iLive AP7141 manual WDG1 WDG2 IEM1 IEM2, Routing screen

Page 17

Channel MIX view - Sends to all masters from one channel

CHANNEL

STEREO

AUX

IEM1

PAN

MASTERS

IP

1

PAN

L R

CH

FADER

SEL

L R

LEV

AUX

CH PRE

5

ROTARY SHIFT

PRE/POST FADE

STEREOSTEREO

AUX AUX AUX AUX

WDG1

WDG2

IEM1

IEM2

 

 

PAN

PAN

 

L

R L

R

PRE

PRE

PRE

PRE

SEL

SEL

SEL

SEL

3

Current mix status

ON = channel is assigned

PRE = Channel send is set pre- fader.

MIX

1

ASSIGN

MIX

MIX

MIX

MIX

2

 

 

 

Mix sends (Aux, FX, Matrix) may be configured in the ROUTING screen as fader or rotary sends.

Fader mixes Faders = sends from channel Encoders = Pan (if stereo mixes)

Rotary mixes Faders = Masters Encoders = Sends from channels Shifted encoders = Pan

4

1Press a channel strip MIX key Its sends are presented across the master strips.

2 Assign the channels to each master Hold down the ASSIGN key then press master MIX keys to assign to the available mixes. The ON icon displays in the LCDs.

3Set pre or post fader To set the send to each master pre or post-fade, hold down the PRE/POST key and then press master SEL keys.

4Adjust the send levels Aux, FX and matrix mixes can be configured for sends on faders or rotaries. For groups and DCAs (no send levels), the faders and encoders remain unaffected.

5Adjust the image For stereo or multi output main mix use the master encoders to adjust the send Pan. Hold down ROTARY SHIFT and turn the encoder to adjust Pan for stereo mixes with encoder sends.

The ROUTING screen

Turn on the TouchScreen ROUTING page to display the assignment and routing information for the channel or master currently selected using a SEL key. This gives you access to advanced routing options as well as an alternative to using the MIX keys when adjusting sends and assignments.

In this screen you can view and change the channel mix and DCA assignments, fader/pan/aux/matrix send levels, pre/post fade settings and routing options.

Input - Also access the direct output level. Its source is globally set in the MIXRACK SETUP screen.

Aux - Also select the global channel send signal source for each mix from a drop down menu.

Aux, Matrix - Choose to mix sends using the faders or rotary encoders. This can be configured for each mix.

Note - Post-fader sends follow the fader level but get their source as set in this screen.

iLive Fixed Format Getting Started Guide

17

AP7141 iss.2

Image 17
Contents Getting Started Guide Further information Safety InstructionsSystem operating firmware Table of Contents Systems ILive Series IntroductionIDR-48 System componentsIDR-32 IDR-16IEC Series Control layoutPafl Copy/Paste/Reset edit keys Connect Surface to MixRack Network settings Connect and power upACE Network PL-ANETBoot up time Switch power onStatus indicators Status screenLoad a ‘Template Show’ as a starting point Customise and save your settingsLoad a Template Show Recall the layout for your SurfaceDCA TouchScreenGP, FX, AUX, MTX Surface / Preferences Set your operating preferencesChannel Processing view Name and colour channelsName & Colour screen Quick MenuGEQ on faders Access the Preamp, EQ and dynamicsWork with the channel processing IEM2 Work with the mixRouting screen WDG1 WDG2 IEM1 IEM2Tap Tempo Work with the FXUsing the SoftKeys for Mute Groups Using DCA groupsUsing DCAs to create Mute Groups Channel Ganging Copy / Paste / ResetView and patch channel Input sockets Patch the socketsView and patch Output sockets Patching InsertsTo change the Fader Strip Layout Customise your configurationTo change the MIX BUS configuration Power down memory Save your settingsUser Profiles LibrariesScene memories Show memories Monitor System Find out more about using the iLiveSystem example Matrix Main AUX