Pioneer VSX1017TXV manual Additional information Specifications, Cleaning the unit

Page 72

12Additional information

Specifications

Amplifier section

Continuous average power output of 120 watts* per channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no more than 0.2 %** total harmonic distortion (front).

Continuous Power Output (20 Hz to 20 kHz, 8 Ω, 0.09 %)

Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 W + 110 W Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 W Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 W + 110 W Surround back . . . . . . . . . . . . . . . . . . . . . . . . 110 W + 110 W

Continuous Power Output (1 kHz, 6 Ω, 1.0 %)

Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W + 150 W Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W + 150 W Surround back . . . . . . . . . . . . . . . . . . . . . . . . 150 W + 150 W

Total harmonic distortion . . . . . . . . . . . . . . . . . . . . . . . 0.05 % (20 Hz to 20 kHz, 100 W, 8 Ω)

*Measured pursuant to the Federal Trade Commission’s Trade Regulation rule on Power Output Claims for Amplifiers

**Measured by Audio Spectrum Analyzer

Audio Section

Input (Sensitivity/Impedance)

LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 mV/47 kΩ Frequency Response (LINE) . . . . . . 5 Hz to 100 000 Hz dB Output (Level/Impedance)

REC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 mV/2.2 kΩ Tone Control

BASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 6 dB (100 Hz) TREBLE . . . . . . . . . . . . . . . . . . . . . . . . . . ± 6 dB (10 kHz) LOUDNESS . . . . . . . . . . +4 dB / +2 dB (100 Hz/10 kHz)

(at volume position –40 dB)

Signal-to-Noise Ratio (IHF, short circuited, A network)

LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 dB Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]

LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 dB

FM Tuner Section

Frequency Range . . . . . . . . . . . . . . . . . 87.5 MHz to 108 MHz Usable Sensitivity . . . . . . . Mono: 13.2 dBf, IHF (1.3 µV/75 Ω) 50 dB Quieting Sensitivity . . . . . . . . . . . . . . . Mono: 20.2 dBf Stereo: 38.6 dBf Signal-to-Noise Ratio . . . . . . . . . . . . Mono: 73 dB (at 85 dBf) Stereo: 70 dB (at 85 dBf)

Distortion . . . . . . . . . . . . . . . . . . . . . . . .Stereo: 0.5 % (1 kHz) Alternate Channel Selectivity . . . . . . . . . . . . 60 dB (400 kHz) Stereo Separation . . . . . . . . . . . . . . . . . . . . . . . . 40 dB (1 kHz) Frequency Response . . . . . . . . . . . . 30 Hz to 15 kHz ± 1 dB Antenna Input . . . . . . . . . . . . . . . . . . . . . . . .75 Ω unbalanced

AM Tuner Section

Frequency Range . . . . . . . . . . . . . . . . . . 530 kHz to 1700 kHz Sensitivity (IHF, Loop antenna) . . . . . . . . . . . . . . . . 350 µV/m Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 dB Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 dB Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loop antenna

Miscellaneous

Power Requirements . . . . . . . . . . . . . . . . . . . AC 120 V, 60 Hz Power Consumption . . . . . . . . . . . . . . . . . . . . . 490 W, 650 VA In standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 W AC Outlet . . . . . . . . . . . . . . . . . . . . . . (switched) 100 W MAX. Dimensions . . . . . . 420 (W) mm x 173 (H) mm x 465 (D) mm

(16 9/16 (W) in. x 6 13/16 (H) in. x 18 5/16 (D) in.) Weight (without package) . . . . . . . . . . . .15.0 kg (33 lbs 1 oz)

Furnished Parts

Setup microphone (for Auto MCACC setup) . . . . . . . . . . . . 1 AA/IEC R6P dry cell batteries . . . . . . . . . . . . . . . . . . . . . . . 2 Remote control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AM loop antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 These operating instructions

Note

•Specifications and the design are subject to possible modifications without notice, due to improvements.

Composite Video / S-Video Section

Input (Sensitivity/Impedance) . . . . . . . . . . . . . . . .1 Vp-p/75 Ω Output (Level/Impedance) . . . . . . . . . . . . . . . . . . .1 Vp-p/75 Ω Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 dB Frequency Response . . . . . . . . . . . . . . . . . . . . 5 Hz to 10 MHz

Component Video Section

Input (Sensitivity/Impedance) . . . . . . . . . . . . . . . .1 Vp-p/75 Ω Output (Level/Impedance) . . . . . . . . . . . . . . . . . . .1 Vp-p/75 Ω Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 dB Frequency Response . . . . . . . . . . . . . . . . . . . 5 Hz to 100 MHz

Cleaning the unit

•Use a polishing cloth or dry cloth to wipe off dust and dirt.

•When the surface is dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water, and wrung out well, and then wipe again with a dry cloth. Do not use furniture wax or cleansers.

•Never use thinners, benzine, insecticide sprays or other chemicals on or near this unit, since these will corrode the surface.

72

En

Page 71 Page 73
Image 72
Page 71 Page 73
Contents VSX-1017TXV-K Federal Communications Commission Declaration of Conformity Keep in a Secure AREA. this is for Your SecurityInformation to User Important Safety Instructions Contents Using other functions Other SettingsOther connections Controlling the rest of your systemFeatures Before you startBefore you start Chapter Installing the receiver When installing this unit, make sure to leave spaceBefore you start Checking what’s in the box VentilationAutomatically setting up for surround sound Auto Mcacc Minute guide02 5 minute guide Chapter Introduction to home theaterMinute guide Follow the instructions on-screenBetter sound using Phase Control Problems when using the Auto Mcacc Setup02 5 minute guide Playing a sourceConnecting your equipment Connecting your equipment ChapterRear panel Connecting your equipment When making cable connectionsAbout the video converter Connect using a stereo RCA/phono jack cable Use a coaxial cable designed for digital audio342 DVD playerConnecting a DVD/HDD recorder, VCR and other video sources Using the component video jacksUse an optical cable for the connection If the device can output digital audio, connect anConnecting using Hdmi Use a three-way component video cableOn an HDMI-compatible monitor.1 Connecting digital audio sources About HdmiCD-R, MD, DAT, etc Connecting a component to the front panel inputs Connecting analog audio sourcesAbout the WMA9 Pro decoder Connecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersBanana plug connections 10 mm 3/8Connecting antennas THX speaker system setupConnecting external antennas Plugging in the receiverAC outlet Out before unpluggingControls and displays Controls and displays ChapterFront panel Operating range of remote control unit Controls and displaysRtrv SoundOver / ATT Dialog EControls and displays Remote control ReceiverInput Select 6TUNE/ST /ENTERMulti OPE ShiftSource MuteListening to your system Listening to your system ChapterListening in surround sound Auto playbackUsing the Home THX modes Using the Advanced surround effectsTHX Games Mode Listening to your systemUsing Front Stage Surround Advance Setting the effect optionsPress EFFECT/CH SEL again to adjust other settings Setting What it does OptionsListening to your system Using Stream Direct Choosing the input signalUsing surround back channel processing Listening with Acoustic Calibration EQUsing the Virtual Surround Back mode Listening to your system Using Midnight and Loudness Using the Sound RetrieverUsing the tone controls Press Tone to select the frequency you want to adjustUsing the tuner Using the tuner ChapterSaving station presets Listening to the radioUsing the tuner Naming station presetsListening to station presets AbcdefghijklmnopqrstuvwxyzSystem Setup menu System Setup menu ChapterMaking receiver settings from the System Setup menu Surround back speaker settingSystem Setup menu Manual Mcacc setup Select ‘Manual MCACC’ from the System Setup menuSelect ‘Fine Ch Level’ from the Manual Mcacc setup menu Fine Channel LevelSystem Setup menu Select ‘Fine SP Distance’ from the Manual Mcacc setup menuFine Speaker Distance Professional Acoustic Calibration EQSetting the Acoustic Calibration EQ automatically Copying your Acoustic Calibration EQ settingsSetting the Acoustic Calibration EQ manually Checking your Acoustic Calibration EQ settingsFront Align System Setup menu Manual speaker setup Speaker SettingSelect ‘Manual SP Setup’ then press Enter Crossover Network Channel LevelTHX Audio Setting THX Speaker SetupSpeaker Distance Connecting an iPod Connecting your iPod to the receiverOther connections Other connections ChapterUsing XM Radio Connecting your XM Radio receiverWatching photos and video content Other connectionsUsing XM HD Surround Saving channel presetsListening to XM Radio Selecting channels and browsing by genreUsing Sirius Radio Connecting your Sirius Connect TunerUsing the XM Menu Listening to channel presetsUsing the Sirius Menu Press Sirius SHIFT+TV to switch to the Sirius inputListening to Sirius Radio Press Class to select one of the three classes thenConnecting the multichannel analog inputs Speaker B setupSwitching the speaker system Selecting the multichannel analog inputsBi-wiring your speakers Bi-amping your front speakersConnect your speakers as shown below Other connections Connecting additional amplifiers Using this receiver with a Pioneer plasma displayPioneer plasma DisplayUsing the SR+ mode with a Pioneer plasma display DVD playerSatellite receiver, etc DVD/LDOther Settings Other Settings ChapterInput Assign menu Assigning the digital inputsOther Settings Other Setup menuDynamic Range Control Setup Dual Mono SetupLFE Attenuator Setup SR+ Setup for Pioneer plasma displaysVideo Converter Setup Using other functions Using other functions ChapterReducing the level of an analog signal Using the sleep timerUsing other functions Dimming the display Switching the speaker impedanceResetting the system Display shows RESET?Controlling the rest of your system LCD shows OK to confirm the setting Select the button for the command you want to inputControlling the rest of your system Multi Operation and System OffUsing multi operations Using System offControls for TVs Buttons Function ComponentsFunction Components CH ++ CH + CH+Decide which component you want to use the remote sensor OUTTroubleshooting PowerAdditional information Additional information ChapterOther audio problems SymptomRemedyAdditional information Settings Phase Control featureVideo Display 96 kHzRemote control Symptom Cause ActionError IPod messagesXM radio messages Sirius radio messagesAdditional information Surround sound formats DolbyAbout THX Windows MediaTM Audio 9 ProfessionalListening modes with different input signal formats Stereo 2 channel signal formatsInput signal format Standard Auto SurroundMultichannel signal formats Additional information Specifications Cleaning the unitTo establish a safe level Once you have established a comfortable sound levelDecibel Level Example Pioneer Corporation

VSX1017TXV specifications

The Pioneer VSX-1017TXV is a versatile and powerful home theater receiver that caters to audiophiles and casual listeners alike. This 7.1-channel receiver is known for its ability to deliver immersive audio experiences, making it an excellent choice for anyone looking to enhance their home entertainment setup.

One of the main features of the VSX-1017TXV is its robust power output. With 100 watts per channel, it is equipped to drive a wide range of speakers while providing clear and dynamic sound. The receiver supports various surround sound formats, including Dolby Digital EX, DTS-ES, and Dolby Pro Logic IIx, allowing users to fully immerse themselves in the action of their favorite movies and games.

Another key characteristic of the Pioneer VSX-1017TXV is its advanced HDMI connectivity. With multiple HDMI inputs, the receiver can easily integrate with modern devices such as Blu-ray players, gaming consoles, and streaming devices. The unit supports high-definition audio formats like Dolby TrueHD and DTS-HD Master Audio, ensuring that users experience their media in the best possible quality.

The receiver also features Pioneer's MCACC (Multi-Channel Acoustic Calibration System) technology. This innovative system automatically analyzes the acoustics of the room and calibrates the audio output accordingly. As a result, users can enjoy optimal sound quality tailored to their specific listening environment without the need for extensive manual adjustments.

In addition to its audio capabilities, the VSX-1017TXV includes a variety of practical features for everyday use. The on-screen display simplifies navigation through menus and settings, while its remote control allows for easy operation from across the room. The receiver supports multi-zone functionality, enabling users to send audio to different areas of the house simultaneously.

With a sleek design that fits seamlessly into any home entertainment setup, the Pioneer VSX-1017TXV combines style with performance. Its solid build quality and user-friendly interface make it an ideal choice for those looking to elevate their home theater experience. Overall, the VSX-1017TXV stands out as a strong contender in the home audio market, delivering impressive sound and advanced features.
Top Page Image Contents