Akai Ewi4000s manual „ Adjusting the Reverb Effect Volume of Each Program

Page 24

„Adjusting the Reverb Effect Volume of Each Program

This procedure adjusts the volume of the Reverb effect for each Program individually, as opposed to the overall Reverb effect volume. The Reverb effect volume of each program is stored in the EWI4000s.

1.Select the program whose Reverb effect volume you want to adjust.

2.While holding the FX BUTTON, press the SETUP BUTTON. While pressing both these buttons, “rb” will be shown in the PROGRAM / DATA DISPLAY.

3.Release both buttons. The current Reverb effect volume of the selected program will be displayed.

4.Adjust the Reverb effect volume by pressing the HOLD BUTTON (which increases the volume value) or OCTAVE BUTTON (which decreases the volume value).

5.Press the SETUP BUTTON. The EWI4000s will return to Play Mode.

„Adjusting the Delay Effect Volume of Each Program

This procedure adjusts the Delay effect volume for each Program. The Delay effect volume setting of each program is stored in the EWI4000s.

1.Select the program you wish to adjust the Delay effect volume.

2.While holding the FX BUTTON, press the SETUP BUTTON. While pressing both these buttons, “rb” will be shown in the PROGRAM / DATA DISPLAY.

3.While pressing the SETUP BUTTON, release the FX BUTTON, then press the HOLD BUTTON so the PROGRAM / DATA DISPLAY now shows “dL.”

4.Release the SETUP BUTTON and HOLD BUTTON. The current Delay volume of the selected Program will be displayed.

5.Adjust the Delay volume by pressing the HOLD BUTTON (which increases the volume value) or OCTAVE BUTTON (which decreases the volume value).

6.Press the SETUP BUTTON. The EWI4000s will return to Play Mode.

„Adjusting the Chorus Effect On/Off on Each Program

This procedure selects whether the Chorus effect is set on or off for each Program. The Chorus effect setting of each Program is stored in the EWI4000s.

1.While holding the FX BUTTON, press the SETUP BUTTON. While pressing both these buttons, “rb” will be shown in the PROGRAM / DATA DISPLAY.

2.While pressing the SETUP BUTTON, release the FX BUTTON, then press the HOLD BUTTON so the PROGRAM / DATA DISPLAY now shows “CH.”

3.Release the SETUP BUTTON and HOLD BUTTON. The current Chorus setting of the selected program will be displayed.

4.Set the Chorus to either “on” or “OF” by pressing the HOLD BUTTON or OCTAVE BUTTON.

5.Press the SETUP BUTTON. The EWI4000s will return to Play Mode.

22

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Reference Manual Page Important Safety Instructions Portable Cart WarningFCC Warning Table of Contents Features IntroductionParts & Functions TOP PanelSide / Rear Panel „ Program / Data Display Section „ Glide Plate Section„ Bend Plate Section „ Cable Clutch SectionPower „ Using Battery Power„ AC adapter Connections Basic Operation Basic Operation„ Note Keys „ Octave Shift Rollers „ Grounding Plates„ Mouthpiece „ Vibrato„ Tonguing „ Pitch Bend PlatesAdjusting the Sensitivity of the Sensors „ Hold Button and Octave Button„ Adjusting the Breath Sensor „ Adjusting the Pitch Bend Sensors„ Adjusting the Vibrato Sensor „ Adjusting the Glide Sensor„ Adjusting the Touch Sensors „ a Note About Adjusting Your SensorsFingering Modes Internal Sound Program KEY Functions„ Selecting the Internal Sounds Program Key „ Assigning a Program Number to a Note Key„ Setting Program Change Preferences „ Recalling the Program Number Assigned to a Note Key„ Program Up with the Hold Button „ Program Down with the Octave ButtonAdjusting the Volumes „ Adjusting the Main Volume„ Adjusting the Volume of Each Program „ Adjusting the Reverb Volume„ Adjusting the Reverb Effect Volume of Each Program „ Adjusting the Delay Effect Volume of Each Program„ Adjusting the Chorus Effect On/Off on Each Program Octave Button Functions „ Assigning Functions to the Octave ButtonHold Button Functions „ Assigning Functions to the Hold Button Pitch Bend Plate Functions Glide Plate Functions„ Assigning Functions to the Pitch Bend Plates „ Assigning Functions to the Glide PlateAdjusting the KEY Delay „ Setting the Glide Effect Time & RateTuning Transpose Function Trans ButtonEditing the Internal Sound with Your Computer About Midi Transmitted Information from the EWI4000s Midi OUT„ Midi Program Change „ Changing the Midi Channel „ Changing the Breath Sensor Output„ Setting the Midi Velocity Value „ Changing the Vibrato Sensor Output to Another Midi Event„ Setting the Hold Function Hold Button on Midi Transmit „ Setting the Glide Plate Function on Midi Transmit„ Sending a Midi Panic Message to Reset All Controllers „ Sending an All Notes Off MessageRestoring the Factory Presets Level master Level preset Reverb masterMiscellaneous Notes EVI Fingerings„ The Right Hand „ The Left HandSoftware Updating „ Basic EVI FingeringsTroubleshooting Fingering Charts Octave Shift RollersEWI Fingerings Saxophone Fingerings Flute Fingerings Oboe Fingerings EVI Fingerings Midi Implementation Chart Transmit/Export Recognize/Import RemarksMenu Structure OctaveGlide Parameter Range Defaults Update Control Protocol OFF Specifications Sound ModulePage
Top Page Image Contents