Pioneer VSX-1014TX manual Video, Audio components on

Page 67

Additional information

12

Symptom

Cause

Remedy

Can't record audio.

• You are trying to make an analog recording

• You can only record analog to analog, or digital to

 

from a digital signal, or a digital recording of

digital.

 

an analog source.

 

 

 

 

 

• The digital source is copy protected.

• You can't record digital sources that have been copy

 

 

protected.

 

 

 

 

• The analog REC jacks have not been

• Check your analog connections (see Connecting analog

 

connected properly.

audio components on page 17).

 

 

 

Subwoofer output is very low.

• The speaker settings result in very little

• To route more audio signal to the subwoofer, set it to

 

audio signal being sent to the subwoofer.

PLUS, or select SMALL for the front speaker setting (see

 

 

Speaker Setting on page 44).

Everything seems to be set up

• The speakers are out of phase.

correctly, but the playback sound

 

is odd.

 

•Check that the positive/negative speaker terminals on the receiver are matched with the corresponding terminals on the speakers (see Connecting the speakers on page 20).

Noise or hum can be heard even

• There is electrical interference from another

• Check that personal computers or other digital

when there is no sound being

component or appliance.

components connected to the same power source are not

input.

 

causing interference.

 

 

 

There seems to be a time lag

• The subwoofer channel can be delayed

• See Automatically setting up for surround sound

between the speakers and the

slightly if run through a low-pass filter.

(MCACC) on page 11 to set up your system again using

output of the subwoofer.

 

MCACC (this will automatically compensate for a delay in

 

 

the subwoofer output).

 

 

The maximum volume available

• The channel levels may have been adjusted. • This is not a malfunction. If the levels in Channel Level

(shown in the front panel display)

 

on page 45 have been adjusted, the maximum volume will

is lower than the +12dB

 

change accordingly.

maximum.

 

 

 

 

 

Video

Symptom

Cause

Remedy

 

 

 

No image is output when an input is selected.

• The video connections are incorrect.

•Make sure the video component is connected correctly (see page 18).

•You are using component video connections for your source, but not for your TV.

•Using the video converter, video signals can be converted from a composite or S-video input to a component video output, but not vice-versa. See About the video converter on page 15 for more on this.

 

• You are using component video

• Check Assigning the component video inputs on page 61

 

connections and the component video inputs

to make sure you’re assigned the correct input.

 

are assigned incorrectly.

 

 

 

 

• The DVD/video player settings are incorrect. • Set correctly. Refer to the instruction manual supplied

 

 

with the DVD/video player.

 

 

 

 

• The video input selected on the TV monitor

• Set correctly. Refer to the instruction manual supplied

 

is incorrect.

with the TV.

 

 

 

 

• The component video inputs are assigned

• Check Assigning the component video inputs on page 61

 

to a video component connected only to the

to make sure the component video assign for that video

 

composite or S-Video terminals.

component is switched to OFF.

 

 

 

The System Setup screen

• Some TVs connected to the receiver with

• When the receiver is in standby, switch to COLOR

doesn't appear.

component video cables do not display the

BURST OFF by holding down the front panel ACOUSTIC

 

System Setup screen when the Color Burst

EQ button and pressing STANDBY/ON. (the current

 

feature is on.

setting appears in the display).

 

 

 

Can’t record video.

• You are trying to record a source connected

• Connect the source component to either the composite

 

to the component video jacks.

video or the S-video jacks (see Connecting video

 

 

components on page 18).

 

 

 

 

• The source is copy protected.

• You can't record sources that have been copy protected.

 

 

 

 

• The recorder's video input is hooked up

• Hook up the source and the recorder using the same

 

using a different type of cable to the source

type of video cable (see About the video converter on

 

video output.

page 15).

 

 

 

67

En

Page 66 Page 68
Image 67
Page 66 Page 68
Contents VSX-1014TX Information to User Wash hands after handlingImportant Safety Instructions Contents Additional information Other SettingsControlling the rest of your system Other connectionsChecking what’s in the box FeaturesBefore you start Before you start ChapterBefore you start Ventilation Installing the receiverLoading the batteries Listening to Surround Sound Minute guide02 5 minute guide Chapter Introduction to home theaterSurround speakers Powered subwooferMinute guide Front speakers02 5 minute guide Enter Make sure ‘Normal SB’ is selected then pressFollow the instructions on-screen Other problems when using the Auto Mcacc Setup Checking the settings on your DVD or other playerPlaying a source Connecting up Chapter Connecting upAbout cable types About the video converter Connecting upSatellite tuner CD recorder DVD or LD player CD player Connecting up Connecting digital audio componentsConnecting multichannel analog components Connecting up Connecting analog audio componentsTip Connecting to the front panel video terminal Connecting up Connecting video componentsVideo Camera AM loop antenna Connecting up Connecting antennasFM wire antenna Using external antennasFront speakers Connecting the speakersHints on speaker placement Overhead view of speaker setupAC outlet Connecting upPower cord caution View of 7.1 channel speaker setupFront panel Listening Mode SelectControls and displays Controls and displays ChapterControls and displays Controls and displays Display Sleep StereoMono TunedControls and displays Remote control Tuner Display 6TUNE/ST +/- /ENTERDTV ON/OFF DTV InfoOperating range of remote control unit Auto playback Listening to your systemListening to your system Chapter Listening in surround soundPRO Logic Using the Home THX modesUsing the Advanced surround effects Listening to your systemPress EFFECT/CH SEL again to adjust other settings Dolby Pro Logic IIx Music settingsNeo6 Music settings Use the +/- buttons to adjust the settingListening to your system Listening with Acoustic Calibration Choosing the input signalType of source Extended Mode Standard / THX Type of source VirtualSB Mode Standard Enhancing dialog Using the tone controlsPress SHIFT+DIALOG E to switch dialog enhancement on or off Press Tone to select the frequency you want to adjust30 min Using the sleep timerListening to your system Playing other sources Selecting the multichannel analog inputsSurround back speaker setting System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuSelect ‘MANUAL MCACC’ from the System Setup menu System Setup menuManual Mcacc speaker setup Select the surround back speaker settingFine Channel Distance Fine Channel LevelCopying your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ automaticallyAcoustic Calibration EQ Checking your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ manuallyFront Align Select the setting you want to check Manual speaker setupSelect ‘Manual SP Setup’ then press Enter Select ‘Speaker Setting’ from the Manual SP Setup menu Speaker SettingChannel Level Crossover NetworkSpeaker Distance Select ‘Speaker Distance’ from the Manual SP Setup menuListening to the radio Using the tunerUsing the tuner Chapter Tuning directly to a stationAbcdefghijklmnopqrstuvwxyz Using the tuner Saving station presetsNaming station presets Listening to station presetsPrepare the recorder Making recordingsMaking recordings Chapter Making an audio or a video recordingControlling the rest of your system Chapter Setting the remote to control other componentsSelecting preset codes directly Controlling the rest of your systemPress the Receiver button to exit and store the operations Use cursor left/right to select Learn then press EnterConfirming preset codes Erasing all of the remote control presetsDirect function Disc Controlling the rest of your system Controls for TVsInput SelectSHIFT+ CD/MD/CD-R/DVD/LDShift + DVD Controlling the rest of your systemEnter Guide HDDOther connections Chapter Second Zone speaker B setupSwitching the speaker system Other connectionsOther connections Bi-amping your front speakers Bi-wiring your speakersFront left Speaker Using this receiver with a Pioneer plasma display Other connections Connecting additional amplifiersOther connections Using the SR+ mode with a Pioneer plasma displayDVD player Assigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuOther Setup menu Other SettingsAssigning the component video inputs Choose the setting that you want Dynamic Range Control SetupDual Mono Setup Select ‘DRC Setup’ from the Other Setup menuSelect ‘SR+ Setup’ from the Other Setup menu LFE Attenuator SetupSR+ Setup for Pioneer plasma displays Select ‘LFE ATT Setup’ from the Other Setup menuAdditional information Chapter TroubleshootingPower Additional informationNo sound Additional informationDigital inputs on Other audio problemsAudio components on VideoDisplay SettingsControl unit on Remote controlSwitching the speaker impedance Additional information Resetting the main unitPress System Setup to confirm Dolby Additional information Surround sound formatsAdditional information About THX Cleaning the unit Additional information SpecificationsOnce you have established a comfortable sound level To establish a safe levelDecibel Level Example Pioneer Corporation

VSX-1014TX specifications

The Pioneer VSX-1014TX is a feature-rich AV receiver that has made a mark in the home theater market, thanks to its impressive performance and versatility. Designed for movie enthusiasts and music lovers alike, this receiver packs a punch with a wide array of technologies and features that enhance the audio and visual experience.

One of the standout features of the VSX-1014TX is its powerful amplification. With 100 watts per channel across seven channels, it delivers a robust performance that is capable of driving demanding speakers to their full potential. This ensures that every sound detail is reproduced with clarity, whether it's a quiet dialogue or the explosive sound effects of an action-packed film.

Equipped with Dolby Digital EX and DTS-ES decoding, the VSX-1014TX provides an immersive surround sound experience. It supports multiple audio formats, allowing users to enjoy high-quality audio from DVDs, Blu-rays, and streaming services. The receiver also features DTS Neo:6 and Pro Logic IIx, which can up-mix stereo content to impressive surround sound, giving new life to older music and movies.

Another significant feature is the inclusion of Pioneer's Multi-Channel Acoustic Calibration System (MCACC). This technology automatically analyzes the acoustics of the room and adjusts the receiver's settings accordingly. This means that whether you have a dedicated home theater or a simple living room setup, the VSX-1014TX ensures optimal sound quality tailored to your specific environment.

The connectivity options on the VSX-1014TX are extensive. It includes multiple HDMI inputs, component video inputs, and digital audio inputs, providing flexibility for various devices. The receiver is also compatible with high-definition audio formats, ensuring that users can enjoy the latest advancements in sound technology.

For added convenience, the VSX-1014TX features an intuitive on-screen display, making navigation through its settings straightforward. This, coupled with its customizable remote control, allows users to easily manage their home theater setup.

In summary, the Pioneer VSX-1014TX is an exceptional AV receiver that blends powerful performance with cutting-edge technology. Its robust amplification, immersive surround sound capabilities, intelligent calibration system, and extensive connectivity make it an ideal choice for anyone looking to elevate their audio-visual experience at home. Whether you're watching a movie or enjoying your favorite music, the VSX-1014TX is designed to deliver an engaging and high-quality experience.
Top Page Image Contents