Pioneer VSX1017TXV manual Connecting the multichannel analog inputs, Speaker B setup

Page 48

08Other connections

•Antenna Aiming – Check the strength of satellite and terrestrial reception.

•Password Set – Set the parental lock password.

3When you’re finished press TOP MENU to return to the reception display.

Connecting the multichannel analog inputs

For DVD Audio and SACD playback, your DVD player may have 5.1, 6.1 or 7.1 channel analog outputs (depending on whether your player supports surround back

channels).1 Make sure that the player is set to output multichannel analog audio.

1Connect the front, surround, center and subwoofer outputs on your DVD player to the corresponding MULTI CH input jack on this receiver.

•Use standard RCA/phono jack cables for the connections.

2If your DVD player also has outputs for surround back channels, connect these to the corresponding MULTI CH input jacks on this receiver.

•Use standard RCA/phono jack cables for the connections.

•If there is a single surround back output, connect it to the SURROUND BACK L (Single) jack on this receiver.

Selecting the multichannel analog inputs

If you have connected a decoder or a DVD player as above, you must select the analog multichannel inputs

for surround sound playback.2

1Make sure you have set the playback source to the proper output setting.

For example, you might need to set your DVD player to output multichannel analog audio.

2Press MULTI CH IN (front panel).

•Depending on the DVD player you’re using, the analog output level of the subwoofer channel may be too low. In this case switch the receiver into standby, then press STANDBY/ON while holding down SBch PROCESSING on the front panel. This switches between SW IN +10dB (increase of 10 decibels) and SW IN 0dB (default) in the subwoofer channel.

Speaker B setup

Caution

•Before making or changing the connections, switch off the power and disconnect the power cord from the power outlet. Plugging in components should be the last connection you make with your system.

•Be careful not to allow any contact between speaker wires from different terminals.

•You can use speakers with a nominal impedance between 6 Ω to 16 Ω (please see Switching the speaker impedance on page 56 if you plan to use speakers with an impedance of less than 8 Ω).

After selecting Speaker B in Surround back speaker setting on page 35, you can use the speakers connected to the (surround back) B speaker terminals on the rear panel to listen to stereo playback in another room. See Switching the speaker system below for the listening options with this setup.

1Connect a pair of speakers to the surround back speaker terminals on the rear panel.

Connect them the same way you connected your speakers in Installing your speaker system on page 18. Make sure to review Placing the speakers on page 19 when placing the speakers in another room.

2Select ‘Speaker B’ from the ‘Surr Back System’ menu.

See Surround back speaker setting on page 35 to do this.

Switching the speaker system

If you selected Speaker B in Surround back speaker setting on page 35, three speaker system settings are possible using the SPEAKERS button. If you selected Normal (SB) or Front Bi-Amp, the button will simply switch your main speaker system on or off. The options

below are for the Speaker B setting only.3

•Use the SPEAKERS button on the front panel to select a speaker system setting.

As mentioned above, if you have selected Normal (SB), the button will simply switch your main speaker system

(A) on or off.

Press repeatedly to choose a speaker system option:

• SP A – Sound is output from speaker system A and the same signal is output from the pre-out terminals.

Note

1To listen to multichannel analog audio you’ll need to select MULTI CH IN (see Selecting the multichannel analog inputs above for more on this).

2• When playback from the multichannel inputs is selected, you can’t use the sound processing features, SIGNAL SELECT, or any of the listening modes (including STEREO and the surround back channel processing).

•When playback from the multichannel inputs is selected, only the volume and channel levels can be set.

•You can’t listen to your speaker B system during playback from the multichannel inputs.

3 • The subwoofer output depends on the settings you made in Manual speaker setup on page 40. However, if SP B is selected above, no sound is heard from the subwoofer (the LFE channel is not downmixed).

•Depending on the settings in Surround back speaker setting on page 35 output from the surround back pre-out terminals may change.

•All speaker systems (except Speaker B connections) are switched off when headphones are connected.

48

En

Page 47 Page 49
Image 48
Page 47 Page 49
Contents VSX-1017TXV-K Federal Communications Commission Declaration of Conformity Keep in a Secure AREA. this is for Your SecurityInformation to User Important Safety Instructions Contents Using other functions Other SettingsOther connections Controlling the rest of your systemFeatures Before you startBefore you start Chapter Installing the receiver When installing this unit, make sure to leave spaceBefore you start Checking what’s in the box VentilationAutomatically setting up for surround sound Auto Mcacc Minute guide02 5 minute guide Chapter Introduction to home theaterMinute guide Follow the instructions on-screenBetter sound using Phase Control Problems when using the Auto Mcacc Setup02 5 minute guide Playing a sourceConnecting your equipment Connecting your equipment ChapterRear panel Connecting your equipment When making cable connectionsAbout the video converter Connect using a stereo RCA/phono jack cable Use a coaxial cable designed for digital audio342 DVD playerConnecting a DVD/HDD recorder, VCR and other video sources Using the component video jacksUse an optical cable for the connection If the device can output digital audio, connect anConnecting using Hdmi Use a three-way component video cableOn an HDMI-compatible monitor.1 Connecting digital audio sources About HdmiCD-R, MD, DAT, etc Connecting a component to the front panel inputs Connecting analog audio sourcesAbout the WMA9 Pro decoder Connecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersBanana plug connections 10 mm 3/8Connecting antennas THX speaker system setupConnecting external antennas Plugging in the receiverAC outlet Out before unpluggingControls and displays Controls and displays ChapterFront panel Operating range of remote control unit Controls and displaysRtrv SoundOver / ATT Dialog EControls and displays Remote control ReceiverInput Select 6TUNE/ST /ENTERMulti OPE ShiftSource MuteListening to your system Listening to your system ChapterListening in surround sound Auto playbackUsing the Home THX modes Using the Advanced surround effectsTHX Games Mode Listening to your systemUsing Front Stage Surround Advance Setting the effect optionsPress EFFECT/CH SEL again to adjust other settings Setting What it does OptionsListening to your system Using Stream Direct Choosing the input signalUsing surround back channel processing Listening with Acoustic Calibration EQUsing the Virtual Surround Back mode Listening to your system Using Midnight and Loudness Using the Sound RetrieverUsing the tone controls Press Tone to select the frequency you want to adjustUsing the tuner Using the tuner ChapterSaving station presets Listening to the radioUsing the tuner Naming station presetsListening to station presets AbcdefghijklmnopqrstuvwxyzSystem Setup menu System Setup menu ChapterMaking receiver settings from the System Setup menu Surround back speaker settingSystem Setup menu Manual Mcacc setup Select ‘Manual MCACC’ from the System Setup menuSelect ‘Fine Ch Level’ from the Manual Mcacc setup menu Fine Channel LevelSystem Setup menu Select ‘Fine SP Distance’ from the Manual Mcacc setup menuFine Speaker Distance Professional Acoustic Calibration EQSetting the Acoustic Calibration EQ automatically Copying your Acoustic Calibration EQ settingsSetting the Acoustic Calibration EQ manually Checking your Acoustic Calibration EQ settingsFront Align System Setup menu Manual speaker setup Speaker SettingSelect ‘Manual SP Setup’ then press Enter Crossover Network Channel LevelTHX Audio Setting THX Speaker SetupSpeaker Distance Connecting an iPod Connecting your iPod to the receiverOther connections Other connections ChapterUsing XM Radio Connecting your XM Radio receiverWatching photos and video content Other connectionsUsing XM HD Surround Saving channel presetsListening to XM Radio Selecting channels and browsing by genreUsing Sirius Radio Connecting your Sirius Connect TunerUsing the XM Menu Listening to channel presetsUsing the Sirius Menu Press Sirius SHIFT+TV to switch to the Sirius inputListening to Sirius Radio Press Class to select one of the three classes thenConnecting the multichannel analog inputs Speaker B setupSwitching the speaker system Selecting the multichannel analog inputsBi-wiring your speakers Bi-amping your front speakersConnect your speakers as shown below Other connections Connecting additional amplifiers Using this receiver with a Pioneer plasma displayPioneer plasma DisplayUsing the SR+ mode with a Pioneer plasma display DVD playerSatellite receiver, etc DVD/LDOther Settings Other Settings ChapterInput Assign menu Assigning the digital inputsOther Settings Other Setup menuDynamic Range Control Setup Dual Mono SetupLFE Attenuator Setup SR+ Setup for Pioneer plasma displaysVideo Converter Setup Using other functions Using other functions ChapterReducing the level of an analog signal Using the sleep timerUsing other functions Dimming the display Switching the speaker impedanceResetting the system Display shows RESET?Controlling the rest of your system LCD shows OK to confirm the setting Select the button for the command you want to inputControlling the rest of your system Multi Operation and System OffUsing multi operations Using System offControls for TVs Buttons Function ComponentsFunction Components CH ++ CH + CH+Decide which component you want to use the remote sensor OUTTroubleshooting PowerAdditional information Additional information ChapterOther audio problems SymptomRemedyAdditional information Settings Phase Control featureVideo Display 96 kHzRemote control Symptom Cause ActionError IPod messagesXM radio messages Sirius radio messagesAdditional information Surround sound formats DolbyAbout THX Windows MediaTM Audio 9 ProfessionalListening modes with different input signal formats Stereo 2 channel signal formatsInput signal format Standard Auto SurroundMultichannel signal formats Additional information Specifications Cleaning the unitTo establish a safe level Once you have established a comfortable sound levelDecibel Level Example Pioneer Corporation

VSX1017TXV specifications

The Pioneer VSX-1017TXV is a versatile and powerful home theater receiver that caters to audiophiles and casual listeners alike. This 7.1-channel receiver is known for its ability to deliver immersive audio experiences, making it an excellent choice for anyone looking to enhance their home entertainment setup.

One of the main features of the VSX-1017TXV is its robust power output. With 100 watts per channel, it is equipped to drive a wide range of speakers while providing clear and dynamic sound. The receiver supports various surround sound formats, including Dolby Digital EX, DTS-ES, and Dolby Pro Logic IIx, allowing users to fully immerse themselves in the action of their favorite movies and games.

Another key characteristic of the Pioneer VSX-1017TXV is its advanced HDMI connectivity. With multiple HDMI inputs, the receiver can easily integrate with modern devices such as Blu-ray players, gaming consoles, and streaming devices. The unit supports high-definition audio formats like Dolby TrueHD and DTS-HD Master Audio, ensuring that users experience their media in the best possible quality.

The receiver also features Pioneer's MCACC (Multi-Channel Acoustic Calibration System) technology. This innovative system automatically analyzes the acoustics of the room and calibrates the audio output accordingly. As a result, users can enjoy optimal sound quality tailored to their specific listening environment without the need for extensive manual adjustments.

In addition to its audio capabilities, the VSX-1017TXV includes a variety of practical features for everyday use. The on-screen display simplifies navigation through menus and settings, while its remote control allows for easy operation from across the room. The receiver supports multi-zone functionality, enabling users to send audio to different areas of the house simultaneously.

With a sleek design that fits seamlessly into any home entertainment setup, the Pioneer VSX-1017TXV combines style with performance. Its solid build quality and user-friendly interface make it an ideal choice for those looking to elevate their home theater experience. Overall, the VSX-1017TXV stands out as a strong contender in the home audio market, delivering impressive sound and advanced features.
Top Page Image Contents