Hughes & Kettner MK II manual Rear, FX Loop

Page 8

TRIAMP MK II - MANUAL

REAR

MAINS IN: Socket for the included Euromains power cable. Before plugging into the wall socket, make certain the amp's voltage rating as dis- played in the VOLTAGE SELECTOR window matches your local AC voltage rating.

VOLTAGE SELECTOR: If you need to change TriAmp® MK II's voltage to your local AC voltage rating, pull out this cartridge and see Section 2.1 for further details.

ANODE FUSE: Fuse holder for the power amp's anode fuses. Be sure you only use fuses rated to the indicated specifications.

HALF POWER: This power soak switch cuts the TriAmp® MK II’s output power in half from 100 watts to 50 watts.

PREAMP OUT, POWER AMP IN: The TriAmp® MK II sports an ancillary serial FX loop that lets you control master volume via a volume pedal.

The preamp signal is patched out via PREAMP OUT jack and in again via POWER AMP In.

STAGEBOARD: Input jack for TriAmp® MK II STAGEBOARD. The length of the cord can be extended using standard computer cables (equipped with 9-pin SUB-D connector).

FX LOOP

FX SERIAL/PARALLEL: An innovative new feature of the TriAmp® MK II, it lets you select the desired type of effects loop, parallel or serial, at the touch of a button. The FX loop setting may be stored and switched via MIDI using the optional MSM-1 MIDI module.

LEVEL: Determines the relative levels of the TriAmp® MK II’s preamp signal and the signal routed into the FX RETURN jack as sent from a connected effects device and the like. In other words, use it to set the desired wet/dry mix.

FX SEND: Connect this jack to your effects processor's input jack.

FX SEND LEVEL: This damping switch allows you to adapt the signal level to lower-level effects devices. Press this switch in for instrument level processors (e.g. stomp boxes).

FX RETURN: Connect this jack to your effects processor's output jack.

RED BOX® DI OUT: This is a balanced output featuring the RED BOX® Cabinet Simulator.

It enables you to feed the TriAmp® MK II signal directly to a mixing console for stage and recording purposes. Refer to Section 4.3 for details.

SPEAKER: The TriAmp® MK II features 4-, 8- and 16-ohm speaker outs for perfect impedance matching. Its minimum impedance is 4 ohms.

NOTE:

Never operate the TriAmp® MK II without a loudspeaker connected!

8

Image 8
Contents Watt Tube Amplifier Wichtig Thank YOU for Choosing the Triamp MK Three Amps in the Triamp MK Before Powering UPContents AMP 1 Chunky Clean + FAT Drive Clean AMP 2 Classic British DriveConnections and Control Features AMP 3 Modern GainOverview of Control Features FrontPreamp Section Master SectionRear FX LoopStandard SETUP/CABLE Connections Triamp MK II Operation Triamp MK II and Signal ProcessorsChannel Selection Stageboard jack pin assignmentsConnecting signal processors RED BOX DI OUT ALL-TUBE Tone to the MixerInstalling the MSM-1 Midi Module Triamp MK II and MidiWhen is it a good idea To replace tubes? What should you keep in mind When you’re replacing tubes?How can you extend the service life Tubes? Troubleshooting Deutsch Inhalt Dreizehn Röhren FÜR DEN Guten TONVOR DER Inbetriebnahme AMP 1 Chunky Clean + FAT Drive Clean Anschlüsse UND Bedienelemente Netzanschluss UND Wahl DER NetzspannungÜbersicht DER Bedienelemente VorderseitePreamp Sektion Master SektionRückseite Standard SET UP/VERKABELUNG Bedienung DES Triamp MK DAS Anwählen DER KanäleDER Triamp MK II MIT Effektgeräten Pinbelegung der StageboardbuchseRED BOX DI OUT Vollröhre AM Mischpult Anschluss DES EffektgerätesInstallation des MSM-1 MIDI-Moduls DER Triamp UND MidiWas ist beim Röhrentausch Zu beachten? RÖHRENTAUSCH, Wartung UND PflegeWann ist ein Röhrentausch sinnvoll? Wie kann man die Lebensdauer Von Röhren verlängern? Der Effektweg ist ungewollt aktiv FEHLERBESEITIGUNG/TROUBLESHOOTINGDer TriAmp MK II lässt sich Nicht einschalten Allgemeines Technische DatenGeneral Data Hughes & Kettner Triamp MK United states Deutsch English Francais Italiano Español To find a local distributor please visit