Pioneer VSX-1016TXV-K operating instructions Video, Settings

Page 59

Additional information

12

Symptom

Remedy

Subwoofer output is very low.

• To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL (see Speaker

 

Setting on page 37).

 

 

Everything seems to be set up

• The speakers may be out of phase. Check that the positive/negative speaker terminals on the receiver are

correctly, but the playback sound

matched with the corresponding terminals on the speakers (see Connecting the speakers on page 17).

is odd.

 

 

 

The PHASE CONTROL feature

• If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is set to

doesn’t seem to have an audible

the highest frequency setting. If there is a PHASE setting on your subwoofer, set it to 0º (or depending on

effect.

the subwoofer, the setting where you think it has the best overall effect on the sound).

 

• Make sure the speaker distance setting is correct for all speakers (see Speaker Distance on page 39).

 

 

Noise or hum can be heard even

• Check that personal computers or other digital components connected to the same power source are not

when there is no sound being

causing interference.

input.

 

 

 

There seems to be a time lag

• See Automatically setting up for surround sound (MCACC) on page 8 to set up your system again using

between the speakers and the

MCACC (this will automatically compensate for a delay in the subwoofer output).

output of the subwoofer.

 

 

 

The maximum volume available

• This is not a malfunction. If the levels in Channel Level on page 38 have been adjusted, the maximum

(shown in the front panel display)

volume will change accordingly.

is lower than the +12 dB

 

maximum.

 

 

 

Video

Symptom

No image is output when an input is selected.

Remedy

•Check the video connections of the source component (see page 14).

•Make sure the input assignment is correct for components connected using component cables (see The Input Assign menu on page 46).

•A separate video source has been selected using VIDEO SELECT (see Watching video and audio sources independently on page 49).

•Check the video output settings of the source component.

•Check that the video input you selected on your TV is correct.

Can’t record video.

• Check that the source is not copy-protected.

 

• The video converter is not available when making recordings. Check that the same type of video cable is

 

used for connecting both the recorder and the video source (the one you want to record) to this receiver.

 

 

Noisy, intermittant, or distorted

• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the video

picture.

quality may just be poor (with some video game units, for example). The picture quality may also depend on

 

the settings, etc. of your display device. Switch off the video converter and reconnect the source and display

 

device using the same type of connection (component, S-video or composite), then start playback again.

 

 

Settings

Symptom

Remedy

The Auto MCACC Setup

• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see also

continually shows an error.

Problems when using the Auto MCACC Setup on page 10). If the noise level cannot be kept low enough, you

 

will have to set up the surround sound manually (page 34).

 

 

After using the Auto MCACC

• There may have been some low frequency noise in the room from an air-conditioner, motor, etc. Switch

Setup, the speaker size setting is

off all other appliances in the room and use Auto MCACC Setup again.

incorrect.

• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some cases.

 

You can change the speaker setting manually in Speaker Setting on page 37 if this is a recurring problem.

 

 

Can’t adjust the Fine Speaker

• Check that the speakers are all in phase (make sure the positive (+) and negative (–) terminals are

Distance setting (page 35)

matched up properly).

properly.

 

 

 

Most recent settings have been

• The power cord was disconnected from the wall while adjusting this setting.

erased.

 

 

 

59

En

Page 58 Page 60
Image 59
Page 58 Page 60
Contents VSX-1016TXV-K Information to User Federal Communications Declaration of ConformityModel Number VSX-1016TXV-K Responsible Party Name Keep in a Secure AREA. this is for Your SecurityImportant Safety Instructions Contents Additional information Other SettingsUsing other functions Other connectionsChecking what’s in the box FeaturesBefore you start Before you start ChapterLoading the batteries Installing the receiverBefore you start Ventilation Introduction to home theater Automatically setting up for surround sound McaccMinute guide 02 5 minute guide ChapterMake sure ‘OK’ is selected, then press Enter Minute guidePlaying a source Better sound using Basic Phase ControlProblems when using the Auto Mcacc Setup 02 5 minute guideRear panel Connecting your equipmentConnecting your equipment Chapter About the video converter Connecting your equipmentWhen making cable connections DVD player Connecting your equipment Connecting your TV and DVD playerConnecting a satellite/cable receiver or other set-top box DVR, VCR, etc Connecting a DVD/HDD recorder, VCR and other video sourcesUsing the component video jacks Use an optical cable for the connectionCD-R, MD, DAT, etc Connecting digital audio sourcesUse a three-way component video cable Tape deck, etc Connecting a component to the front panel inputsConnecting analog audio sources About the WMA9 Pro decoderConnecting the speakers Connecting your equipment Installing your speaker systemBanana plug connections Bare wire connectionsPlacing the speakers THX speaker system setup Connecting antennasAC outlet Connecting external antennasPlug the power cord into a power outlet Plugging in the receiverSTANDBY/ON Controls and displaysControls and displays Chapter Front panelControls and displays Operating range of remote control unitVideo Conv Controls and displays DisplaySleep Over / ATTSelect Controls and displays Remote controlReceiver Input SelectMute Multi OPEShift SourceStandard surround sound Listening to your systemListening to your system Chapter Auto playback Listening in surround soundListening to your system Using the Home THX modesUsing the Advanced surround effects Setting the effect optionsUse the +/- buttons to set it as necessary Press EFFECT/CH SEL again to adjust other settingsListening with Acoustic Calibration EQ Listening in stereoUsing the Virtual Surround Back mode Listening to your system Choosing the input signalPress Tone to select the frequency you want to adjust Using Midnight and LoudnessUsing the Sound Retriever Using the tone controlsListening to the radio Using the tunerUsing the tuner Chapter Saving station presetsAbcdefghijklmnopqrstuvwxyz Using the tunerNaming station presets Listening to station presetsSurround back speaker setting System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuFine Channel Level System Setup menu Manual Mcacc setupSelect ‘Manual MCACC’ from the System Setup menu Select ‘Fine Ch Level’ from the Manual Mcacc setup menuAcoustic Calibration EQ System Setup menuSetting the Acoustic Calibration EQ automatically Fine Speaker DistanceFront Align Copying your Acoustic Calibration EQ settingsSetting the Acoustic Calibration EQ manually Checking your Acoustic Calibration EQ settingsSpeaker Setting Manual speaker setupChannel Level Crossover NetworkSpeaker Distance THX Speaker SetupTHX Audio Setting Other connections Chapter Using XM RadioConnecting your XM Radio receiver Other connectionsOther connections Connecting using HdmiUsing XM HD Surround Saving channel presetsUse standard RCA/phono jack cables for the connections Second Zone speaker B setupAbout Hdmi Selecting the multichannel analog inputsConnect your speakers as shown below Switching the speaker system2nd Zone setting only.1 Bi-amping your front speakersLarge Other connections Bi-wiring your speakersUsing this receiver with a Pioneer plasma display Display Using the SR+ mode with a Pioneer plasma displayDVD player Pioneer plasmaAssigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuAssigning the Hdmi inputs Other SettingsOther Setup menu Dynamic Range Control SetupVideo Converter Setup Dual Mono SetupLFE Attenuator Setup SR+ Setup for Pioneer plasma displaysMaking an audio or a video recording Using other functionsUsing other functions Chapter Reducing the level of an analog signalDisplay shows RESET? Using other functions Using the sleep timerResetting the system Switching the speaker impedanceControlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Programming signals from other remote controlsControlling the rest of your system Erasing one of the remote control button settingsResetting the remote control presets Confirming preset codesProgramming a multi-operation or a shutdown sequence Use to switch direct function on or OFF then press EnterDirect function Multi Operation and System OffUsing System off Using multi operationsControls for other components Controlling the rest of your system Controls for TVsDecide which component you want to use the remote sensor Operating other Pioneer components with this unit’s sensorAdditional information Chapter TroubleshootingPower Additional informationAdditional information Other audio problemsVideo SettingsDisplay Remote controlXM radio messages HdmiWindows Media Audio 9 Professional Additional information Surround sound formatsDolby About THX THX MusicMode Listening modes with different input signal formatsStereo 2 channel signal formats THX Games ModeAuto Multichannel signal formatsCleaning the unit Additional information SpecificationsDecibel Level Example To establish a safe levelOnce you have established a comfortable sound level Pioneer Corporation

VSX-1016TXV-K specifications

The Pioneer VSX-1016TXV-K is a versatile and powerful A/V receiver that brings a wealth of features and technologies to enhance your home entertainment experience. Built with the audiophile in mind, it combines high-performance sound quality with modern connectivity and smart functionality.

One of the main features of the VSX-1016TXV-K is its robust amplification system, which delivers an impressive 7.1-channel surround sound experience. With a total output of 110 watts per channel, this receiver is capable of driving a variety of speakers, ensuring that every audio detail is crisp and immersive. This makes it an ideal choice for both movie watchers and music enthusiasts.

The receiver supports numerous audio formats, including Dolby TrueHD and DTS-HD Master Audio, providing lossless audio quality for high-definition content. This commitment to audio excellence is complemented by its use of advanced technologies such as the Pioneer MCACC (Multi-Channel Acoustic Calibration System), which automatically adjusts the receiver's settings based on the acoustics of your room, ensuring optimal sound performance.

In terms of connectivity, the VSX-1016TXV-K is equipped with multiple HDMI inputs, which support 1080p video pass-through and are compatible with the latest HDMI standards. This makes it easy to connect various devices such as Blu-ray players, gaming consoles, and streaming devices, allowing seamless switching between sources. The unit also includes component and composite video inputs, as well as optical and coaxial digital audio inputs for greater flexibility.

Additionally, the receiver features an integrated AM/FM tuner, allowing listeners to enjoy their favorite radio stations. The user-friendly on-screen display and menu system enable easy navigation through different settings and offers access to a wide range of features, including preset equalizer settings and listening modes.

The VSX-1016TXV-K is designed with aesthetics in mind, featuring a sleek black finish that fits well in any home theater environment. Its robust build quality ensures durability while providing an attractive addition to your audio setup.

In conclusion, the Pioneer VSX-1016TXV-K A/V receiver stands out in the crowded market of home audio equipment with its exceptional sound performance, extensive connectivity options, and thoughtful user features. Whether you're hosting movie nights or enjoying your favorite music, this receiver delivers an impressive and engaging listening experience.
Top Page Image Contents