Pioneer VSX1017TXV manual LFE Attenuator Setup, SR+ Setup for Pioneer plasma displays

09Other Settings

1Select ‘Dual Mono Setup’ from the Other Setup menu.

6.Other Setup			6b.Dual Mono	Setup
	a.DRC	Setup
	b.Dual	Mono Setup	Dual Mono
	c.LFE	ATT Setup			[ CH1
	d.SR+	Setup
	e.Video Conv. Setup
		:Return			:Finish

2Choose the setting that you want.

•CH1 – Only channel 1 is played

•CH2 – Only channel 2 is played

•CH1 CH2 – Both channels are played through the front speakers

3When you're finished, press RETURN.

You return to the Other Setup menu.

LFE Attenuator Setup

• Default setting: ATT 0dB

Some Dolby Digital and DTS audio sources include ultra- low bass tones. Set the LFE attenuator as necessary to prevent the ultra-low bass tones from distorting the sound from the speakers.

1 Select ‘LFE ATT Setup’ from the Other Setup menu.

6.Other Setup			6c. LFE ATT	Setup
	a.DRC	Setup
	b.Dual	Mono Setup	LFE ATT
	c.LFE	ATT Setup			ATT 0dB
	d.SR+	Setup
	e.Video Conv. Setup
		:Return			:Finish

2Choose the setting that you want.

•ATT 0dB – No limiting (recommended)

•ATT 10dB – 10 dB of limiting

•LFE OFF – No sound from LFE channel

3When you're finished, press RETURN. You return to the Other Setup menu.

SR+ Setup for Pioneer plasma displays

• Default setting: OFF (all settings)

Make the following settings if you have connected a Pioneer plasma display to this receiver using an SR+ cable. Note that the number of settings available will depend on the plasma display you’ve connected.

See also Using this receiver with a Pioneer plasma display on page 50.

1 Select ‘SR+ Setup’ from the Other Setup menu.

6.Other Setup				6d.SR+ Setup
				PDP Volume	Control
	a.DRC	Setup
						OFF
	b.Dual	Mono	Setup
				PDP Input Select
	c.LFE	ATT Setup
				DVD/LD	[		OFF	]
	d.SR+	Setup
	e.Video Conv. Setup			TV/SAT	[		OFF	]
				DVR 1	[		OFF	]
				DVR 2	[		OFF	]
				VIDEO	[		OFF	]
				Monitor Out	[		OFF	]
			:Return				:Finish

54

2Select the ‘PDP Volume Control’ setting you want.

•OFF – The receiver does not control the volume of the plasma display

•ON – When the receiver is switched to one of the inputs that use the plasma display (DVD/LD, or another function below), the volume on the plasma display is muted so only sound from the receiver is heard.

3Assign any input source connected to the plasma display to the corresponding input number.

This matches the receiver’s input source with a numbered video input on the plasma display. For example, assign DVD/LD to input-2if you have connected your DVD video output to video input 2 on the plasma display.

•The Monitor Out should be set to the input that you’ve used to connect this receiver to your plasma display.

6d.SR+ Setup				6d.SR+ Setup
PDP Volume	Control			PDP Volume	Control
	[ ON ]				[ ON ]
PDP Input Select				PDP Input Select
DVD/LD		OFF		DVD/LD		input-2
TV/SAT	[	OFF	]	TV/SAT	[	OFF	]
DVR 1	[	OFF	]	DVR 1	[	OFF	]
DVR 2	[	OFF	]	DVR 2	[	OFF	]
VIDEO	[	OFF	]	VIDEO	[	OFF	]
Monitor Out	[	OFF	]	Monitor Out	[	OFF	]
		:Finish				:Finish

4When you're finished, press RETURN. You return to the Other Setup menu.

Video Converter Setup

• Default setting: ON

The video converter allows you to see analog video sources through all of this receiver’s MONITOR VIDEO OUT jacks. Note that the converter gives priority to component, S-video, then composite (in that order). See About the video converter on page 12 for more on this.

1Select ‘Video Conv. Setup’ from the Other Setup menu.

6.Other Setup			6e. Video Converter Setup
	a.DRC	Setup
	b.Dual	Mono Setup	Video Conv.
	c.LFE	ATT Setup		ON
	d.SR+	Setup
	e.Video Conv. Setup
		:Return		:Finish

2Choose the setting that you want.

•ON – All analog video signals are output from the MONITOR VIDEO OUT jacks.

•OFF – No conversion between video formats.

3When you're finished, press RETURN.

You return to the Other Setup menu.

En