DigiTech RP21D manual Specifications, Input Section

Page 67

RP21D User’s Guide

Section Five - Appendix

 

Specifications

Input Section

 

Connector:

1/4” Unbalanced

Nominal Value:

-8 dBu

Maximum Level:

+10 dBu

Impedance:

470 ohms

Output Section

 

Connector:

(2) 1/4” TRS Impedance Balanced

Nominal Level:

+4 dBu

Maximum Level:

+18 dBu

Impedance:

50 ohms

Digital Section

 

A/D Converter:

20 bit 128x Oversampled

D/A Converter:

20 bit 128x Oversampled

Sampling Rate:

44.1kHz.

Output:

S/PDIF

DSP Section

Architecture:

Static-Dynamic Instruction Set Computer (S-DISC II™)

Digital Signal Path Width:

24 bits (144.5 dB)

Internal Data Path:

48 bits (289 dB)

Dynamic Delay Memory:

256k x 24 bits (5.94 seconds)

Static Delay Memory:

256 24-bit registers (6.55 milliseconds)

Data ALU Processing:

10.0 MIPS

Address ALU Processing:

15.0 MIPS

Multiplier Size:

24 bits x 24 bits

General

Frequency Response:

20 Hz to 20 kHz +0, -3 dB

S/N Ratio:

Greater than 90 dB: ref= max signal, 22 kHz measurement bandwidth

THD:

Less than 0.04% (1 kHz)

Tube:

12AX7

Tube Plate Voltage:

145 Volts

Factory Programs:

128

User Programs:

128

Dimensions:

24” W x 8.25” D x 2.25” H

Net Weight:

12 lbs.

Shipping Weight:

13.5 lbs.

62

Page 66 Page 68
Image 67
Page 66 Page 68
Contents
Page Mains Plug Warning RP21, RP21D Digitech ElectronicsDigitech III Table of Contents Introduction RP21D FeaturesSelect Program Apply PowerQuick Start Making ConnectionsFront Panel Guided Tour of the RP21DRear Panel Making Connections Getting StartedStereo Display Powering the RP21DProgram Mode About the RP21DEffects FootswitchesPrograms Expression PedalDigital Effects Modules Preamp/Analog ModulesEdge of the Earth Editing the Preamp Preamp DefaultsSelecting a Program Creating ProgramsThreshRatio AttackMedium CompressorCompressor HeavyCompressor LevelTube Distort Wah WahTube Distortion Wah Pedal Toe HeavyType Dirty Tube Gain Saving a Distortion DefaultType Fuzz Solid State DistortionDistort Low FuzzPunch Level PhaseBand Graphic Equalizer Tube GEQ80Hz 140Hz 250Hz 450Hz Noise GateTube GEQ Custom ThreshAtten AttackRelse Noise Gate LoThreshTypeSilencer2 Post T&DNoise Gate Custom Master Preamp SettingsDISTPan Mix DistByp Lvl DSPLvl Mstr TubeOn Lvl DSPLvl MstrNameUser Storing a User Preamp DefaultNaming a Default PreAmp CustomDefault List RP21D User’s Guide Section Two Editing Functions Digital Effects ConfigurationFX Dual Cho Changing EffectsFXThru Module CenterSpeed Depth WvFrm FXLvl DryLvl BalanceOutA PanA OutB PanB DlyA DlyB BalanceChoruses and Flangers Effect TypesChorus Chorus Parameters Flanger Parameters FlangerPedal Phaser Parameters PhasersPhaser Parameters Pedal PhaserRotary Speaker Simulator Parameters Rotary Speaker SimulatorTremolo and Auto-Panner FeedbackTremolo & Auto Panner Parameters DelaysTremolo Auto PannerFX Lvl Dry Lvl Balance Dly Time FdBck TapIt Smear Delay ParametersFrequency Gain Dly a B Dly C D Out Multi-Effect Module Parameters Multi Effects Modules Chorus/Delay and Flange/DelayTime Warp Reverse DelaySampler Reverbs Type ReverbGated Reverb Reverb ParametersOver Freq DispersionDiffusion Over TypeIncreasing, Shelf, and Reverse Shelf Delay CDelay D DetunersDtn E -H Pitch Shifters and HarmonyDtn a B Dtn C DPitch Shifters Parameters Auto Wah Whammy EffectsWhammy Effect Parameters Here are a couple of simple examples Auto Wah Effect ParametersEqualizers Graphic EqualizersParametric Equalizer Parameters Parametric EqualizersCabEmType Pre Digital Master MixCabinet Emulator Master Mix Dry WetNameStyx And Stones Storing/Copying ProgramsStore Prg toStyx And Sto Assigning On/Off Functions Select Contrl F.SwitchFoot Controller Functions Assigning ProgramsExpression Pedal Assignments Re-assign F.switch ?Assigning the Wah Assigning the Morph or VolumeSeries Midi Continuous Controllers ModifiersDynamic Filters Low Frequency OscillatorsFXLvl CC # Min Max Viewing, Changing, or Deleting AssignmentsTuner OutputMono Output ModeCabinet Emulation Midi ChannelsPrg Rcv MapMIDI= User Program Receive MapProgram Transmit Map Midi RcvChnl TransChnlSysEx Dump SysEx Channel and Midi MergeSysEx Channel Midi Merge SysExDump UserPrg³PrgNum User Default DumpProgram Dumps SysExDump Bulk System PdlsBanks FS=Prg CCTran Assigning a Midi CC to Pedals Assigning a Midi CC to the Expression Pedal UsrDfltPreamp UserBank Names Volume Pedal UpdateFactory Reset Factory Reset?Push pdl forward,press Recalibrating the Expression PedalAre you sure ? Recalibrate Pedal ?RP21D Factory Program List Section Five AppendixInput Section SpecificationsRecognized Remarks
Top Page Image Contents