Pioneer VSX-516-S/-K Additional information Resetting the main unit, Power cord caution

Page 52

11Additional information

Resetting the main unit

Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.

1Switch the receiver into standby.

2While holding down the TONE button,

press and hold the STANDBY/ON button for about three seconds.

3When you see RESET? appear in the display, press the ENTER button.

OK? shows in the display.

4Press SETUP to confirm.

OK appears in the display to indicate that the receiver has been reset to the factory default settings.

Switching the speaker impedance

We recommend using speakers of 8 Ω with this system, but it is possible to switch the imped- ance setting if you plan to use speakers with a 6 Ω impedance rating.

•With the receiver in standby, press the SPEAKER IMPEDANCE button.

Each time you do this, you switch between the impedance settings:

•SP 6 OHM – Use this setting if your speakers are rated at 6 Ω.

•SP 8 OHM – Use this setting if your speakers are rated at 8 Ω or more.

Power cord caution

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or an electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest Pioneer authorized service center or your dealer for a replacement.

52

En

Image 52

Contents VSX-416-S/-KVSX-516-S/-K Important the Moulded Plug Risk of Electric Shock Do not OpenVentilation Caution Voltage selectorOperating Environment Contents Operating range of remote control unit Before you startBefore you start Chapter Checking what’s in the boxBefore you start Installing the receiver Minute guide Minute guide ChapterIntroduction to home theater Listening to Surround Sound02 5 minute guide Using the Quick Setup Quick surround sound setup Quick surround sound setup ChapterSetup MIC jack on the front panel Connect the microphone to the McaccOther problems during Auto Mcacc Quick surround sound setupEnter Connecting up Chapter Connecting upMaking cable connections Connect the analog audio outputs from Connecting up Connecting a TV and DVD playerThis receiver to a video input on your TV Connecting up Connecting the multichannel analog outputsAbout the WMA9 Pro decoder Connecting up Connecting other audio componentsCD-R, MD, DAT, Tape recorder, etc Connecting other video components DVR, VCR, LD player, etcConnecting up Connecting antennas Using external antennasShaped PlugConnecting up Connecting the speakers English Deutsch Français ItalianoHints on speaker placement Twist exposed wire strands togetherSpeaker terminals Release the tabsSpeaker placement diagrams Following illustrations show a 6.1 channel speaker setup.1Controls and displays Controls and displays ChapterInput select buttons Character display See Display onControls and displays DisplayAuto DigitalDTS AnalogRemote control VSX-516 Input SelectInput Select Receiver ADV.SURRMaster Volume + RetrieverMute Dialog EAccess HDD/DVDREC Stop Tuner DispVolume + Controls and displays Remote control VSX-416EFFECT/CH SEL 10 /ENTER DVD/DVRDisplay Listening to your system Listening to your system ChapterAuto playback Listening in surround soundUsing the Advanced surround effects Setting the effect optionsPress ‘ADV.SURR’ repeatedly to select a listening mode Listening to your systemListening in stereo Press EFFECT/CH SEL again to adjust other settingsFor stereo playback Using surround back channel processing Choosing the input signalWhile listening to a source, press Listening to your system Using Virtual Surround Back VSB VSB OFF Virtual Surround Back mode is switched offListening to your system Using Midnight and Loudness Using the tone controlsUsing the Sound Retriever Enhancing dialogSystem Setup menu System Setup menu ChapterUsing the System Setup menu Manual Mcacc speaker setupFine Channel Level System Setup menuFine Speaker Distance Select ‘EQ A. SET’ from the Manual Mcacc setup menu Wait for the EQ Auto Setup to finishSelect ‘EQ COPY’ from the Manual Mcacc setup menu Acoustic Calibration EQAdjust to your liking To copyUse ConfirmManual speaker setup Speaker settingUsing To check the settings Select SP SET from the SP Setup menuInput Assign menu Crossover networkChannel level Speaker DistanceOther setup menu Dynamic Range Control SetupDual Mono Setup LFE Attenuator SetupUsing the tuner Using the tuner ChapterSaving station presets Listening to the radioUsing the tuner Listening to station presetsChanging the frequency step Press AM or FM to select the tunerMaking recordings Chapter Making recordingsMaking an audio or a video recording Setting the remote to control other components Selecting preset codes directlyUse the number buttons to enter the preset code Controlling the rest of your systemClearing all the remote control settings Controlling the rest of your system Direct functionInput Controlling the rest of your system Controls for TVsSelect Controlling the rest of your system Controls for other componentsDisc SHIFT+SHIFT+ Enter GuideSHIFT+ Audio SHIFT+ HDDControlling the rest of your system Preset Code List On digital STBDVD Recorder Manufacturer CodeAdditional information TroubleshootingAdditional information Chapter Speaker settings Additional informationAre set for surround back sound Or PlusAdditional information Resetting the main unit Power cord cautionPress Setup to confirm OK? shows in the displayAdditional information Specifications Cleaning the unit Furnished PartsPioneer Corporation