Mackie PPM1012 BNC Lamp Connection, Level, LUNCH-TIME Decoupler, FX Footswitch Connector

Page 14

PPM1012

5

6

9

MIC 1

LINE

(BAL/UNBAL)

INSERT

MIC 2

LINE

(BAL/UNBAL)

INSERT

MIC 3

LINE

(BAL/UNBAL)

INSERT

MIC 4

LINE

(BAL/UNBAL)

INSERT

MIC 5

LINE

(BAL/UNBAL)

INSERT

MIC 6

LINE

(BAL/UNBAL)

INSERT

7

MIC 7

HI-Z

LINE

(BAL/UNBAL)

INSERT

MIC 8

7 HI-Z LINE

(BAL/UNBAL)

INSERT

10

 

11

13

14

 

 

 

 

L

 

15

 

1

 

1

 

 

L

2

 

2

R

 

 

R

 

IN

OUT

 

MON SEND

FX SEND

TAPE

 

MAIN INSERT

L

 

L

 

L

 

L

8 (MONO) 8

(MONO) 12

(MONO) 12

(MONO)

R

 

R

 

R

 

R

INPUT 9/10

INPUT 11/12

FX RTN 1

FX RTN 2

L

16 16 L

R

R

17

M

MAIN OUT

M

 

21

LAMP

12V 0.5A

FX

FOOTSWITCH

TIP:FX1

RING:FX2

PHONES

OO

MAX

LEVEL

20

18

19

WARNING: The headphone amp is loud, and

can cause permanent ear damage. Even intermediate levels may be painfully loud with

some earphones. BE CAREFUL! Always turn the phones level control [19] all the way down before connecting headphones or pressing a solo switch, or doing anything new that may affect the headphone volume. Then turn it up slowly as you listen carefully.

21. BNC LAMP CONNECTION

Located in the top right corner of the mixer, this 12V socket will drive any standard BNC-type lamp, for example, a Littlite® #12G or #12G-HI (high-intensity).

It will cast a light in the dark, so you can work your audio magic like an ancient wizard. It will also attract all the mosquitoes, moths, and other hungry flying crit- ters within a one mile radius. Have fun with that.

19. LEVEL

This knob controls the level of the signal going to your stereo headphones.

Make sure this is fully down whenever you are

making connections in your system, or putting on the headphones, or before you press any

solo switch [41]. Bring up the level slowly and carefully to protect your hearing.

22. LUNCH-TIME DECOUPLER

Not available on Earth models, this control actually slows down time, especially lunchtimes. Use this wisely, and only engage it after receiving your food and bever- ages, or you may be in for a long wait.

Do not engage during drum solos or scats.

20. FX FOOTSWITCH CONNECTOR

This is where you connect a footswitch. (Any two-but- ton on/off footswitch will do). This allows you to easily mute or un-mute the two internal effect processors independently, while stamping your foot and looking like you were mad about something.

The output is wired so the tip affects FX1, and the ring affects FX2.

If the internal effects have already been muted with the FX mute switches [64] then the footswitch has no effect. It cannot un-mute or mute it.

The footswitch only affects the internal FX. It has no effect on the output-to and input-from external effects processors.

14

PPM1012

Page 13 Page 15
Image 14
Page 13 Page 15
Contents
PPM1012 Important Safety Instructions PPM1012Read This To try out your new powered mixer. PleaseDisengage the channels solo switch Play something into that input at real-world levelsHeadphones play main mix, or soloed channels IntroductionContents Hookup Diagrams Microphones Portable RecorderHouse of Worship DJ System Band System Rear Panel PPM1012 FeaturesPower Switch SPEAKER-LEVEL OutputsMIC Inputs Phantom PowerConnection Section FX Send 1 and FX Send Insert Ch toMON Send 1 and MON Send Main Inserts Tape InputsTape Outputs Main OutputsLevel FX Footswitch ConnectorBNC Lamp Connection LUNCH-TIME DecouplerStereo Channels 9/10 and 11/12 Signal FlowChannel Controls Like Unity gainIng levels Gain ControlLOW CUT Channels 1-8 only Compressor Channels 1-6 only Dynamic range is the difference in level beHI-Z Switch Ch and 8 only Channel Equalization EQ36. FX2 AUX Send High EQMON 2 AUX Send 39. -20, 0, +10, OL Channel Meter LEDs Mute switch and LEDPAN Channel FaderAffected by it anyway Never plug single-ended unbalanced Power LEDMaster Controls It is safe to do soMain EQ Assign Power AMP Limiter LEDsMON 1 Equalizer Rude Solo Light Power AMP Mode SwitchMain MIX Meters TapeMost active subwoofers have their own LPF Low-Pass-FilterMono OUT Main Fader FX 1 to MON 1 and FX 1 to MONFX RTN 1 Fader and FX RTN 2 Fader Monitor 1 Fader and Monitor 2 FaderSIG/OL LED Stereo Effects Processors60. FX1 Send Master and FX2 Send Master There are two identical Mackie Running-ManPreset Display Internal FX MuteIs phantom power required for your micro- phones? Appendix a Service InformationTroubleshooting RepairRCA Plugs and Jacks XLR ConnectorsAppendix B Connections Interrupting normal operation SpeakonsLoudspeaker Cable Appendix C Technical Information SpecificationsPPM1012 Block Diagram FX2Appendix D Table of Effects Presets Title Description Example of its usePPM1012 Limited Warranty
Related manuals
Manual 36 pages 3.26 Kb