iLive AP7141 manual Copy/Paste/Reset edit keys

Page 8

R Series Control layout

Soft Keys 8 user assignable keys

Channel Processing Select Press this key to access the processing for the

selected channel using the TouchScreen. Controls for the preamp, EQ, dynamics, delay and insert setup are presented. Use the touch controls and screen rotary to adjust the parameters.

Copy/Paste/Reset edit keys

Hold down then press a SEL or MIX key to copy or reset parameters.

Virtual write-on strip Name, colour and mix status

Fader Banks Two independent groups of fader strips with 6 layers each. Provides control of the Input channel, FX return, Mix master or DCA assigned to it.

TouchScreen keys When these keys are off the screen displays system status. When these keys are off and a strip SEL is active the screen presents the associated channel processing. Use these keys to access system setup and memory management. These override the channel processing view.

Dimmer Talkback Mic Input and level trim. Recessed switch to select 48V phantom power.

Headphones level control

TouchScreen rotary control.

Illuminates orange when it is active.

CLEAR ALL PAFL Press once to clear any active Input PAFL. Press again to clear Output PAFL.

Input PAFL overrides Output PAFL.

Talkback Hold down TB ASSIGN and press master MIX keys to assign.

SEL opens the channel processing for the selected strip in the TouchScreen.

MIX presents the sends for the selected strip on faders (or encoders) and assignments and pre/post settings in the strip LCD windows.

ASSIGN and PRE/POST access keys for the selected mix.

While a MIX is active:

Hold down ASSIGN and press strip MIX keys to toggle the assignments on or off. To assign all use the master MIX key.

Hold down PRE/POST and press strip SEL keys to toggle pre or post fade. To assign all use the master SEL key.

Hold down ROTARY SHIFT to access the second encoder function if it has one.

Hold down ALT VIEW to view the channel or socket numbers instead of name in the LCDs. You can choose to access GAIN using the strip rotaries while the key is pressed.

GEQ FADER FLIP to present the GEQ across the faders.

FREEZE IN LAYERS to keep a channel visible across all layers. Hold down and press strip MIX keys.

Scene GO recall keys. These are disabled by default. Use the SURFACE Preferences option to enable.

SCENE SAFES to prevent selected channels being overwritten by the memories. Hold down SAFES and press MIX keys to toggle on or off.

VGA port for external monitor (same view as TouchScreen).

Lamp socket

For future use…

2x USB ports. Plug your USB key in here.

Surface to MixRack link ACE (audio and control over Ethernet) CAT5 cable up to 120m (400 feet)

Local PAFL

MIDI in

monitor output

and out

IEC mains power input. Plastic clip to secure power cable.

Assignable local audio inputs and outputs. Row A = inputs. Row B = outputs.

Balanced TRS jack line level RCA phono line level

Additional Ethernet ports for connecting

System hard

laptops and wireless router.

reset jumpers

SPDIF digital (2 channel)

iLive Fixed Format Getting Started Guide

8

AP7141 iss.2

Image 8
Contents Getting Started Guide Further information Safety InstructionsSystem operating firmware Table of Contents Systems Introduction ILive SeriesSystem components IDR-48IDR-32 IDR-16IEC Series Control layoutPafl Copy/Paste/Reset edit keys Connect and power up Connect Surface to MixRack Network settingsACE Network PL-ANETSwitch power on Boot up timeStatus indicators Status screenCustomise and save your settings Load a ‘Template Show’ as a starting pointLoad a Template Show Recall the layout for your SurfaceDCA TouchScreenGP, FX, AUX, MTX Set your operating preferences Surface / PreferencesName and colour channels Channel Processing viewName & Colour screen Quick MenuGEQ on faders Access the Preamp, EQ and dynamicsWork with the channel processing Work with the mix IEM2WDG1 WDG2 IEM1 IEM2 Routing screenWork with the FX Tap TempoUsing the SoftKeys for Mute Groups Using DCA groupsUsing DCAs to create Mute Groups Copy / Paste / Reset Channel GangingPatch the sockets View and patch channel Input socketsView and patch Output sockets Patching InsertsTo change the Fader Strip Layout Customise your configurationTo change the MIX BUS configuration Save your settings Power down memoryUser Profiles LibrariesScene memories Show memories Monitor System Find out more about using the iLiveSystem example AUX Matrix Main