Pioneer VSX-1014TX manual Settings, Display

Page 68

12Additional information

Settings

Symptom

Cause

The Auto MCACC Setup

• The ambient noise level in the room is too

continually shows an error.

high, or obstacles are blocking the setup

 

microphone.

Remedy

•Keep the noise level in the room as low as possible when using the Auto MCACC Setup (see Other problems when using the Auto MCACC Setup on page 13 for more on this). If the noise cannot be kept low enough, you will have to set up the surround sound manually (page 43).

After using the Auto MCACC Setup, the speaker size setting (LARGE or SMALL) is incorrect.

•There was some inaudible low-frequency noise in the room.

•The low-frequency noise could have been caused by an air conditioner or motor. Switch off all appliances in the room and rerun the Auto MCACC Setup.

Display

Symptom

Cause

Remedy

The display is dark or off.

• The display is set to dark or off.

•Press FL. DIMMER on the remote control repeatedly to select a different brightness.

After making an adjustment the

• The display is set to off.

• Press FL. DIMMER on the remote control repeatedly to

display goes off.

 

select a different brightness.

 

 

 

You can't get DIGITAL to display

• There is a problem with the digital

• Check your digital connections and/or assign the digital

when using the SIGNAL SELECT

connections or the digital input is assigned

inputs correctly (see Assigning the digital inputs on

button.

incorrectly.

page 60).

 

 

 

 

• The multichannel analog inputs are

• Press MULTI CH IN again (see Selecting the

 

selected.

multichannel analog inputs on page 37).

 

 

 

The Dolby/DTS indicator doesn't

• The player is paused.

• Press play.

light when playing Dolby/DTS

 

 

• The player's sound output settings are

• Set the player correctly (consult the manual that came

software.

wrong.

with the player, if necessary).

 

 

 

 

When playing a DVD-Audio disc,

• The audio from these discs is output from

• This is not a malfunction. See also the operating

the DVD player display shows 96

the analog audio jacks of the DVD player only;

instructions that came with your DVD player.

kHz. However, the receiver’s

the receiver does not show the sampling rate

 

display does not.

of the input signal through the analog inputs.

 

 

 

 

During playback of a DTS 96/24

• The receiver’s input signal type is set to

• Set the receiver to AUTO or DIGITAL (see Choosing the

source, the display doesn't show

analog.

input signal on page 33).

96kHz.

 

 

 

 

 

When playing Dolby Digital or

• No digital connection, or the digital

• Check the digital audio connection (page 16).

DTS sources, the receiver’s

connection is incorrect.

 

format indicators do not light.

 

 

• The receiver’s input signal type is set to

• Set the receiver to AUTO or DIGITAL (see Choosing the

 

 

analog.

input signal on page 33).

 

 

 

 

• The DVD player is set to output Dolby Digital

• Check the settings on the player. Set the output for

 

and/or DTS audio as PCM.

Dolby Digital and DTS (no PCM conversion). See also the

 

 

operating instructions that came with your DVD player.

 

 

 

 

• The disc has several playback audio tracks;

• Switch the playback audio channel on your DVD player.

 

the one currently playing is actually PCM.

See the operating instructions that came with your DVD

 

 

player.

 

 

 

When playing certain discs,

• The audio format of the disc is not 5.1/6.1

• This is not a malfunction. Check the disc packaging for

none of the receiver’s format

channel.

details of the audio formats available on the disc.

indicators light.

 

 

 

 

 

When playing a disc, the

• The input signal type is set to analog.

• Set the receiver to AUTO or DIGITAL (see Choosing the

2 PL II or Neo:6 indicator lights

 

input signal on page 33).

on the receiver.

 

 

• A two channel soundtrack is currently

• This is not a malfunction. Check the disc packaging for

 

 

playing.

details of the audio formats available on the disc.

 

 

 

 

• The soundtrack currently playing is

• This is not a malfunction. Check the disc packaging for

 

encoded using Dolby Surround.

details of the audio formats available on the disc.

 

 

 

During playback of a Surround

•The source may be Dolby Surround EX / DTS

• Set to Extended ON (see Using the surround back

EX or DTS ES source on the

ES software, but it has no flag to indicate it is

channel (Extended mode) on page 34) then switch to the

Extended AUTO setting, the EX

6.1 compatible.

THX Surround EX or Standard EX listening mode (see

and ES indicators don’t light, or

 

Listening in surround sound on page 30).

the signal is not properly

 

 

processed.

 

 

 

 

 

68

En

Page 67 Page 69
Image 68
Page 67 Page 69
Contents VSX-1014TX Wash hands after handling Information to UserImportant Safety Instructions Contents Other Settings Controlling the rest of your systemOther connections Additional informationFeatures Before you startBefore you start Chapter Checking what’s in the boxLoading the batteries Installing the receiverBefore you start Ventilation Minute guide 02 5 minute guide ChapterIntroduction to home theater Listening to Surround SoundPowered subwoofer Minute guideFront speakers Surround speakers02 5 minute guide Make sure ‘Normal SB’ is selected then press EnterFollow the instructions on-screen Playing a source Checking the settings on your DVD or other playerOther problems when using the Auto Mcacc Setup About cable types Connecting upConnecting up Chapter Connecting up About the video converterConnecting up Connecting digital audio components Satellite tuner CD recorder DVD or LD player CD playerTip Connecting up Connecting analog audio componentsConnecting multichannel analog components Video Camera Connecting up Connecting video componentsConnecting to the front panel video terminal Connecting up Connecting antennas FM wire antennaUsing external antennas AM loop antennaConnecting the speakers Front speakersOverhead view of speaker setup Hints on speaker placementConnecting up Power cord cautionView of 7.1 channel speaker setup AC outletListening Mode Select Controls and displaysControls and displays Chapter Front panelControls and displays Controls and displays Display Stereo MonoTuned SleepControls and displays Remote control 6TUNE/ST +/- /ENTER DTV ON/OFFDTV Info Tuner DisplayOperating range of remote control unit Listening to your system Listening to your system ChapterListening in surround sound Auto playbackUsing the Home THX modes Using the Advanced surround effectsListening to your system PRO LogicDolby Pro Logic IIx Music settings Neo6 Music settingsUse the +/- buttons to adjust the setting Press EFFECT/CH SEL again to adjust other settingsChoosing the input signal Listening to your system Listening with Acoustic CalibrationType of source Extended Mode Standard / THX Type of source VirtualSB Mode Standard Using the tone controls Press SHIFT+DIALOG E to switch dialog enhancement on or offPress Tone to select the frequency you want to adjust Enhancing dialogUsing the sleep timer Listening to your system Playing other sourcesSelecting the multichannel analog inputs 30 minSystem Setup menu System Setup menu ChapterMaking receiver settings from the System Setup menu Surround back speaker settingSystem Setup menu Manual Mcacc speaker setupSelect the surround back speaker setting Select ‘MANUAL MCACC’ from the System Setup menuFine Channel Level Fine Channel DistanceAcoustic Calibration EQ Setting the Acoustic Calibration EQ automaticallyCopying your Acoustic Calibration EQ settings Front Align Setting the Acoustic Calibration EQ manuallyChecking your Acoustic Calibration EQ settings Select ‘Manual SP Setup’ then press Enter Manual speaker setupSelect the setting you want to check Speaker Setting Select ‘Speaker Setting’ from the Manual SP Setup menuCrossover Network Channel LevelSelect ‘Speaker Distance’ from the Manual SP Setup menu Speaker DistanceUsing the tuner Using the tuner ChapterTuning directly to a station Listening to the radioUsing the tuner Saving station presets Naming station presetsListening to station presets AbcdefghijklmnopqrstuvwxyzMaking recordings Making recordings ChapterMaking an audio or a video recording Prepare the recorderSetting the remote to control other components Selecting preset codes directlyControlling the rest of your system Controlling the rest of your system ChapterUse cursor left/right to select Learn then press Enter Press the Receiver button to exit and store the operationsDirect function Erasing all of the remote control presetsConfirming preset codes Controlling the rest of your system Controls for TVs InputSelect DiscCD/MD/CD-R/DVD/LD SHIFT+Controlling the rest of your system Enter GuideHDD Shift + DVDSecond Zone speaker B setup Switching the speaker systemOther connections Other connections ChapterFront left Speaker Bi-wiring your speakersOther connections Bi-amping your front speakers Other connections Connecting additional amplifiers Using this receiver with a Pioneer plasma displayDVD player Using the SR+ mode with a Pioneer plasma displayOther connections Other Settings Other Settings ChapterInput Assign menu Assigning the digital inputsAssigning the component video inputs Other SettingsOther Setup menu Dynamic Range Control Setup Dual Mono SetupSelect ‘DRC Setup’ from the Other Setup menu Choose the setting that you wantLFE Attenuator Setup SR+ Setup for Pioneer plasma displaysSelect ‘LFE ATT Setup’ from the Other Setup menu Select ‘SR+ Setup’ from the Other Setup menuTroubleshooting PowerAdditional information Additional information ChapterAdditional information No soundOther audio problems Digital inputs onVideo Audio components onSettings DisplayRemote control Control unit onPress System Setup to confirm Additional information Resetting the main unitSwitching the speaker impedance Additional information Surround sound formats DolbyAdditional information About THX Additional information Specifications Cleaning the unitDecibel Level Example To establish a safe levelOnce you have established a comfortable sound level Pioneer Corporation

VSX-1014TX specifications

The Pioneer VSX-1014TX is a feature-rich AV receiver that has made a mark in the home theater market, thanks to its impressive performance and versatility. Designed for movie enthusiasts and music lovers alike, this receiver packs a punch with a wide array of technologies and features that enhance the audio and visual experience.

One of the standout features of the VSX-1014TX is its powerful amplification. With 100 watts per channel across seven channels, it delivers a robust performance that is capable of driving demanding speakers to their full potential. This ensures that every sound detail is reproduced with clarity, whether it's a quiet dialogue or the explosive sound effects of an action-packed film.

Equipped with Dolby Digital EX and DTS-ES decoding, the VSX-1014TX provides an immersive surround sound experience. It supports multiple audio formats, allowing users to enjoy high-quality audio from DVDs, Blu-rays, and streaming services. The receiver also features DTS Neo:6 and Pro Logic IIx, which can up-mix stereo content to impressive surround sound, giving new life to older music and movies.

Another significant feature is the inclusion of Pioneer's Multi-Channel Acoustic Calibration System (MCACC). This technology automatically analyzes the acoustics of the room and adjusts the receiver's settings accordingly. This means that whether you have a dedicated home theater or a simple living room setup, the VSX-1014TX ensures optimal sound quality tailored to your specific environment.

The connectivity options on the VSX-1014TX are extensive. It includes multiple HDMI inputs, component video inputs, and digital audio inputs, providing flexibility for various devices. The receiver is also compatible with high-definition audio formats, ensuring that users can enjoy the latest advancements in sound technology.

For added convenience, the VSX-1014TX features an intuitive on-screen display, making navigation through its settings straightforward. This, coupled with its customizable remote control, allows users to easily manage their home theater setup.

In summary, the Pioneer VSX-1014TX is an exceptional AV receiver that blends powerful performance with cutting-edge technology. Its robust amplification, immersive surround sound capabilities, intelligent calibration system, and extensive connectivity make it an ideal choice for anyone looking to elevate their audio-visual experience at home. Whether you're watching a movie or enjoying your favorite music, the VSX-1014TX is designed to deliver an engaging and high-quality experience.
Top Page Image Contents