Pioneer VSX-1014TX manual Additional information Chapter, Troubleshooting, Power

Page 64

12Additional information

Chapter 12:

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized independent service company to carry out repair work.

Power

Symptom

Cause

Remedy

The power does not turn on.

• The power plug is disconnected.

• Connect the power plug to the wall outlet.

• The protection circuit may have been

• Disconnect the power plug from the outlet, and insert

activated.

again.

The receiver suddenly switches

• The speaker wires are frayed or sticking out

• Reinsert the speaker wires, making sure there are no

off.

of the jack, and are touching the back of the

stray strands of wire and that they are inserted fully.

 

receiver or another set of wires.

 

 

 

 

 

• The receiver has a serious problem.

• Unplug the receiver from the wall and call a Pioneer

 

 

authorized independent service company.

During loud playback the power suddenly switches off.

•The protection circuit has been activated because the lowest actual impedance of the speakers (as opposed to the speakers rated impedance) is dangerously low.

•Turn down the volume.

•When it’s convenient, go to Acoustic Calibration EQ on page 41 and lower the 40 Hz and 125 Hz equalizer levels using the manual setting.

•Turning the digital safety feature on may allow you to turn up the volume a little more. To switch between SAFETY ON and SAFETY OFF, put the receiver into standby, then press the STANDBY/ON button while holding down the SYSTEM SETUP button on the front panel.

The unit does not respond when • Static electricity caused by dry air. the buttons are pressed.

•Switch the unit off, then on again.

•Disconnect the power plug from the outlet, and insert again.

AMP ERR blinks in the display, • The receiver has a serious problem. then the power automatically

switches off. The MCACC blinks and the power does not turn on.

•Do not try to turn on the receiver. Contact a Pioneer authorized independent service company for assistance.

OVERHEAT blinks in the display then the power automatically switches off.

•The internal temperature of the unit has become too high.

•After allowing the unit to cool down in a well-ventilated place, try switching the receiver back on. Make sure you follow the guidelines for improving heat dispersal in Ventilation on page 7.

64

En

Page 63 Page 65
Image 64
Page 63 Page 65
Contents VSX-1014TX Wash hands after handling Information to UserImportant Safety Instructions Contents Other Settings Controlling the rest of your systemOther connections Additional informationFeatures Before you startBefore you start Chapter Checking what’s in the boxBefore you start Ventilation Installing the receiverLoading the batteries Minute guide 02 5 minute guide ChapterIntroduction to home theater Listening to Surround SoundPowered subwoofer Minute guideFront speakers Surround speakers02 5 minute guide Make sure ‘Normal SB’ is selected then press EnterFollow the instructions on-screen Other problems when using the Auto Mcacc Setup Checking the settings on your DVD or other playerPlaying a source Connecting up Chapter Connecting upAbout cable types Connecting up About the video converterConnecting up Connecting digital audio components Satellite tuner CD recorder DVD or LD player CD playerConnecting multichannel analog components Connecting up Connecting analog audio componentsTip Connecting to the front panel video terminal Connecting up Connecting video componentsVideo Camera Connecting up Connecting antennas FM wire antennaUsing external antennas AM loop antennaConnecting the speakers Front speakersOverhead view of speaker setup Hints on speaker placementConnecting up Power cord cautionView of 7.1 channel speaker setup AC outletListening Mode Select Controls and displaysControls and displays Chapter Front panelControls and displays Controls and displays Display Stereo MonoTuned SleepControls and displays Remote control 6TUNE/ST +/- /ENTER DTV ON/OFFDTV Info Tuner DisplayOperating range of remote control unit Listening to your system Listening to your system ChapterListening in surround sound Auto playbackUsing the Home THX modes Using the Advanced surround effectsListening to your system PRO LogicDolby Pro Logic IIx Music settings Neo6 Music settingsUse the +/- buttons to adjust the setting Press EFFECT/CH SEL again to adjust other settingsChoosing the input signal Listening to your system Listening with Acoustic CalibrationType of source Extended Mode Standard / THX Type of source VirtualSB Mode Standard Using the tone controls Press SHIFT+DIALOG E to switch dialog enhancement on or offPress Tone to select the frequency you want to adjust Enhancing dialogUsing the sleep timer Listening to your system Playing other sourcesSelecting the multichannel analog inputs 30 minSystem Setup menu System Setup menu ChapterMaking receiver settings from the System Setup menu Surround back speaker settingSystem Setup menu Manual Mcacc speaker setupSelect the surround back speaker setting Select ‘MANUAL MCACC’ from the System Setup menuFine Channel Level Fine Channel DistanceCopying your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ automaticallyAcoustic Calibration EQ Checking your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ manuallyFront Align Select the setting you want to check Manual speaker setupSelect ‘Manual SP Setup’ then press Enter Speaker Setting Select ‘Speaker Setting’ from the Manual SP Setup menuCrossover Network Channel LevelSelect ‘Speaker Distance’ from the Manual SP Setup menu Speaker DistanceUsing the tuner Using the tuner ChapterTuning directly to a station Listening to the radioUsing the tuner Saving station presets Naming station presetsListening to station presets AbcdefghijklmnopqrstuvwxyzMaking recordings Making recordings ChapterMaking an audio or a video recording Prepare the recorderSetting the remote to control other components Selecting preset codes directlyControlling the rest of your system Controlling the rest of your system ChapterUse cursor left/right to select Learn then press Enter Press the Receiver button to exit and store the operationsConfirming preset codes Erasing all of the remote control presetsDirect function Controlling the rest of your system Controls for TVs InputSelect DiscCD/MD/CD-R/DVD/LD SHIFT+Controlling the rest of your system Enter GuideHDD Shift + DVDSecond Zone speaker B setup Switching the speaker systemOther connections Other connections ChapterOther connections Bi-amping your front speakers Bi-wiring your speakersFront left Speaker Other connections Connecting additional amplifiers Using this receiver with a Pioneer plasma displayOther connections Using the SR+ mode with a Pioneer plasma displayDVD player Other Settings Other Settings ChapterInput Assign menu Assigning the digital inputsOther Setup menu Other SettingsAssigning the component video inputs Dynamic Range Control Setup Dual Mono SetupSelect ‘DRC Setup’ from the Other Setup menu Choose the setting that you wantLFE Attenuator Setup SR+ Setup for Pioneer plasma displaysSelect ‘LFE ATT Setup’ from the Other Setup menu Select ‘SR+ Setup’ from the Other Setup menuTroubleshooting PowerAdditional information Additional information ChapterAdditional information No soundOther audio problems Digital inputs onVideo Audio components onSettings DisplayRemote control Control unit onSwitching the speaker impedance Additional information Resetting the main unitPress System Setup to confirm Additional information Surround sound formats DolbyAdditional information About THX Additional information Specifications Cleaning the unitOnce you have established a comfortable sound level To establish a safe levelDecibel Level Example Pioneer Corporation

VSX-1014TX specifications

The Pioneer VSX-1014TX is a feature-rich AV receiver that has made a mark in the home theater market, thanks to its impressive performance and versatility. Designed for movie enthusiasts and music lovers alike, this receiver packs a punch with a wide array of technologies and features that enhance the audio and visual experience.

One of the standout features of the VSX-1014TX is its powerful amplification. With 100 watts per channel across seven channels, it delivers a robust performance that is capable of driving demanding speakers to their full potential. This ensures that every sound detail is reproduced with clarity, whether it's a quiet dialogue or the explosive sound effects of an action-packed film.

Equipped with Dolby Digital EX and DTS-ES decoding, the VSX-1014TX provides an immersive surround sound experience. It supports multiple audio formats, allowing users to enjoy high-quality audio from DVDs, Blu-rays, and streaming services. The receiver also features DTS Neo:6 and Pro Logic IIx, which can up-mix stereo content to impressive surround sound, giving new life to older music and movies.

Another significant feature is the inclusion of Pioneer's Multi-Channel Acoustic Calibration System (MCACC). This technology automatically analyzes the acoustics of the room and adjusts the receiver's settings accordingly. This means that whether you have a dedicated home theater or a simple living room setup, the VSX-1014TX ensures optimal sound quality tailored to your specific environment.

The connectivity options on the VSX-1014TX are extensive. It includes multiple HDMI inputs, component video inputs, and digital audio inputs, providing flexibility for various devices. The receiver is also compatible with high-definition audio formats, ensuring that users can enjoy the latest advancements in sound technology.

For added convenience, the VSX-1014TX features an intuitive on-screen display, making navigation through its settings straightforward. This, coupled with its customizable remote control, allows users to easily manage their home theater setup.

In summary, the Pioneer VSX-1014TX is an exceptional AV receiver that blends powerful performance with cutting-edge technology. Its robust amplification, immersive surround sound capabilities, intelligent calibration system, and extensive connectivity make it an ideal choice for anyone looking to elevate their audio-visual experience at home. Whether you're watching a movie or enjoying your favorite music, the VSX-1014TX is designed to deliver an engaging and high-quality experience.
Top Page Image Contents