Pioneer VSX-47TX manual Auto All speakers are set automatically. The remote, Use this setting

				Setting Up for Surround Sound
2	3.1. Speaker Systems			AUTO : All speakers are set automatically. (The remote
				control must be hooked up to the front panel in order to
	[	Manual Free	]
				use this setting.)
		[Manual THX]

(all small)

[Auto]

[Return]

3,4	2.1. Speaker				Systems
				Manual Free
		Speaker System Select
		[								]
			Normal		Surround
		(	Next)
5,6	2.1. Speaker				Systems
				Manual Free
	”	Normal Surround ”
		Front				[					]
							LARGE
		Center					[LARGE]
		Surround				[LARGE]
		SurrBack				[LARGEX2]
		Subwoofer				[ YES					]
		(	NEXT)
7	2.1. Speaker				Systems
				Manual Free
	”	Normal Surround ”
		Front				[LARGE]
		Center				[LARGE]
		Surround				[LARGE]
		SurrBack				[LARGEX2 ]
		Subwoofer				[		YES			]
		(	NEXT)
9	3.1. Speaker				Systems
				Manual Free
	< Front Bi-Amp (5.1) >
		Crossover			[				]
							80Hz
	Normal			Surround
			(THX	Speaker = 80Hz)
		Speaker B [				Bi-Amp					]

For MANUAL FREE, select it and press ENTER. Then go to step 3.

For MANUAL THX, select it and press ENTER. Then go to step 3.

For AUTO, select it and press ENTER. Be prepared for loud test tones and make sure the room is free of ambient noise (see memo page 15). When you see OK on the OSD the setup is finished. Go to step 9.

3Use the 2 3 buttons to select either

NORMAL SURROUND or FRONT BI-

AMP (5.1).

NORMAL SURROUND: For normal home theater use

FRONT BI-AMP (5.1): Settings for bi-amp (see p.70).

4Use the ∞ button to go to the next screen.

5With the 5∞ buttons choose the set of

speakers that you want to set.

If you selected MANUAL THX in step 2 set all speakers, except for surround back, to SMALL.

6Use the 2 3 buttons to choose the size and number for each set of speakers as well as LARGE, SMALL, YES, NO or PLUS.

7Repeat steps 5 & 6 for all speakers channels.

SURROUND SET UP

[Return]

10	2.1. Speaker		Systems
		Manual Free
	” Normal Surround ”
	Crossover		[ 80Hz ]
	Normal	Surround
	(THX	Speaker = 80Hz)

Speaker B : Secound Zone

[Return]

memo

If you have a subwoofer and like lots of bass, it may seem logical to select LARGE for your front speakers and leave the subwoofer selected. This may not, however, yield the best bass results. Depending on the size and shape of your room you may actually experience a decrease in the amount of bass due to what is called "low frequency cancellations." If you have a subwoofer, listen to the bass response with the front speakers set to LARGE and SMALL alternatively and let your ears judge which sounds best.

If you have a subwoofer, the safest option is to route all the bass sounds to it by selecting SMALL for the front speakers.

8Use the ∞ button to go to the next screen.

9Use the 2 3 buttons to choose a

Crossover Frequency of 50 Hz, 80 Hz,

100 Hz, 150 Hz or 200 Hz.

Certain bass sounds will play back from the subwoofer if you selected it as YES (or PLUS), or from the front speakers if you selected them as LARGE.

This setting decides where the cutoff will be between those bass sounds playing back from the speaker selected as above and the bass sounds for the entire soundtrack, which play back from all speakers used. If you selected MANUAL THX in step 2 the crossover frequency is fixed at 80kHz and this screen does not appear.

10 Use the 5∞ buttons to select RETURN and press ENTER.

Next, proceed to CHANNEL DELA Y below.

If you want to change a setting before proceeding

start over from step 1.

37