Pioneer VSX1017TXV manual Video, Settings, Phase Control feature

Page 64

12Additional information

Symptom

Remedy

Subwoofer output is very low.

• To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL (see Speaker

 

Setting on page 40).

 

 

Everything seems to be set up

• The speakers may be out of phase. Check that the positive/negative speaker terminals on the receiver are

correctly, but the playback sound

matched with the corresponding terminals on the speakers (see Connecting the speakers on page 18).

is odd.

 

 

 

The PHASE CONTROL feature

• If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is set to

doesn’t seem to have an audible

the highest frequency setting. If there is a PHASE setting on your subwoofer, set it to 0º (or depending on

effect.

the subwoofer, the setting where you think it has the best overall effect on the sound).

 

• Make sure the speaker distance setting is correct for all speakers (see Speaker Distance on page 42).

 

 

Noise or hum can be heard even

• Check that personal computers or other digital components connected to the same power source are not

when there is no sound being

causing interference.

input.

 

 

 

There seems to be a time lag

• See Automatically setting up for surround sound (Auto MCACC) on page 8 to set up your system again

between the speakers and the

using MCACC (this will automatically compensate for a delay in the subwoofer output).

output of the subwoofer.

 

 

 

The maximum volume available

• This is not a malfunction. If the levels in Channel Level on page 41 have been adjusted, the maximum

(shown in the front panel display)

volume will change accordingly.

is lower than the +12dB

 

maximum.

 

 

 

Video

Symptom

Remedy

No image is output when an input

• Check the video connections of the source component (see page 14).

is selected.

• Make sure the input assignment is correct for components connected using component cables (see The

 

Input Assign menu on page 52).

 

• Check the video output settings of the source component.

 

• Check that the video input you selected on your TV is correct.

 

• When the source component is connected to this receiver with a component video cable, you must also

 

connect your TV to this receiver with a component video cable.

 

 

Can’t record video.

• Check that the source is not copy-protected.

 

• The video converter is not available when making recordings. Check that the same type of video cable is

 

used for connecting both the recorder and the video source (the one you want to record) to this receiver.

 

 

Noisy, intermittent, or distorted

• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the video

picture.

quality may just be poor (with some video game units, for example). The picture quality may also depend on

 

the settings, etc. of your display device. Switch off the video converter and reconnect the source and display

 

device using the same type of connection (component, S-video or composite), then start playback again.

 

 

Settings

Symptom

Remedy

The Auto MCACC Setup

• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see also

continually shows an error.

Problems when using the Auto MCACC Setup on page 10). If the noise level cannot be kept low enough, you

 

will have to set up the surround sound manually (page 36).

 

 

After using the Auto MCACC

• There may have been some low frequency noise in the room from an air-conditioner, motor, etc. Switch

Setup, the speaker size setting is

off all other appliances in the room and use Auto MCACC Setup again.

incorrect.

• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some cases.

 

You can change the speaker setting manually in Speaker Setting on page 40 if this is a recurring problem.

 

 

Can’t adjust the Fine Speaker

• Check that the speakers are all in phase (make sure the positive (+) and negative (–) terminals are

Distance setting (page 37)

matched up properly).

properly.

 

 

 

Most recent settings have been

• The power cord was disconnected from the wall while adjusting this setting.

erased.

 

 

 

64

En

Page 63 Page 65
Image 64
Page 63 Page 65
Contents VSX-1017TXV-K Keep in a Secure AREA. this is for Your Security Federal Communications Commission Declaration of ConformityInformation to User Important Safety Instructions Contents Using other functions Other SettingsOther connections Controlling the rest of your systemBefore you start FeaturesBefore you start Chapter Installing the receiver When installing this unit, make sure to leave spaceBefore you start Checking what’s in the box VentilationAutomatically setting up for surround sound Auto Mcacc Minute guide02 5 minute guide Chapter Introduction to home theaterMinute guide Follow the instructions on-screenBetter sound using Phase Control Problems when using the Auto Mcacc Setup02 5 minute guide Playing a sourceConnecting your equipment Chapter Connecting your equipmentRear panel When making cable connections Connecting your equipmentAbout the video converter Connect using a stereo RCA/phono jack cable Use a coaxial cable designed for digital audio342 DVD playerConnecting a DVD/HDD recorder, VCR and other video sources Using the component video jacksUse an optical cable for the connection If the device can output digital audio, connect anUse a three-way component video cable Connecting using HdmiOn an HDMI-compatible monitor.1 About Hdmi Connecting digital audio sourcesCD-R, MD, DAT, etc Connecting analog audio sources Connecting a component to the front panel inputsAbout the WMA9 Pro decoder Connecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersBanana plug connections 10 mm 3/8Connecting antennas THX speaker system setupConnecting external antennas Plugging in the receiverAC outlet Out before unpluggingControls and displays Chapter Controls and displaysFront panel Operating range of remote control unit Controls and displaysRtrv SoundOver / ATT Dialog EControls and displays Remote control ReceiverInput Select 6TUNE/ST /ENTERMulti OPE ShiftSource MuteListening to your system Listening to your system ChapterListening in surround sound Auto playbackUsing the Home THX modes Using the Advanced surround effectsTHX Games Mode Listening to your systemUsing Front Stage Surround Advance Setting the effect optionsPress EFFECT/CH SEL again to adjust other settings Setting What it does OptionsListening to your system Using Stream Direct Choosing the input signalUsing surround back channel processing Listening with Acoustic Calibration EQUsing the Virtual Surround Back mode Listening to your system Using Midnight and Loudness Using the Sound RetrieverUsing the tone controls Press Tone to select the frequency you want to adjustUsing the tuner Using the tuner ChapterSaving station presets Listening to the radioUsing the tuner Naming station presetsListening to station presets AbcdefghijklmnopqrstuvwxyzSystem Setup menu System Setup menu ChapterMaking receiver settings from the System Setup menu Surround back speaker settingSystem Setup menu Manual Mcacc setup Select ‘Manual MCACC’ from the System Setup menuSelect ‘Fine Ch Level’ from the Manual Mcacc setup menu Fine Channel LevelSystem Setup menu Select ‘Fine SP Distance’ from the Manual Mcacc setup menuFine Speaker Distance Professional Acoustic Calibration EQSetting the Acoustic Calibration EQ automatically Copying your Acoustic Calibration EQ settingsChecking your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ manuallyFront Align Speaker Setting System Setup menu Manual speaker setupSelect ‘Manual SP Setup’ then press Enter Crossover Network Channel LevelTHX Speaker Setup THX Audio SettingSpeaker Distance Connecting an iPod Connecting your iPod to the receiverOther connections Other connections ChapterUsing XM Radio Connecting your XM Radio receiverWatching photos and video content Other connectionsUsing XM HD Surround Saving channel presetsListening to XM Radio Selecting channels and browsing by genreUsing Sirius Radio Connecting your Sirius Connect TunerUsing the XM Menu Listening to channel presetsUsing the Sirius Menu Press Sirius SHIFT+TV to switch to the Sirius inputListening to Sirius Radio Press Class to select one of the three classes thenConnecting the multichannel analog inputs Speaker B setupSwitching the speaker system Selecting the multichannel analog inputsBi-amping your front speakers Bi-wiring your speakersConnect your speakers as shown below Other connections Connecting additional amplifiers Using this receiver with a Pioneer plasma displayPioneer plasma DisplayUsing the SR+ mode with a Pioneer plasma display DVD playerSatellite receiver, etc DVD/LDOther Settings Other Settings ChapterInput Assign menu Assigning the digital inputsOther Settings Other Setup menuDynamic Range Control Setup Dual Mono SetupSR+ Setup for Pioneer plasma displays LFE Attenuator SetupVideo Converter Setup Using other functions Using other functions ChapterReducing the level of an analog signal Using the sleep timerUsing other functions Dimming the display Switching the speaker impedanceResetting the system Display shows RESET?Controlling the rest of your system LCD shows OK to confirm the setting Select the button for the command you want to inputControlling the rest of your system Multi Operation and System OffUsing multi operations Using System offControls for TVs Buttons Function ComponentsFunction Components CH ++ CH + CH+Decide which component you want to use the remote sensor OUTTroubleshooting PowerAdditional information Additional information ChapterSymptomRemedy Other audio problemsAdditional information Phase Control feature SettingsVideo Display 96 kHzRemote control Symptom Cause ActionError IPod messagesXM radio messages Sirius radio messagesAdditional information Surround sound formats DolbyAbout THX Windows MediaTM Audio 9 ProfessionalListening modes with different input signal formats Stereo 2 channel signal formatsInput signal format Standard Auto SurroundMultichannel signal formats Additional information Specifications Cleaning the unitOnce you have established a comfortable sound level To establish a safe levelDecibel Level Example Pioneer Corporation

VSX1017TXV specifications

The Pioneer VSX-1017TXV is a versatile and powerful home theater receiver that caters to audiophiles and casual listeners alike. This 7.1-channel receiver is known for its ability to deliver immersive audio experiences, making it an excellent choice for anyone looking to enhance their home entertainment setup.

One of the main features of the VSX-1017TXV is its robust power output. With 100 watts per channel, it is equipped to drive a wide range of speakers while providing clear and dynamic sound. The receiver supports various surround sound formats, including Dolby Digital EX, DTS-ES, and Dolby Pro Logic IIx, allowing users to fully immerse themselves in the action of their favorite movies and games.

Another key characteristic of the Pioneer VSX-1017TXV is its advanced HDMI connectivity. With multiple HDMI inputs, the receiver can easily integrate with modern devices such as Blu-ray players, gaming consoles, and streaming devices. The unit supports high-definition audio formats like Dolby TrueHD and DTS-HD Master Audio, ensuring that users experience their media in the best possible quality.

The receiver also features Pioneer's MCACC (Multi-Channel Acoustic Calibration System) technology. This innovative system automatically analyzes the acoustics of the room and calibrates the audio output accordingly. As a result, users can enjoy optimal sound quality tailored to their specific listening environment without the need for extensive manual adjustments.

In addition to its audio capabilities, the VSX-1017TXV includes a variety of practical features for everyday use. The on-screen display simplifies navigation through menus and settings, while its remote control allows for easy operation from across the room. The receiver supports multi-zone functionality, enabling users to send audio to different areas of the house simultaneously.

With a sleek design that fits seamlessly into any home entertainment setup, the Pioneer VSX-1017TXV combines style with performance. Its solid build quality and user-friendly interface make it an ideal choice for those looking to elevate their home theater experience. Overall, the VSX-1017TXV stands out as a strong contender in the home audio market, delivering impressive sound and advanced features.
Top Page Image Contents