Akai Ewi4000s manual Specifications, Sound Module

Page 49

SPECIFICATIONS

EWI4000s

Type

Wind-instrument type controller with sound module

Fingerings

EWI, saxophone, flute, oboe, EVI, and EVI reversed

Sensors

Note Keys:

touch sensors

 

Mouthpiece:

air pressure level sensor

 

Lip:

pressure level sensor

 

Bend Up/Down Plates:

touch sensors

 

Glide Plate:

touch sensor

 

Octave Shift Rollers:

touch sensors

 

Program Key:

touch sensor

Keys

LEVEL, FX, SETUP, TRANSPOSE, OCT, HOLD

Sensor Adjustment

Breath Sense, Breath Adjustment, Bend Width, Bend Adjustment,

 

Glide Time, Glide Adjustment, Vibrato Adjustment

Terminals

1 line out (1/4”)

 

 

1 headphone out (dual mono/stereo mini jack)

 

(Recommended min. headphone impedance: 32)

 

1 MIDI in (5-pin DIN)

 

 

1 MIDI out (5-pin DIN)

 

 

1 DC in (for optional AC adaptor MP-9II)

Other

Removal cable clutch

 

Power Requirement

4 AA batteries (alkaline or rechargeable)

 

(Approx. 8 hrs. continuous use by batteries except with headphones)

 

9VDC/200mA AC-adaptor MP-9II (optional)

Dimensions

670.5mm (L) x 61mm (W) x 69mm (D)

Weight

874g (without batteries)

 

Accessories

Neck strap, 4 AA batteries, cleaning cloth, mouthpiece cover,

 

Operator's Manual

 

 

 

 

SOUND MODULE

 

 

Sound type

Analog modeling synthesizer

 

Voices

2 (only with Octave & Hold function)

Control Range

8 octaves

 

Sound Source

2 Oscillators, 2 Filters

 

 

Waveforms: Saw Tooth, Triangle, Pulse

 

Noise Generator, Formant filter

Effect

Reverb, Delay, Chorus

 

Sound Capacity

100 (50 preset sounds x 2)

 

Display

2 7-segment LEDs

 

Function

Transpose, Tune, Note Hold, Octave, Program Change, Key Delay

Other

Sound Editor software for

EWI4000s is available from our Web site

 

(http://www.akaipro.com)

 

All specifications are subject to change without notice.

8-22-768X-D

47

Image 49
Contents Reference Manual Page Portable Cart Warning Important Safety InstructionsFCC Warning Table of Contents Introduction FeaturesTOP Panel Parts & FunctionsSide / Rear Panel „ Glide Plate Section „ Program / Data Display Section„ Cable Clutch Section „ Bend Plate Section„ Using Battery Power Power„ AC adapter Connections Basic Operation Basic Operation„ Note Keys „ Octave Shift Rollers „ Grounding Plates„ Vibrato „ Mouthpiece„ Tonguing „ Pitch Bend Plates„ Hold Button and Octave Button Adjusting the Sensitivity of the Sensors„ Adjusting the Pitch Bend Sensors „ Adjusting the Breath Sensor„ Adjusting the Glide Sensor „ Adjusting the Vibrato Sensor„ a Note About Adjusting Your Sensors „ Adjusting the Touch SensorsFingering Modes Program KEY Functions Internal Sound„ Selecting the Internal Sounds Program Key „ Assigning a Program Number to a Note Key„ Recalling the Program Number Assigned to a Note Key „ Setting Program Change Preferences„ Program Down with the Octave Button „ Program Up with the Hold Button„ Adjusting the Main Volume Adjusting the Volumes„ Adjusting the Volume of Each Program „ Adjusting the Reverb Volume„ Adjusting the Delay Effect Volume of Each Program „ Adjusting the Reverb Effect Volume of Each Program„ Adjusting the Chorus Effect On/Off on Each Program „ Assigning Functions to the Octave Button Octave Button FunctionsHold Button Functions „ Assigning Functions to the Hold Button Glide Plate Functions Pitch Bend Plate Functions„ Assigning Functions to the Pitch Bend Plates „ Assigning Functions to the Glide Plate„ Setting the Glide Effect Time & Rate Adjusting the KEY DelayTranspose Function Trans Button TuningEditing the Internal Sound with Your Computer Transmitted Information from the EWI4000s Midi OUT About Midi„ Midi Program Change „ Changing the Breath Sensor Output „ Changing the Midi Channel„ Changing the Vibrato Sensor Output to Another Midi Event „ Setting the Midi Velocity Value„ Setting the Glide Plate Function on Midi Transmit „ Setting the Hold Function Hold Button on Midi Transmit„ Sending a Midi Panic Message to Reset All Controllers „ Sending an All Notes Off MessageLevel master Level preset Reverb master Restoring the Factory PresetsEVI Fingerings Miscellaneous Notes„ The Right Hand „ The Left Hand„ Basic EVI Fingerings Software UpdatingTroubleshooting Octave Shift Rollers Fingering ChartsEWI Fingerings Saxophone Fingerings Flute Fingerings Oboe Fingerings EVI Fingerings Transmit/Export Recognize/Import Remarks Midi Implementation ChartOctave Menu StructureGlide Parameter Range Defaults Update Control Protocol OFF Sound Module SpecificationsPage