Pioneer VSX-516-S/-K Speaker terminals, Hints on speaker placement, Release the tabs

Page 18

04Connecting up

VSX-416 model

1Twist exposed wire strands together.

2Push open the tabs and insert exposed wire.

3Release the tabs.

VSX-516 model

1Twist exposed wire strands together.

2Loosen terminal and insert exposed wire.

3Tighten terminal.

Speaker terminals

Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker terminal. If any of the bare speaker wire is touching the back panel when you switch the unit on, the power may cut off as a safety measure. Use good quality speaker wire to connect the speakers to the receiver.

Caution

These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric shock when connecting or disconnecting the speaker cables, disconnect the power cord before touching any uninsulated parts.

Hints on speaker placement

Speakers are usually designed with a particular placement in mind. Some are designed to be floorstanding, while others should be placed on stands to sound their best. Some should be placed near a wall; others should be placed away from walls. We have provided a few tips on getting the best sound from your speakers (following), but you should also follow the guidelines on placement that the speaker manufacturer provided with your particular speakers to get the most out of them.

18

Place the front left and right speakers at equal distances from the TV.

When placing speakers near the TV, we recommend using magnetically shielded speakers to prevent possible interference, such as discoloration of the picture when the TV is switched on. If you do not have magnetically shielded speakers and notice discoloration of the TV picture, move the speakers farther away from the TV.

Place the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen.

If possible, place the surround speakers slightly above ear level.

Try not to place the surround speakers further away from the listening position than the front and center speakers. Doing so can weaken the surround sound effect.

To achieve the best possible surround sound, install your speakers as shown below. Be sure all speakers are installed securely to prevent accidents and improve sound quality.

Caution

If you choose to install the center speaker on top of the TV, be sure to secure it with putty, or by other suitable means, to reduce the risk of damage or injury resulting from the speaker falling from the TV in the event of external shocks such as earthquakes.

Make sure no exposed speaker wire is touching the rear panel, this may cause the receiver to turn off automatically.

En

Image 18
Contents VSX-416-S/-KVSX-516-S/-K Important the Moulded Plug Risk of Electric Shock Do not OpenVoltage selector Ventilation CautionOperating Environment Contents Before you start Chapter Operating range of remote control unitBefore you start Checking what’s in the boxBefore you start Installing the receiver Introduction to home theater Minute guideMinute guide Chapter Listening to Surround Sound02 5 minute guide Using the Quick Setup Setup MIC jack on the front panel Quick surround sound setupQuick surround sound setup Chapter Connect the microphone to the McaccQuick surround sound setup Other problems during Auto McaccEnter Connecting up Connecting up ChapterMaking cable connections Connecting up Connecting a TV and DVD player Connect the analog audio outputs fromThis receiver to a video input on your TV Connecting up Connecting the multichannel analog outputsConnecting up Connecting other audio components About the WMA9 Pro decoderCD-R, MD, DAT, Tape recorder, etc Connecting other video components DVR, VCR, LD player, etcShaped Connecting up Connecting antennasUsing external antennas PlugConnecting up Connecting the speakers English Deutsch Français ItalianoSpeaker terminals Hints on speaker placementTwist exposed wire strands together Release the tabsSpeaker placement diagrams Following illustrations show a 6.1 channel speaker setup.1Input select buttons Controls and displaysControls and displays Chapter Character display See Display onControls and displays DisplayDTS AutoDigital AnalogInput Select Receiver Remote control VSX-516Input Select ADV.SURRMute Master Volume +Retriever Dialog EREC Stop AccessHDD/DVD Tuner DispControls and displays Remote control VSX-416 Volume +EFFECT/CH SEL DVD/DVR 10 /ENTERDisplay Auto playback Listening to your systemListening to your system Chapter Listening in surround soundPress ‘ADV.SURR’ repeatedly to select a listening mode Using the Advanced surround effectsSetting the effect options Listening to your systemPress EFFECT/CH SEL again to adjust other settings Listening in stereoFor stereo playback Choosing the input signal Using surround back channel processingWhile listening to a source, press Listening to your system Using Virtual Surround Back VSB VSB OFF Virtual Surround Back mode is switched offUsing the Sound Retriever Listening to your system Using Midnight and LoudnessUsing the tone controls Enhancing dialogUsing the System Setup menu System Setup menuSystem Setup menu Chapter Manual Mcacc speaker setupSystem Setup menu Fine Channel LevelFine Speaker Distance Select ‘EQ COPY’ from the Manual Mcacc setup menu Select ‘EQ A. SET’ from the Manual Mcacc setup menuWait for the EQ Auto Setup to finish Acoustic Calibration EQUse Adjust to your likingTo copy ConfirmUsing To check the settings Manual speaker setupSpeaker setting Select SP SET from the SP Setup menuChannel level Input Assign menuCrossover network Speaker DistanceDual Mono Setup Other setup menuDynamic Range Control Setup LFE Attenuator SetupSaving station presets Using the tunerUsing the tuner Chapter Listening to the radioChanging the frequency step Using the tunerListening to station presets Press AM or FM to select the tunerMaking recordings Making recordings ChapterMaking an audio or a video recording Use the number buttons to enter the preset code Setting the remote to control other componentsSelecting preset codes directly Controlling the rest of your systemClearing all the remote control settings Controlling the rest of your system Direct functionControlling the rest of your system Controls for TVs InputSelect Disc Controlling the rest of your systemControls for other components SHIFT+SHIFT+ Audio SHIFT+Enter Guide SHIFT+ HDDDVD Recorder Controlling the rest of your system Preset Code ListOn digital STB Manufacturer CodeTroubleshooting Additional informationAdditional information Chapter Are set for surround back sound Speaker settingsAdditional information Or PlusPress Setup to confirm Additional information Resetting the main unitPower cord caution OK? shows in the displayAdditional information Specifications Cleaning the unit Furnished PartsPioneer Corporation