Pioneer VSX-D3S warranty Symptom Cause Remedy No auto stop, VCR’s TV tuner is used

Page 35

		TROUBLESHOOTING

Symptom	Cause	Remedy

No auto stop.	÷ Input signals are not strong enough.	÷ (FM) If the supplied simple antenna is being
		used, change to an outdoor antenna.

TV source cannot be seen when	÷ TV antenna is not connected to the VCR, or	÷ Consult the VCR’s operating instructions, and
the VCR’s TV tuner is used.	connections are faulty.	connect the antenna correctly.
	÷ The VCR’s input switch is set to line input.	÷ Set the VCR’s input switch to built-in tuner.

No rear sound is produced.	÷ The SPEAKER MODE is set incorrectly.	÷ Set correctly.
	÷ The REAR LEVEL is turned down.	÷ Refer to page 30 and adjust the rear level.
	÷ Speaker connecting wires are disconnected	÷ Connect wires to the terminals securely.
	from the REAR SPEAKERS terminals.

Remote control does not work.	÷ Batteries are dead or missing in remote	÷ Insert new batteries.
	control unit.
	÷ Poor angle or too great a distance from the	÷ Use within 7 meters and within a 30 degree angle
	remote sensor window.	of the remote sensor window.
	÷ There is an obstacle between you and the	÷ Change your position or move the obstacle.
	remote sensor window.
	÷ A fluorescent light is shining on the remote	÷ Move the receiver so fluorescent light does not
	sensor window.	shine directly on the receiver’s front panel remote
		sensor window.
	÷ The Main-repeater signal does not reach	÷ Try changing the position of this unit or other
	other components.	units. If the signal still does not reach other
		components, use a supplied Mini-repeater.

Abnormal functioning of this unit may be caused by static electricity or other external interference. To restore normal operation, turn the power off and then on again, or unplug the AC power cord and then plug it in again.

35

<ARB7050>

Image 35

Contents Important Notice Demo ModeReset function AUDIO/VIDEO Stereo ReceiverRisk of Electric Shock Do not Open Information to UserContents Inspection ChecklistFM 50 kHz/50 ∝s, AM 9 kHz position InstallationPAL/NTSC Switch FM 100 kHz/75 ∝s, AM 10 kHz positionPOWER-CORD Caution Installation PrecautionsInstallation Installing the ReceiverGrounding ConnectionsAntenna Connections Outdoor FM AntennaConnections When using a graphic equalizerAudio System Connections Front Panel S-VIDEO ConnectorsHow to use S-VIDEO connectors Video System ConnectionsSpeaker I+II Selector Connecting Two Center Speakers for Dual CenterSpeaker System Connections Speaker cord connectionMAIN-REPEATER IR Repeater ConnectionMAIN-REPEATER MINI-REPEATERRear Panel Facilities ¡ AC Outlets Rear Panel FacilitiesFront Panel Facilities Front Panel Facilities MULTI-JOG Front Panel Facilities Display SectionOperating the Tuner Tuning Into StationsFrequency Presetting Listening to Broadcasts Using Preset TuningOperating the Tuner Operating the AUDIO/VIDEO ComponentsReceiving FM Simulcast TV Programs PlaybackCopying Tapes Using VCR 1, VCR 2 for Audio RecordingRecording with a Cassette Deck Recording with TapeStart recording on the VCR Video RecordingSurround Effect = TV/SATBattery Replacement Remote Control OperationPutting Batteries Into the Remote Control Unit Remote Control RangeOperating Other Components Remote Control OperationReceiver Control Buttons REW button TV Power buttonPower button TV FUNC. function buttonST Station Down button Auto tuningManual tuning FF buttonGUI Operating Using GUIOperating the Tuner GUI Operation MANUAL/AUTO TuningPreset Tuning Frequency PresettingTape Operating Other Components GUI OperationOperating Other Components GUI Operation Copy Operation GUI Operation Using the Video Signal Selector GUI OperationSound Edit Operation GUI Operation Setting the Speaker ModeSound Edit Operation GUI Operation Level and Balance AdjustmentAdjustment using the Test Tone Select the manufacturer of your component Calling up and setting up presetsRemote SET UP GUI Operation Select one of the six Remote SET UP functionsLearning Remote SET UP GUI OperationAfter completing the settings, press the Exit button ONE Touch Operation SET UP GUI OperationTroubleshooting No rear sound is produced Symptom Cause Remedy No auto stopVCR’s TV tuner is used Channel mode Appendix a SpecificationsAppendix B Surround Effect Mode Selection with DSP Digital Signal ProcessorEncoding AC-3 in the Cinema Appendix C Dolby AC-3 SurroundDolby Surround Digital AC-3 Dolby Surround PRO-LOGIC Laser Disc FormatAdvantages of AC-3 Over PRO-LOGIC Appendix C Dolby AC-3 SurroundEIA Maintenance of External Surfaces