Mackie CR1604 - VLZ owner manual Switched 1⁄4 Phone Jacks, RCA Plugs and Jacks, Unbalancing a Line

Page 43

SWITCHED 1⁄4" PHONE JACKS

Switches can be incorporated into 1⁄4" phone jacks, which are activated by inserting the plug. These switches may open an insert loop in a circuit, change the input routing of the signal or serve other functions. Mackie uses switches in the channel insert and bus in- sert jacks, input jacks and AUX returns. We also use these switches to ground the line-level inputs when nothing is plugged into them.

In most cases, the plug must be inserted fully to activate the switch. Mackie takes advantage of this in some circuits, specifying circumstances where you are to insert the plug only partially. See Special Mackie Connections, later in this section.

RCA PLUGS AND JACKS

RCA-type plugs (also known as phono plugs) and jacks are often used in home stereo and video equipment and in many other appli- cations (Figure D). They are unbalanced and electrically identical to a 1⁄4" TS phone plug or jack (See Figure C). Connect the signal to the center post and the ground (earth) or shield to the surrounding “basket.”

UNBALANCING A LINE

In most studio, stage and sound reinforce- ment situations, there is a combination of balanced and unbalanced inputs and outputs on the various pieces of equipment. This usu- ally will not be a problem in making connections.

•When connecting a balanced output to an unbalanced input, be sure the signal high (hot) connections are wired to each other, and that the balanced signal low (cold)

goes to the ground (earth) connection at the unbalanced input. In most cases, the balanced ground (earth) will also be connected to the ground (earth) at the unbalanced input. If there are ground-loop problems, this connection may be left disconnected at the balanced end.

•When connecting an unbalanced output to a balanced input, be sure that the signal high (hot) connections are wired to each other. The unbalanced ground (earth) connection should be wired to the low (cold) and the ground (earth) connections of the balanced input. If there are ground- loop problems, try connecting the unbalanced ground (earth) connection only to the input low (cold) connection, and leaving the input ground (earth) connection disconnected.

In some cases, you will have to make up special adapters to interconnect your equip- ment. For example, you may need a balanced XLR female connected to an unbalanced 1⁄4" TS phone plug.

SPECIAL MACKIE CONNECTIONS

The balanced-to-unbalanced connection has been anticipated in the wiring of Mackie jacks. A 1⁄4" TS plug inserted into a 1⁄4" TRS balanced

 

ring

 

SEND to processor

tip

(TRS plug)

“tip”

sleeve

 

This plug connects to one of the

“ring”

mixer’s Channel Insert jacks.

RETURN from processor

Figure F

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents MIC/LINE Mixer Safety Instructions Other Nuggets of Wisdom LEVEL-SETTING ProcedureRead this Instant MixingArcane Mysteries Illuminated HOW to USE this ManualPlug for the Connectors Section IntroductionContents Hookup Diagrams Stereo EQ Video Setup Switching Positions Converting to Rackmount ModeMIC Inputs Phantom PowerPatchbay Description InterfaceDirect OUT Line InputsTrim InsertAUX Send Outputs Split MonitoringOutputs of the multitrack are then SUB Outs AUX Return InputsTape Output Phones OutputTape Input Mono Output Power ConnectionMain Insert Main OutsPhantom LED Power SwitchPower LED Phantom SwitchAssign 1-2, 3-4, L-R Clean FadeChannel Strip Description FaderDuring Normal AFL mode, the soloed SoloSolo LED OL Mute LEDConstant Loudness MutePAN Stereo SourcesAUX 1, 2, 3 LOW CUTShift PREAssign to Main MIX Output Section DescriptionVLZ MIX Architecture Subgroup FadersPhones Tape in LevelTape to Main MIX SourceRude Solo Light Ment switches post-EQLevel SET LED Solo LevelMeters vs. Reality MetersAUX Talk AUX Sends MasterMain MIX to Subs AUX RET AUX Sends SoloAUX Returns Level Effects to MonitorsReturns Solo Phns only AUX RETPlace the mixer upside-down on a dry, non- marring surface UL WarningMackie Disclaimer About JumpersCR1604-VLZ Source Mod OL Flicker CR1604-VLZ Block DiagramLOW MID High GainSpecifications Troubleshooting Service InfoRepair Aux ChorusingAssign AttenuateDBm DelayConsole CueingEqualization EchoEffects devices EQ curveGround GainGain stage Graphic EQLine level Input moduleKnee LevelPeaking Phantom powerPan, pan pot Parametric EQReturn RCA phono jack-orRCA jack or phono jackRCA phono plug RegenerationSweep EQ VolumeXLR connector Stereo⁄4 TRS Phone Plugs and Jacks XLR ConnectorsAppendix B Connections ⁄4 TS Phone Plugs and JacksSpecial Mackie Connections Switched 1⁄4 Phone JacksRCA Plugs and Jacks Unbalancing a LineTRS Send/Receive Insert Jacks Using the Send Only on an Insert JackMults and Ys Balanced Lines DON’T Phantom Power do & DON’T ChartDon’t use hardware-store light dimmers Do’s and Don’ts of Fixed InstallationsHere are some guidelines Free T-SHIRT OfferSession Date CR1604-VLZ0.5A
Top Page Image Contents