Mackie CR1604 - VLZ owner manual Tape in Level, Tape to Main MIX, Source, Phones

Page 23

TAPE IN (LEVEL)

This knob controls the level of the stereo signal coming from the TAPE INPUT RCA jacks. Its range is off when fully down, unity at the center detent, with 20dB additional gain turned fully up, which may come in handy if you’ve patched in a “walkperson” type device with wimpy output levels. After the TAPE IN level is determined, the stereo tape signal can be sent to either of two places — the MAIN L-R MIX or the SOURCE matrix .

TAPE TO MAIN MIX

Engaging this switch is just like engaging the L-Rswitch on a channel — the signal, stereo in this case, is sent to the MAIN MIX. It does not interrupt other signals, just adds itself to them. This switch can be very handy in a live sound situation when you want to play soothing elevator music to an anxious crowd.

WARNING: Engaging

TAPE TO MAIN MIX can

create a feedback path be-

tween TAPE INPUT and

TAPE OUTPUT. Make sure your tape deck is not in record, record- pause or input monitor mode when you engage this switch, or that the TAPE IN level knob is turned fully down.

SOURCE

Typically, the engineer sends the main mix to an audience (if live) or to a mixdown deck (if recording). But what if the engineer needs to hear something other than the main mix?

With the New Improved CR1604-VLZ, the engi- neer has several choices of what to listen to. This is one of those tricky parts — have a double espresso first.

Via the SOURCE switches, you can choose to listen to any combination of MAIN MIX, SUBS

Now you know how to select the signals you want to send to the engineer’s control room and/or phones. From there, these signals all pass through the same level control, aptly named:

C-R/PHONES

As you might expect, this knob controls the levels of both the stereo C-R OUTS and PHONES output . The control range is from off through unity gain at the detent, with 10dB of extra gain (when turned fully clockwise).

When MAIN MIX is your SOURCE selection, those signals will now pass through two level controls on the way to your control room amp and headphones — the MAIN L-R MIX fader and this C-R/PHONES knob. This way, you can send a nice healthy level to the MAIN OUT jacks (MAIN L-R MIX fader at “U”), and a qui- eter level to the C-R OUTS or PHONES (C-R/ PHONES knob wherever you like it).

Whatever your selection, you can also use the C-R OUTS for other applications. Its sound quality is just as impeccable as the MAIN OUT outputs. It can be used as additional main mix output and this one will have its own level con- trol. However, should you do this, be aware that if you engage a SOLO switch, that will interrupt the mix, as we’ve already covered .

Once again, engaging a SOLO switch will cause this dramatic turn of events: Any existing SOURCE matrix selections will be replaced by the SOLO signals, appearing at the C-R OUTS, PHONES output and at the meter display. The audible solo levels are controlled by the SOLO level knob. The SOLO levels appearing on the meter display are not controlled by anything

you wouldn’t want that. You want to see the actual channel level on the meter display, regardless of how loud you’re listening.

1-2, SUBS 3-4and TAPE. Selections made in the SOURCE matrix deliver stereo signals to the C-R OUTS, PHONES output and meter display. These signals are tapped after their respective level controls — post-MAINL-R MIX fader, post subgroup faders and post-TAPE IN knob. With no switches engaged, there will be no signal at these outputs and no meter indication, with two exceptions (SOLO / and AUX RETURN 4 ).

One of those exceptions is the SOLO func- tion /. Regardless of the SOURCE matrix selection, engaging a SOLO switch will replace that selection with the SOLO signal, also sent to the C-R OUTS, PHONES output and meter display. This is what makes the Level-Setting Procedure so easy to do.

OO

MAX

C-R / PHONES

TAPE

SUBS 1–2

SUBS 3–4

MAIN MIX

SOURCE

U

 

 

 

 

CLIP

 

 

28

OO +20

 

10

 

 

TAPE IN

 

7

 

 

4

TAPE TO

 

2

MAIN MIX

 

0

 

 

 

 

2

 

 

4

OO MAX

LEVEL

7

SOLO

SET

 

 

 

10

 

 

20

MODE

 

30

 

 

NORMAL (AFL)

RUDE

LEVEL SET (PFL)

SOLO

 

LIGHT

LEFT RIGHT

0 dB=0 dBu

23

Image 23
Contents MIC/LINE Mixer Safety Instructions Other Nuggets of Wisdom LEVEL-SETTING ProcedureRead this Instant MixingArcane Mysteries Illuminated HOW to USE this ManualPlug for the Connectors Section IntroductionContents Hookup Diagrams Stereo EQ Video Setup Switching Positions Converting to Rackmount ModeMIC Inputs Phantom PowerPatchbay Description InterfaceDirect OUT Line InputsTrim InsertOutputs of the multitrack are then Split MonitoringAUX Send Outputs SUB Outs AUX Return InputsTape Input Phones OutputTape Output Mono Output Power ConnectionMain Insert Main OutsPhantom LED Power SwitchPower LED Phantom SwitchAssign 1-2, 3-4, L-R Clean FadeChannel Strip Description FaderDuring Normal AFL mode, the soloed SoloSolo LED OL Mute LEDConstant Loudness MutePAN Stereo SourcesAUX 1, 2, 3 LOW CUTShift PREAssign to Main MIX Output Section DescriptionVLZ MIX Architecture Subgroup FadersPhones Tape in LevelTape to Main MIX SourceRude Solo Light Ment switches post-EQLevel SET LED Solo LevelMeters vs. Reality MetersAUX Talk AUX Sends MasterMain MIX to Subs AUX RET AUX Sends SoloAUX Returns Level Effects to MonitorsReturns Solo Phns only AUX RETPlace the mixer upside-down on a dry, non- marring surface UL WarningMackie Disclaimer About JumpersCR1604-VLZ Source Mod OL Flicker CR1604-VLZ Block DiagramLOW MID High GainSpecifications Repair Service InfoTroubleshooting Aux ChorusingAssign AttenuateDBm DelayConsole CueingEqualization EchoEffects devices EQ curveGround GainGain stage Graphic EQLine level Input moduleKnee LevelPeaking Phantom powerPan, pan pot Parametric EQReturn RCA phono jack-orRCA jack or phono jackRCA phono plug RegenerationSweep EQ VolumeXLR connector Stereo⁄4 TRS Phone Plugs and Jacks XLR ConnectorsAppendix B Connections ⁄4 TS Phone Plugs and JacksSpecial Mackie Connections Switched 1⁄4 Phone JacksRCA Plugs and Jacks Unbalancing a LineTRS Send/Receive Insert Jacks Using the Send Only on an Insert JackMults and Ys Balanced Lines DON’T Phantom Power do & DON’T ChartDon’t use hardware-store light dimmers Do’s and Don’ts of Fixed InstallationsHere are some guidelines Free T-SHIRT OfferSession Date CR1604-VLZ0.5A