Mackie PPM1012 Features, Rear Panel, Power Switch, SPEAKER-LEVEL Outputs, Ventilation

Page 10

PPM1012

PPM1012 Features

2

3

 

3

2 X 800W PROFESSIONAL POWERED MIXER

 

POWER

SPEAKER OUT

 

SPEAKER OUT

 

A

 

 

B

 

 

 

 

 

 

 

 

 

THIS DEVICE COMPLIES WITH PART 15 OF THE

 

 

 

 

 

FCC RULES AND THE ICES-003 FOR CANADA.

 

 

 

 

 

OPERATION IS SUBJECT TO THE FOLLOWING

AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR

 

 

 

 

TWO CONDITIONS: (1) THIS DEVICE MAY NOT

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC

 

 

 

 

CAUSE HARMFUL INTERFERENCE, AND (2) THIS

 

 

 

 

DEVICE MUST ACCEPT ANY INTERFERENCE

SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR

 

 

 

 

RECEIVED, INCLUDING INTERFERENCE THAT

MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE

 

 

 

 

MAY CAUSE UNDESIRED OPERATION.

PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

 

PIN

PIN

 

 

SERIAL NUMBER

 

 

 

 

 

1+

1+

 

 

 

 

1

1

 

CAUTION

 

1

 

 

 

 

 

 

 

HOT SURFACE,

 

 

 

 

AVOID CONTACT

REVISION

 

 

 

OUTPUT POWER: @ 4 OHMS,

 

 

 

 

800 WATTS PEAK PER CH

 

 

 

 

MINIMUM LOAD: 4 OHMS PER CHANNEL

 

DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA • MANUFACTURED IN CHINA • FABRIQUE EN CHINE • COPYRIGHT ©2008

 

 

"MACKIE" AND THE RUNNING MAN FIGURE ARE TRADEMARKS OF LOUD TECHNOLOGIES, INC. • PATENT PENDING.

 

 

4

 

 

4

 

Rear Panel

 

 

 

convenience: Speakons and 1/4" TS.

 

 

 

 

Two common types of connector are provided for your

1. POWER CONNECTION

 

 

 

• Speakon outputs are wired Pin 1+ positive

 

 

 

(hot) and Pin 1– negative (cold).

This jack accepts the supplied 3-prong IEC AC power

 

 

 

 

 

 

cord.

 

 

 

1–

 

Before you plug the AC power cord into the

 

 

1+

 

 

 

 

 

 

powered mixer, make sure that the voltage of

 

 

 

 

your unit is the same voltage as your local AC

 

 

COLD

1–

 

 

 

mains supply. Use only the power cord supplied. Also,

 

 

 

1+

 

 

HOT

2+

disconnecting the plug’s ground pin is dangerous. Please

 

2–

Mono Speakon Connection

 

don’t do it. And no running with scissors either. Let's be

 

 

safe out there!

 

 

 

• 1/4" TS outputs are wired Tip positive, and

 

 

 

 

2. POWER SWITCH

 

 

 

Sleeve negative.

 

 

 

 

SLEEVE

SLEEVE TIP

 

 

 

 

Press the top of this rocker switch inwards to turn on

 

the mixer. The front panel power LED [42] will glow

TIP

 

with happiness, or at least it will if you have the mixer

TIP

 

plugged into a suitable live AC mains supply.

SLEEVE

Press the bottom of this switch to turn off the mixer, whenever you feel that this would be a safe thing to do.

As a general guide, you should turn on your

powered mixer first, before any external power

amplifiers or powered speakers, and turn it off last. This will reduce the possibilities of any

turn-on, or turn-off thumps in your speakers.

3. SPEAKER-LEVEL OUTPUTS

These output connections provide speaker-level output power from the internal power amplifiers to your passive speakers. The outputs can be selected with the amp mode switch [53] to be either the stereo main mix, mono main mix/monitor 1, or monitor 1/monitor 2.

The power output of the PPM1012 is 500 watts rms per channel into 4 ohms, and 800 watts peak.

1/4" TS Connection

These two types of outputs are wired in parallel, and it is possible to use both types at once.

The minimum impedance that the powered

mixer can handle is 4 ohms per channel, and we recommend that you do not go below this.

If you are using both outputs per channel, make sure each loudspeaker is 8 ohms impedance or greater.

4. VENTILATION

These holes in the rear panel allow the inter-

nal fans to flow breezy and minty-fresh cooling air over the internal power amplifiers. Do not obstruct these holes, or the amplifiers may overheat and

shut down. Do not remove the feet, as these help keep the powered mixer off the ground for ventilation.

10

PPM1012

Image 10
Contents PPM1012 Important Safety Instructions PPM1012Read This To try out your new powered mixer. PleaseDisengage the channels solo switch Play something into that input at real-world levelsHeadphones play main mix, or soloed channels IntroductionContents Hookup Diagrams Microphones Portable RecorderHouse of Worship DJ System Band System Rear Panel PPM1012 FeaturesPower Switch SPEAKER-LEVEL OutputsConnection Section Phantom PowerMIC Inputs MON Send 1 and MON Send Insert Ch toFX Send 1 and FX Send Main Inserts Tape InputsTape Outputs Main OutputsLevel FX Footswitch ConnectorBNC Lamp Connection LUNCH-TIME DecouplerStereo Channels 9/10 and 11/12 Signal FlowChannel Controls Like Unity gainLOW CUT Channels 1-8 only Gain ControlIng levels Compressor Channels 1-6 only Dynamic range is the difference in level beHI-Z Switch Ch and 8 only Channel Equalization EQMON 2 AUX Send High EQ36. FX2 AUX Send 39. -20, 0, +10, OL Channel Meter LEDs Mute switch and LEDPAN Channel FaderAffected by it anyway Never plug single-ended unbalanced Power LEDMaster Controls It is safe to do soMON 1 Equalizer Power AMP Limiter LEDsMain EQ Assign Rude Solo Light Power AMP Mode SwitchMain MIX Meters TapeMono OUT LPF Low-Pass-FilterMost active subwoofers have their own Main Fader FX 1 to MON 1 and FX 1 to MONFX RTN 1 Fader and FX RTN 2 Fader Monitor 1 Fader and Monitor 2 FaderSIG/OL LED Stereo Effects Processors60. FX1 Send Master and FX2 Send Master There are two identical Mackie Running-ManPreset Display Internal FX MuteIs phantom power required for your micro- phones? Appendix a Service InformationTroubleshooting RepairAppendix B Connections XLR ConnectorsRCA Plugs and Jacks Loudspeaker Cable SpeakonsInterrupting normal operation Appendix C Technical Information SpecificationsPPM1012 Block Diagram FX2Appendix D Table of Effects Presets Title Description Example of its usePPM1012 Limited Warranty