RP21D User’s Guide Section Four - Utilities
| 2 | UsrDflt:Preamp | User 1 | |||||||||||||
|
|
| %kHz |
|
| %kHz |
| %kHz |
|
|
|
|
|
|
| |
| 1 |
| 2 | 3 | 4 | |||||||||||
| YesmsdB | msdB |
| U 1 | ||||||||||||
| LINK CHANGED |
| LINK CHANGED | LINK CHANGED |
| LINK CHANGED | ||||||||||
|
|
| COMP WAH | TUBE EQ | GATE |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| L/R OUTS | ||||||
FACTORY USER |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| # |
|
|
|
|
|
|
|
|
| |||
BANK | 9 OF 15 b |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
PAGE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
2.Press the number two button and rotate the Data Wheel to select the Effect Module whose Default you want to dump.
3.Press the number four button and rotate the Data Wheel to select the User Default you want to dump.
4.To initiate the dump, press the number one button and rotate the Data Wheel. The Display briefly reads “ Sending User Default.” It will then return to the User Default Dump Page.
Assigning a MIDI CC to Pedals
This function allows you to send MIDI Continuous Controller (CC) information out the MIDI port while the footswitch still maintains its ability to control a parameter within the RP21D. When assigned to a footswitch, the switch will toggle between CC values 0 or 127. CC numbers 0 through 127 are available. This function is only available for footswitches that have been programmed to toggle effects on and off within the RP21D. To assign the MIDI CC number which will be transmitted from the applicable footswitches, do the following:
1. Press the Utility button once, then use the Next or Previous Page buttons until you reach page 10 of the utility menu. The Display reads:
|
|
|
|
|
|
| |
2 | Pdls:Banks FS=Prg CCTran | ||||||
1 | 2 | 1 |
| 3 | 1 | 4 | |
LINK CHANGED | LINK CHANGED |
| LINK | CHANGED | LINK CHANGED | ||
| COMP WAH | TUBE | EQ GATE | L/R OUTS | |||
FACTORY USER |
|
| DIST | EQ | #DIGITAL |
| |
|
|
|
|
| |||
PAGE 10OF15 b |
|
|
|
|
| ||
|
|
|
| CLIP |
| L/R OUTS | |
2.Press the number two button and turn the Data Wheel to select the Bank which will be used to transmit the CC commands.
3.Press the number three button and turn the Data Wheel to select the footswitch that you wish to assign a CC number to.
4.Press the number four button and turn the Data Wheel to select the CC number you wish to transmit from the footswitch.
Assigning a MIDI CC to the Expression Pedal
The Expression Pedal can act as a MIDI continuous controller for external MIDI devices which you have connected to the MIDI out port of the RP21D. You can select any MIDI CC number between 0 and 127 that you want to transmit CC information on. The procedure for assigning a MIDI CC number to the Expression Pedal is as follows:
1. Press the Utility button once. Use the Next or Previous Page buttons until you reach page 11 of the utility menu. The Display reads:
Expression Send: CC#
2 | 1 | 2 | 1 |
| 3 | 1 | 4 OFF |
LINK CHANGED | LINK CHANGED |
| LINK | CHANGED | LINK CHANGED | ||
| COMP WAH | TUBE | EQ GATE | L/R OUTS | |||
FACTORY USER |
|
| DIST | EQ | #DIGITAL |
| |
PAGE 11OF15 b |
|
|
|
|
| ||
|
|
|
| CLIP |
| L/R OUTS | |
2. Press the number four button and turn the Data Wheel to select the CC number that you wish to transmit from the Expression Pedal.
58