DigiTech RP21D manual Bank Names, Volume Pedal Update, Bank Showcase, Factory Reset?

Page 64

RP21D User’s Guide Section Four - Utilities

Bank Names

You can assign custom names to every Bank in the RP21D. The Procedure for naming your Banks is as follows:

1. Press the Utility button once. Use the Next or Previous Page buttons until you reach page 12 of the utilities. The Display reads:

2

Bank: Showcase

￿￿ Name?

1

2

￿ 1

 

3

1

4 Yes

LINK CHANGED

LINK CHANGED

 

LINK

CHANGED

LINK CHANGED

 

COMP WAH

TUBE

EQ GATE

L/R OUTS

FACTORY USER

 

 

DIST

EQ

#DIGITAL

 

 

 

 

 

 

PAGE 12OF15 b

 

 

 

 

 

 

 

 

 

CLIP

 

L/R OUTS

2.Press the number two button and rotate the Data Wheel to select the Bank that you wish to rename.

3.Press the number four button and rotate the Data Wheel. This will take you to the Name menu. Please see page 47 for Naming instructions.

Volume Pedal Update

The RP21D has the ability to update the position of the expression controller pedal when it is assigned to Volume within any program. This means that the volume pedals position will correspond to the volume setting after changing the ProgramTo enable this feature, the procedure is as follows:

1. Press the Utility button once. Use the Next or Previous Page buttons until you reach page 16. This display should look like this:

Vol Pedal Update￿￿

2

1

Off

2

dn￿ 1

 

3

1

4

LINK CHANGED

LINK CHANGED

 

LINK

CHANGED

LINK CHANGED

 

COMP

WAH

TUBE

EQ GATE

L/R OUTS

FACTORY USER

 

 

 

DIST

EQ

#DIGITAL

 

PAGE 13OF15 b

 

 

 

 

 

 

 

 

 

 

 

CLIP

 

L/R OUTS

2. To enable this Volume Pedal update rotate the Data Wheel until the display says On.

Now in any Program where the expression pedal is assigned to the Volume parameter, the expression pedal’s current position will be updated when that preset is selected.

Factory Reset

This function resets the RP21D to its original factory settings. This procedure will erase all custom user Programs, Defaults and Utility settings.

ATTENTION: This procedure will erase all user settings in the RP21D. Be sure you want to erase the memory and start fresh before continuing with this procedure.

To perform a Factory Reset, do the following:

1. Press the Utility button once. Use the Next or Previous Page buttons until you reach page13 of the utility menu. The Display reads:

2

Factory Reset?

￿￿

1 Yes

2

￿ 1

 

3

1

4

LINK CHANGED

LINK CHANGED

 

LINK

CHANGED

LINK CHANGED

COMP WAH

TUBE

EQ GATE

L/R OUTS

FACTORY USER

 

 

DIST

EQ

#DIGITAL

 

PAGE 14OF15 b

 

 

 

 

 

 

 

 

 

CLIP

 

L/R OUTS

2. To initiate the Reset, press the number one button. The Display reads:

59

Page 63 Page 65
Image 64
Page 63 Page 65
Contents
Page Mains Plug Warning RP21, RP21D Digitech ElectronicsDigitech III Table of Contents RP21D Features IntroductionApply Power Quick StartMaking Connections Select ProgramGuided Tour of the RP21D Front PanelRear Panel Getting Started Making ConnectionsStereo Powering the RP21D Program ModeAbout the RP21D DisplayFootswitches ProgramsExpression Pedal EffectsDigital Effects Modules Preamp/Analog ModulesEdge of the Earth Preamp Defaults Selecting a ProgramCreating Programs Editing the PreampCompressor CompressorHeavy ThreshRatio AttackMediumLevel CompressorWah Wah Tube DistortionWah Pedal Toe Heavy Tube DistortSaving a Distortion Default Type Dirty Tube GainSolid State Distortion DistortLow Fuzz Type FuzzLevel Phase Band Graphic EqualizerTube GEQ Punch80Hz 140Hz 250Hz 450Hz Noise GateTube GEQ Custom Noise Gate LoThresh TypeSilencer2Post T&D ThreshAtten AttackRelseNoise Gate Custom Master Preamp SettingsDISTPan Mix TubeOn Lvl DSPLvl Mstr DistByp Lvl DSPLvl MstrStoring a User Preamp Default Naming a DefaultPreAmp Custom NameUserDefault List RP21D User’s Guide Section Two Editing Functions Configuration Digital EffectsChanging Effects FXThru ModuleCenter FX Dual ChoFXLvl DryLvl Balance Speed Depth WvFrmDlyA DlyB Balance OutA PanA OutB PanBChoruses and Flangers Effect TypesChorus Chorus Parameters Flanger Flanger ParametersPhasers Phaser ParametersPedal Phaser Pedal Phaser ParametersRotary Speaker Simulator Tremolo and Auto-PannerFeedback Rotary Speaker Simulator ParametersDelays TremoloAuto Panner Tremolo & Auto Panner ParametersFX Lvl Dry Lvl Balance Dly Time FdBck TapIt Smear Delay ParametersFrequency Gain Dly a B Dly C D Out Multi Effects Modules Chorus/Delay and Flange/Delay Multi-Effect Module ParametersTime Warp Reverse DelaySampler Reverbs Reverb Gated ReverbReverb Parameters TypeDispersion DiffusionOver Type Over FreqDelay C Delay DDetuners Increasing, Shelf, and Reverse ShelfPitch Shifters and Harmony Dtn a BDtn C D Dtn E -HPitch Shifters Parameters Auto Wah Whammy EffectsWhammy Effect Parameters Auto Wah Effect Parameters EqualizersGraphic Equalizers Here are a couple of simple examplesParametric Equalizers Parametric Equalizer ParametersMaster Mix Cabinet EmulatorMaster Mix Dry Wet CabEmType Pre DigitalNameStyx And Stones Storing/Copying ProgramsStore Prg toStyx And Sto Select Contrl F.Switch Foot Controller FunctionsAssigning Programs Assigning On/Off FunctionsRe-assign F.switch ? Expression Pedal AssignmentsAssigning the Wah Assigning the Morph or VolumeSeries Modifiers Dynamic FiltersLow Frequency Oscillators Midi Continuous ControllersViewing, Changing, or Deleting Assignments FXLvl CC # Min MaxTuner Output Mode Cabinet EmulationMidi Channels OutputMono Program Receive Map Program Transmit Map Midi RcvChnl TransChnl Prg Rcv MapMIDI= UserSysEx Dump SysEx Channel and Midi MergeSysEx Channel Midi Merge User Default Dump Program DumpsSysExDump Bulk System SysExDump UserPrg³PrgNumAssigning a Midi CC to Pedals Assigning a Midi CC to the Expression PedalUsrDfltPreamp User PdlsBanks FS=Prg CCTranVolume Pedal Update Factory ResetFactory Reset? Bank NamesRecalibrating the Expression Pedal Are you sure ?Recalibrate Pedal ? Push pdl forward,pressSection Five Appendix RP21D Factory Program ListSpecifications Input SectionRemarks Recognized
Top Page Image Contents