Pioneer IR Repeater Connections and Remote Control Setup for VSX-D3S

CONNECTIONS

IR REPEATER CONNECTION

Connecting a supplied IR Repeater lets you also control other components with this unit’s remote control.

NOTE:

To operate components not made by Pioneer, perform REMOTE SET UP (page 31) after connecting an IR Repeater.

Remote control signals directed towards this unit or GUI operation signals are transmitted from the repeater as infrared signals, enabling control of other components.

There are two kinds of infrared repeaters. Connect either or both to match the remote control requirements of different components.

MAIN-REPEATER

Use this to operate other components with this unit’s remote control or to operate using GUI on-screen indications.

Install on top of this unit as shown in the figure.

MAIN-REPEATER

CD

VCR

				VIDEO OUT			CONTROL	SYSTEM CONTROL
		GND		TO MONITOR TV					IR OUT
PAL	NTSC						IN	MAIN-
		PHONO						REPEATER
FM 50kHz	100kHz	IN				OUT
/50μS	/75μS					VCR2	OUT
AM 9kHz	10kHz	REC
CHANNEL	STEP					IN	1		2
/FM DE-	EMPHASIS
		TAPE2						MINI-
		MONI-				OUT		REPEATER
		TOR						S
	FM					VCR1
		PLAY						OUT
	BAL
	300Ω REC
						IN		S
								IN
		TAPE1
	FM					LD
	UNBAL							S
	75Ω	PLAY				IN		IN
	GND	CD IN				TV		S	TO
						/SAT			MONITOR
						IN		OUT	TV
	AM	R	L	R	L	VIDEO

SEE INSTRUCTION MANUAL

LOOP

ANTENA

1

2

1Insert the REPEATER’s two pegs into the holes on the top.

2Install the REPEATER laying on its side on the top.

The pegs are usually inserted in the two rear holes.

Use the two front holes when there’s another component on

ANTENNA

MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING CORPORATION. "DOLBY","AC-3", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF DOLBY LABORATORIES LICENSING CORPORATION.

top of this preventing easy reception of the MAIN

Illustration shows Multi-voltage model.

MINI-REPEATER

Use this when a component operates incorrectly after receiving a signal from this unit’s remote control, or when it is difficult for

VSX-D3S

REPEATER’s infrared signals.

acomponent to receive signals from the Main-Repeater. Stick it directly on the remote control sensor window.

There are two MINI-REPEATER terminals.

If you need another Mini-Repeater, contact you nearest Pioneer Service Center.

NOTE:

To prevent possible damage, be careful to avoid accidentally connecting the MINI-REPEATER to the MAIN-REPEATER terminals.

VCR

MINI-REPEATER

VIDEO OUT	CONTROL
	SYSTEM CONTROL
GND	IR OUT

		TO MONITOR TV
PAL	NTSC	IN	MAIN-
			REPEATER

		PHONO
FM 50kHz	100kHz	IN				OUT
/50μS	/75μS					VCR2	OUT
AM 9kHz	10kHz	REC
CHANNEL	STEP					IN 1	2
/FM DE-	EMPHASIS
		TAPE2					MINI-
		MONI-				OUT	REPEATER
		TOR					S
	FM	PLAY				VCR1	OUT
	BAL
	300Ω REC
						IN	S
							IN
		TAPE1
	FM					LD
	UNBAL						S
	75Ω	PLAY				IN	IN
	GND	CD IN				TV		TO	1
						/SAT	S MONITOR
						IN	OUT	TV
				R	L
	AM	R	L			VIDEO

SEE INSTRUCTION MANUAL

LOOP

ANTENA

2

ANTENNA

MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING CORPORATION. "DOLBY","AC-3", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF DOLBY LABORATORIES LICENSING CORPORATION.

1Remove the seal.

Illustration shows Multi-voltage model.

2Stick onto the remote control sensor window.

NOTE:

Before connecting the MAIN-REPEATER or MINI-REPEATER, switch power to the unit OFF, and wait for about one hour. (When power is ON, the rear panel may become very hot.)

10

<ARB7050>