Hughes & Kettner Standard SETUP/CABLE Connections Triamp MK II Operation, Channel Selection

Page 9

TRIAMP MK II - MANUAL

3.0 STANDARD SETUP/CABLE CONNECTIONS

4.0 TRIAMP MK II OPERATION

4.1 CHANNEL SELECTION

The TriAmp® MK II’s six fundamental sounds may be accessed via the channel selector buttons on the front panel or the TriAmp® MK II Stageboard are called up.

You can also execute switching functions via MIDI using the MSM 1 MIDI Module (refer to Section 4.4). If you want to use an external MIDI switcher, you will need to make an adapter cable that acces- ses the Stageboard jack, wiring it according to the pin assignments shown in Diagram below. Channel selection is executed via momentary contact; FX LOOP activation is executed by switching, namely by applying pin 8 to pin 5 (gro- und).

Stageboard jack pin assignments:

4.2TRIAMP® MK II AND SIGNAL PROCESSORS

The TriAmp® MK II is equipped with a variable effects loop (serial/parallel). In parallel mode, the effect signal is added to the original preamp signal so that you can dial in a setting where the dry signal remains audible during the brief delays that multieffector switching is prone to cause.

This face-saving feature prevents glaringly evident and potentially embarrassing sonic drop-out the LEVEL knob controls the mix. The passive nature of the mix guarantees that the original signal is not sent through any solid-state circuitry. When the FX LOOP is deactivated, the buffer stage for the effects side is switched off via a relay, thereby ensuring that the FX LOOP never compromises the amp's sound quality.

NOTE:

Ground/Masse

Amp 3A

Amp 3B

FX-LOOP

Amp 2B

Amp 2A

Amp 1B

Amp 1A

As a rule of thumb, the best method for using sig- nal processors is to set the output of the processor itself to maximum effect (balance = 100%), and then mix the processed signal with the original signal via the LEVEL control to avoid the sound

ENGLISH

+ 22 V Output

degradation an effects device might otherwise introduce. Switch the FX LOOP button on the front panel to OFF if you want to switch the FX LOOP via the Stageboard or MIDI commands.

9

Image 9
Contents Watt Tube Amplifier Wichtig Thank YOU for Choosing the Triamp MK Before Powering UP ContentsThree Amps in the Triamp MK AMP 2 Classic British Drive AMP 1 Chunky Clean + FAT Drive CleanAMP 3 Modern Gain Connections and Control FeaturesFront Overview of Control FeaturesPreamp Section Master SectionFX Loop RearTriamp MK II and Signal Processors Standard SETUP/CABLE Connections Triamp MK II OperationChannel Selection Stageboard jack pin assignmentsRED BOX DI OUT ALL-TUBE Tone to the Mixer Connecting signal processorsTriamp MK II and Midi Installing the MSM-1 Midi ModuleWhat should you keep in mind When you’re replacing tubes? When is it a good idea To replace tubes?How can you extend the service life Tubes? Troubleshooting Deutsch Dreizehn Röhren FÜR DEN Guten TON VOR DER InbetriebnahmeInhalt AMP 1 Chunky Clean + FAT Drive Clean Netzanschluss UND Wahl DER Netzspannung Anschlüsse UND BedienelementeVorderseite Übersicht DER BedienelementePreamp Sektion Master SektionRückseite DAS Anwählen DER Kanäle Standard SET UP/VERKABELUNG Bedienung DES Triamp MKDER Triamp MK II MIT Effektgeräten Pinbelegung der StageboardbuchseAnschluss DES Effektgerätes RED BOX DI OUT Vollröhre AM MischpultDER Triamp UND Midi Installation des MSM-1 MIDI-ModulsRÖHRENTAUSCH, Wartung UND Pflege Wann ist ein Röhrentausch sinnvoll?Was ist beim Röhrentausch Zu beachten? Wie kann man die Lebensdauer Von Röhren verlängern? FEHLERBESEITIGUNG/TROUBLESHOOTING Der TriAmp MK II lässt sich Nicht einschaltenDer Effektweg ist ungewollt aktiv Technische Daten General DataAllgemeines Hughes & Kettner Triamp MK United states Deutsch English Francais Italiano Español To find a local distributor please visit