Peavey 3120 manual Footswitch, Specifications, Power Amplifier Section, Preamp Section

Page 8

Footswitch

1

LEAD

CLEAN

EFFECTS

LEAD/RHYTHM

BYPASS

BYPASS

2

3

4

1CABLE CONNECTOR

This 7-pin DIN connector is provided for connecting the footswitch to the amplifier RE- MOTE SWITCH (20) via the cable included in the carton. Connections at the switch and the amplifier should be made before the amp is powered up.

2LEAD/RHYTHM SELECTOR

This switch selects between the Rhythm and Lead channels on the amplifier. The adja- cent LED will illuminate when the Lead/Lead channel is selected. When the LED is dark, the Rhythm/Rhythm channel is selected. The CLEAN SELECTOR (32) must be in the BYPASS mode to activate either the Rhythm or Lead channel.

3CLEAN SELECTOR

This switch selects the Clean channel and will activate regardless of the position of the Lead/Rhythm SELECTOR (31). The adjacent LED will illuminate when the Clean chan- nel is selected. This switch must be in the BYPASS position, indicated by a dark LED, in order to utilize the Lead/Rhythm SELECTOR (31).

4EFFECTS SELECTOR

This switch activates the amplifier’s effects loop. The adjacent LED will illuminate when the effects loop is active.

Specifications

POWER AMPLIFIER SECTION:

Tubes:

Four EL34's with 12AX7 driver

Rated Power and Load:

120 W RMS into 16, 8, or 4 ohms

Power @ Clipping:

(Typically @ 5% THD, 1 kHz, 120 VAC line) 120 W RMS into 16, 8, or 4 ohms

Frequency Response:

±3 dB 50 Hz to 20 kHz @ 90 W RMS into 8 ohms

Hum and Noise:

Greater than 76 dB below rated power

Power Consumption:

Domestic: 400 W, 50/60 Hz, 120 VAC

Export: 400 W, 60 Hz, 220-230/240 VAC

PREAMP SECTION:

Tubes:

Three 12AX7

The following specs are measured @ 1 kHz with the controls preset as follows:

Low and High EQ @ 10, Mid EQ @ 0

Rhythm and Lead Posts @ 10

Bass, Middle and Treble EQ @ 5

Effects Send @ 0

Effects Return @ 10

Master Level @ 5

Nominal Levels are with Pre Gain @ 5

Minimum Levels are with Pre Gain @ 10

Clean Channel:

Nominal Input Level: -20 dBV, 100 mV RMS

Minimum Input Level: -30 dBV, 30 mV RMS

Maximum Input Level: 0 dBV, 1.0 mV RMS

Rhythm Channel:

Nominal Input Level: -80 dBV, 0.1 mV RMS

Minimum Input Level: -90 dBV, 0.03 mV RMS

Lead Channel:

Nominal Input Level: -80 dBV, 0.1 mV RMS

Minimum Input Level: -90 dBV, 0.03 mV RMS

Effects Send:

Load Impedance: 47 k ohms or greater

Minimum Output: -10 dBV, 300 mV RMS

Maximum Output: 0 dBV, 1 V RMS

Effects Return:

Impedance: High-Z, 80 k ohms

Minimum Input Sensitivity: -10 dBV, 300 mV RMS

Maximum Input Sensitivity: 0 dBV, 1 V RMS

Line Output:

Load Impedance: 47 k ohms or greater

Adjustable Output: ±20 dBV, 0.1 V RMS-10 V RMS

REMOTE FOOTSWITCH:

Special 3-button unit with LED indicators (supplied)

System Hum and Noise @ Nominal Level:

(Clean channel, 20 Hz to 20 kHz unweighted) Greater than 74 dB below rated power (Special noise gate circuitry for Lead & Rhythm)

Equalization: (Clean channel only)

Custom Low, Mid, and High passive type EQ

Voicing: (Rhythm and Lead channels only) Active Bass, Middle, and Treble EQ

Boost/Cut ±12 dB

Dimensions and Weight:

11.0" (279 mm) H x 26.5" (673 mm) W x 11.0" (279 mm) D 52 lbs. (23.6 kg)

14

15

Image 8
Contents 3120 Avertissement Risque de choc électrique NE PAS Ouvrir ºPSMFTT 4536$5*0/4*.1035/5&4%&4&$63*5& ºPEFSXFOJHFSFeatures Livello di pressione sonora in dBA, risposta lentoFront Panel Rear Panel Footswitch SpecificationsPower Amplifier Section Remote FootswitchBlock Diagram Peavey Electronics Corporation Limited WarrantyProduct Category Cables Limited LifetimeCaracterísticas Y Funciones Indicadores DE LED DE Activación DE LOS Canales Panel delanteroLámpara DEL Estado DEL Suministro Eléctrico LINE/OUT Panel traseroLINE/LEVEL Remote Switch conector del cable del pedal PedalToma IEC DE Alimentación DE Electricidad Cable DE Electricidad CA Para EL Mercado EstadounidenseDiagrama de bloques EspecificacionesSección DEL Amplificador DE Potencia Sección DEL PreamplificadorCategoría del producto Garantía Limitada DE Peavey Electronics CorporationCaractéristiques Panneau avant Panneau arrière Sélecteur Clean Cordon D’ALIMENTATION SECTEUR, ÉTATS-UNISRemarque ROYAUME-UNI Uniquement Prise DE ConnexionFootswitch Caractéristiques techniquesSchéma des circuits Section DE PuissanceGarantie Limitee Peavey Electronics Corporation AusstattungCatégorie de produit Câbles Durée de vie limitéePOWER-SCHALTER VorderseiteSTANDBY-SCHALTER NetzstatusleuchteBias TEST-Anschlüsse NachschwingschalterImpedanzschalter FÜR Lautsprecherboxen LautsprecherausgängeRückseite FußschalterTechnische Daten BlockschaltbildEndstufenbereich VorstufenbereichProduktkategorie Garantiebestimmungen DER Peavey Electronics CorporationCaratteristiche Pannello anteriore Pannello posteriore Pedale Diagramma a blocchi SpecificheSezione Amplificatore DI Potenza Sezione PreamplificatoreGaranzia Limitata DI Peavey Italia S.R.L Categoria del prodottoCavi Ciclo utile limitato Esclusioni dei risarcimenti