SV Sound SX-VT user manual Channel Power switch SX-ST series only, 13 PFL/AFL push button

Page 16

4.12 Channel Power switch (SX-ST series only)

It powers ON or OFF the entire input module. This function is useful to save the battery power when only a few numbers of channels are being used. An audible pop will be introduced in the mixer's outputs if this switch is used during normal operation.

4.13 PFL/AFL push button

The P/A push button is used to monitor the channel signal Pre-Fader PFL or After-Fader AFL and to check its level on the main level meters. A mode selector located on the Master/Monitoring Module let you choose between the 3 operating modes of the P/A button: SOLO/AFL/PFL

NOTES:

-you can still monitor the PFL signal even if the channel is turned OFF ( Muted )

-Jumper S12 (L) and S13(R) determine whether the AFL is taken Pre or Post PAN pot

4.13.1 P/A LED

The P/A LED lights ON to indicate when the PFL/AFL push button is depressed. This LED is blinking to warn you when the SOLO Mode is selected.

4.14VCA's Group Selector(SX-VT Series with VCA input module only)

The SX-VT series can be equipped with VCA's Mic/LineInput module ( Voltage Controlled Amplifier ).

Thus, the channel fader do not control the audio modulation but, instead, a DC voltage that controls the VCA circuitry.

This technology offers the possibility to build up an optional VCA grouping system of up to 8 independent groups.

A VCA Group allows to use just one fader to control the global mix level of a large group of channels ( such as drums, horns, backing vocals, etc.) and thus, providing an easier global control of that particular mix group.

The VCA Group Selector assigns the channel to one of the 8 VCA Groups. Each group is then controlled by a Master Group Fader located on a Master Fader Module by means of a DC voltage.

NOTE: when position "0" or "9" is selected, the channel is disconnected from the VCA grouping system

4.15Compressor (SX-VT series with VCA input module only)

This switch enables or disables the channel compressor. The compressor is used to limit the dynamic range of the modulation. In case of extreme amplitudes or signal peaks, heavy distortion may occur, especially with digital recording equipment. To avoid this kind of distortion or, for example, to avoid loudspeakers getting damaged by overload, use the compressor. Compressors can also be used to change the sound of an instrument by applying extreme settings. The principle function used in these devices is dependent on an automatic gain control which reduces the amplitude of loud passages and therefore restricts the original dynamics to a desired range.

4.15.1 Threshold

This control sets the threshold level for the compressor. It has a range of -30 to +infinity. Generally threshold levels for compressors are set below the normal operating level to allow upper dynamics to be musically compressed. For high ratio settings (limiter function), the threshold point is set above the normal operating level in order to provide reliable signal limiting and thus, protects subsequent equipments.

4.15.2 Ratio

It controls the compression ratio between the input and output levels for all signals exceeding the threshold point. The control range can be adjusted with the RATIO knob from a 1:1 ratio to an infinity:1 ratio.

4.15.3 Compressor LED

This Led will light ON only when the compressor becomes active and turns OFF when the compressor is inactive, depending if the signal level is equal to or higher than the threshold point.

SX-ST / SX-SV User Manual

page 16

Image 16
Contents Sonosax SX-ST / SX-VT Audio equipment manufacturerTable of Contents LED Specifications Key Features IntroductionGeneral Description VCA and Compressor optionsInstallation Safety InstructionsRemoving the battery compartment Battery Power Mode SX-ST Series onlyOpening the battery compartment Closing the battery compartment External DC Power Mode SX-ST Series onlyBatteries charger option for SX-ST Series only Operating Instructions MIC / Line Input Module Input Select Switch Mic power switch∅ Phase reversal switch Gain ControlsLF Cut and Equalizer AUX 1 to 4 PRE/OFF/POST switches Mix busses 1 to 8 assignmentAUX Sends 1 to Dual Peak Level MetersOn Push button Channel FaderChannel Power switch SX-ST series only 13 PFL/AFL push buttonOn Air signaling SX-VT serie only Mute functionStereo Line Input Module Mono selector Left & Right Gain ControlStereo Equalizer Balance Left Right Mix busses 1/2 to 7/8 assignmentsRemote 11 PFL/AFL push button11.1 P/A LED VCAs Group Selector optional on SX-VT Series onlyChannels A/D Converter Master & Monitoring Module 1 ST / M / Low Batt switch Meters Backlight switchLeds switches MetersPFL/AFL/SOLO and operating mode Power ON/OFFTalkback/SLATE and Oscillator Returns 1 toMonitoring Communication and Private LinesGroups and Aux Master Sections Summary of characteristics SpecificationsGeneral and notes Mic/Line inputs GainMain outputs Auxiliary outputsMonitor outputs Return InputsOperating temperature Power requirementsDimensions and weight