K Ultra HD pass-through and HDR (High Dynamic Range), it ensures that users can enjoy high-quality video along with high-fidelity audio. Additionally, there are plenty of analog and digital inputs for versatility with other audio sources.

Another remarkable aspect of the VSX-90TXV is its compatibility with wireless technologies, including Bluetooth and Wi-Fi. This allows for effortless streaming from a variety of devices, making it simple to enjoy music from smartphones, tablets, and computers. Pioneer's proprietary FireConnect technology also facilitates multi-room audio, allowing music to be played throughout the home in different zones.

Design-wise, the receiver features a sleek, modern aesthetic that blends seamlessly into any home entertainment setup. The intuitive interface and remote control make navigation simple, ensuring that users can easily access all the receiver’s features.

In summary, the Pioneer VSX-90TXV combines powerful amplification, advanced surround sound technology, and versatile connectivity options, making it an ideal choice for anyone looking to elevate their home audio experience. Whether it’s for cinematic thrills or soulful music sessions, this receiver delivers on all fronts.
Top Page Image Contents