Pioneer VSX-1014TX manual Follow the instructions on-screen

Page 12

025 minute guide

6Follow the instructions on-screen.

2.AUTO MCACC

•Set microphone

•Turn on Sub Woofer

Return : Cancel

•Make sure the microphone is connected.

•If you’re using a subwoofer, it is automatically detected every time you switch on the system. Make sure it is on and the volume is turned up.

•See below for notes regarding high background noise levels and other possible interference.

7Wait for the Auto MCACC Setup to finish outputting test tones.

A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present in your setup. Try to be as quiet as possible while it’s doing this.

2. AUTO MCACC

 

2. AUTO MCACC

 

 

 

 

Now Analyzing•••

 

 

 

 

 

 

 

 

 

Please wait

 

Environment Check

 

 

 

Ambient Noise

[

]

Caution!!

 

Microphone

[

]

 

Speaker YES/NO

[

]

Test tone is

 

 

 

 

 

 

output loudly.

 

 

 

 

 

 

Return:Cancel

 

 

Return:Cancel

 

 

 

 

 

 

 

•Do not adjust the volume during the test tones. This may result in incorrect speaker settings.

8Confirm the speaker configuration in the OSD. The configuration shown on-screen should reflect the actual speakers you have.

2. AUTO MCACC

 

 

Check!!!

 

 

Front

[ YES ]

Center

[ YES ]

Surround

[ YES ]

Surr Back

[ YES X 2]

Sub Woofer

[ YES ]

[

 

]

OK

 

 

 

If the speaker configuration displayed isn’t correct, use

the

(cursor up/down) buttons to select the speaker

and

(cursor left/right) to change the setting (and

number for surround back). When you’re finished, go to the next step.

If you see an error message (ERR) in the right side column, there may be a problem with the speaker connection. If selecting RETRY doesn’t fix the problem, turn off the power and check the speaker connections.

9Make sure ‘OK’ is selected, then press ENTER. A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum receiver settings for channel level, speaker distance, and Acoustic Calibration EQ.

2.AUTO MCACC Now Analyzing•••

Surround

Analyzing

 

 

Speaker

System

[

]

Speaker

Distance

[

]

Channel

Level

[

]

Acoustic Cal EQ

[

]

Return:Cancel

Again, try to be as quiet as possible while this is happening. It may take 3–8 minutes.

10The Auto MCACC Setup has finished! Select ‘Skip’ to go back to the System Setup menu.

The MCACC indicator on the front panel will light to show the surround settings are complete.

2.AUTO MCACC Analyzed Data Check

[a.Speaker Setting

]

[b.Speaker Distance

]

[c.Channel Level

]

[d.Acoustic Cal EQ

]

 

[

 

]

 

Skip

The settings made in the Auto MCACC Setup should give you excellent surround sound from your system, but it is also possible to adjust these settings manually using the System Setup menu (starting on page 38).

•If you are using THX Certified speakers, confirm that all speakers are set to SMALL in Speaker Setting on page 44, and that the Crossover Network on page 45 is set to 80Hz.

You can also choose to view the settings by selecting individual parameters from the Analyzed Data Check screen:

•Speaker Setting – The size and number of speakers you’ve connected (see page 44 for more on this)

•Speaker Distance – The distance of your speakers from the listening position (see page 46 for more on this)

•Channel Level – The overall balance of your speaker system (see page 45 for more on this)

•Acoustic Cal EQ – Adjustments to the frequency balance of your speaker system based on the acoustic characteristics of your room (see page 41 for more on this)

Press RETURN after you have finished checking each screen. When you’re finished, select Skip to go back to the System Setup menu.

12

En

Page 11 Page 13
Image 12
Page 11 Page 13
Contents VSX-1014TX Wash hands after handling Information to UserImportant Safety Instructions Contents Other Settings Controlling the rest of your systemOther connections Additional informationFeatures Before you startBefore you start Chapter Checking what’s in the boxInstalling the receiver Before you start VentilationLoading the batteries Minute guide 02 5 minute guide ChapterIntroduction to home theater Listening to Surround SoundPowered subwoofer Minute guideFront speakers Surround speakers02 5 minute guide Make sure ‘Normal SB’ is selected then press EnterFollow the instructions on-screen Checking the settings on your DVD or other player Other problems when using the Auto Mcacc SetupPlaying a source Connecting up Connecting up ChapterAbout cable types Connecting up About the video converterConnecting up Connecting digital audio components Satellite tuner CD recorder DVD or LD player CD playerConnecting up Connecting analog audio components Connecting multichannel analog componentsTip Connecting up Connecting video components Connecting to the front panel video terminalVideo Camera Connecting up Connecting antennas FM wire antennaUsing external antennas AM loop antennaConnecting the speakers Front speakersOverhead view of speaker setup Hints on speaker placementConnecting up Power cord cautionView of 7.1 channel speaker setup AC outletListening Mode Select Controls and displaysControls and displays Chapter Front panelControls and displays Controls and displays Display Stereo MonoTuned SleepControls and displays Remote control 6TUNE/ST +/- /ENTER DTV ON/OFFDTV Info Tuner DisplayOperating range of remote control unit Listening to your system Listening to your system ChapterListening in surround sound Auto playbackUsing the Home THX modes Using the Advanced surround effectsListening to your system PRO LogicDolby Pro Logic IIx Music settings Neo6 Music settingsUse the +/- buttons to adjust the setting Press EFFECT/CH SEL again to adjust other settingsChoosing the input signal Listening to your system Listening with Acoustic CalibrationType of source Extended Mode Standard / THX Type of source VirtualSB Mode Standard Using the tone controls Press SHIFT+DIALOG E to switch dialog enhancement on or offPress Tone to select the frequency you want to adjust Enhancing dialogUsing the sleep timer Listening to your system Playing other sourcesSelecting the multichannel analog inputs 30 minSystem Setup menu System Setup menu ChapterMaking receiver settings from the System Setup menu Surround back speaker settingSystem Setup menu Manual Mcacc speaker setupSelect the surround back speaker setting Select ‘MANUAL MCACC’ from the System Setup menuFine Channel Level Fine Channel DistanceSetting the Acoustic Calibration EQ automatically Copying your Acoustic Calibration EQ settingsAcoustic Calibration EQ Setting the Acoustic Calibration EQ manually Checking your Acoustic Calibration EQ settingsFront Align Manual speaker setup Select the setting you want to checkSelect ‘Manual SP Setup’ then press Enter Speaker Setting Select ‘Speaker Setting’ from the Manual SP Setup menuCrossover Network Channel LevelSelect ‘Speaker Distance’ from the Manual SP Setup menu Speaker DistanceUsing the tuner Using the tuner ChapterTuning directly to a station Listening to the radioUsing the tuner Saving station presets Naming station presetsListening to station presets AbcdefghijklmnopqrstuvwxyzMaking recordings Making recordings ChapterMaking an audio or a video recording Prepare the recorderSetting the remote to control other components Selecting preset codes directlyControlling the rest of your system Controlling the rest of your system ChapterUse cursor left/right to select Learn then press Enter Press the Receiver button to exit and store the operationsErasing all of the remote control presets Confirming preset codesDirect function Controlling the rest of your system Controls for TVs InputSelect DiscCD/MD/CD-R/DVD/LD SHIFT+Controlling the rest of your system Enter GuideHDD Shift + DVDSecond Zone speaker B setup Switching the speaker systemOther connections Other connections ChapterBi-wiring your speakers Other connections Bi-amping your front speakersFront left Speaker Other connections Connecting additional amplifiers Using this receiver with a Pioneer plasma displayUsing the SR+ mode with a Pioneer plasma display Other connectionsDVD player Other Settings Other Settings ChapterInput Assign menu Assigning the digital inputsOther Settings Other Setup menuAssigning the component video inputs Dynamic Range Control Setup Dual Mono SetupSelect ‘DRC Setup’ from the Other Setup menu Choose the setting that you wantLFE Attenuator Setup SR+ Setup for Pioneer plasma displaysSelect ‘LFE ATT Setup’ from the Other Setup menu Select ‘SR+ Setup’ from the Other Setup menuTroubleshooting PowerAdditional information Additional information ChapterAdditional information No soundOther audio problems Digital inputs onVideo Audio components onSettings DisplayRemote control Control unit onAdditional information Resetting the main unit Switching the speaker impedancePress System Setup to confirm Additional information Surround sound formats DolbyAdditional information About THX Additional information Specifications Cleaning the unitTo establish a safe level Once you have established a comfortable sound levelDecibel Level Example Pioneer Corporation

VSX-1014TX specifications

The Pioneer VSX-1014TX is a feature-rich AV receiver that has made a mark in the home theater market, thanks to its impressive performance and versatility. Designed for movie enthusiasts and music lovers alike, this receiver packs a punch with a wide array of technologies and features that enhance the audio and visual experience.

One of the standout features of the VSX-1014TX is its powerful amplification. With 100 watts per channel across seven channels, it delivers a robust performance that is capable of driving demanding speakers to their full potential. This ensures that every sound detail is reproduced with clarity, whether it's a quiet dialogue or the explosive sound effects of an action-packed film.

Equipped with Dolby Digital EX and DTS-ES decoding, the VSX-1014TX provides an immersive surround sound experience. It supports multiple audio formats, allowing users to enjoy high-quality audio from DVDs, Blu-rays, and streaming services. The receiver also features DTS Neo:6 and Pro Logic IIx, which can up-mix stereo content to impressive surround sound, giving new life to older music and movies.

Another significant feature is the inclusion of Pioneer's Multi-Channel Acoustic Calibration System (MCACC). This technology automatically analyzes the acoustics of the room and adjusts the receiver's settings accordingly. This means that whether you have a dedicated home theater or a simple living room setup, the VSX-1014TX ensures optimal sound quality tailored to your specific environment.

The connectivity options on the VSX-1014TX are extensive. It includes multiple HDMI inputs, component video inputs, and digital audio inputs, providing flexibility for various devices. The receiver is also compatible with high-definition audio formats, ensuring that users can enjoy the latest advancements in sound technology.

For added convenience, the VSX-1014TX features an intuitive on-screen display, making navigation through its settings straightforward. This, coupled with its customizable remote control, allows users to easily manage their home theater setup.

In summary, the Pioneer VSX-1014TX is an exceptional AV receiver that blends powerful performance with cutting-edge technology. Its robust amplification, immersive surround sound capabilities, intelligent calibration system, and extensive connectivity make it an ideal choice for anyone looking to elevate their audio-visual experience at home. Whether you're watching a movie or enjoying your favorite music, the VSX-1014TX is designed to deliver an engaging and high-quality experience.
Top Page Image Contents