SV Sound SX-ST, SX-VT user manual Remote, 11 PFL/AFL push button, 11.1 P/A LED

Page 21

5.10 Remote

This switch enables the Fader Start function of the Stereo input. The Start / Stop function of any connected device with Fader Start option can be controlled by the Stereo input, and the Remote Led indicates the status :

-the Stop mode is activated when the Fader is closed and/or the channel is OFF, then the Led is blinking

-the Play mode is active when the Fader is open, even slightly, and the channel is ON, then the Led lights On

You can Start and Stop any connected device by either moving the Fader up and down or by switching the channel ON and OFF.

The Remote logic circuitries actuate two relays for the Start ( K3 ) and Stop ( K1 ) function. Thus the logic circuitries are totally isolated from external devices for optimal protection.

In normal mode, a Start and a Stop pulse of 125ms is sent to the corresponding relay everytime the start/stop satus is changed.

The operational mode can be changed from Pulse to State by switching internal Dip switch S9-A to On ( or 1). If State mode is choosen, then only the Stop relay is activated as follow:

-In Stop mode, the relay is open

-In Play mode, the relay is closed

5.11PFL/AFL push button

The P/A push button is used to monitor the channel signal Pre-Fader PFL or After-Fader AFL and to check its level on the main level meters. A mode selector located on the Master/Monitoring Module let you choose between the 3 operating modes of the P/A button: SOLO/AFL/PFL

NOTES:

-you can still monitor the PFL signal even if the channel is turned OFF ( Muted )

-the AFL being taken post VCA, the signal is then obviously post Balance

5.11.1 P/A LED

The P/A LED lights ON to indicate when the PFL/AFL push button is depressed. This LED is blinking to warn you when the SOLO Mode is selected.

5.12VCA's Group Selector( optional on SX-VT Series only)

The VCA group selector works the same way as on the Mic/Line input with VCA.

Please refer to this section for detailled informations

SX-ST / SX-SV User Manual

page 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Audio equipment manufacturer Sonosax SX-ST / SX-VTTable of Contents LED Specifications Introduction Key FeaturesVCA and Compressor options General DescriptionSafety Instructions InstallationBattery Power Mode SX-ST Series only Removing the battery compartmentOpening the battery compartment External DC Power Mode SX-ST Series only Closing the battery compartmentBatteries charger option for SX-ST Series only Operating Instructions MIC / Line Input Module Mic power switch Input Select Switch∅ Phase reversal switch Gain ControlsLF Cut and Equalizer Mix busses 1 to 8 assignment AUX 1 to 4 PRE/OFF/POST switchesAUX Sends 1 to Dual Peak Level MetersChannel Fader On Push button13 PFL/AFL push button Channel Power switch SX-ST series onlyMute function On Air signaling SX-VT serie onlyStereo Line Input Module Left & Right Gain Control Mono selectorStereo Equalizer Mix busses 1/2 to 7/8 assignments Balance Left Right11 PFL/AFL push button Remote11.1 P/A LED VCAs Group Selector optional on SX-VT Series onlyChannels A/D Converter Master & Monitoring Module Meters Backlight switch 1 ST / M / Low Batt switchLeds switches MetersPower ON/OFF PFL/AFL/SOLO and operating modeTalkback/SLATE and Oscillator Returns 1 toCommunication and Private Lines MonitoringGroups and Aux Master Sections Specifications Summary of characteristicsGeneral and notes Gain Mic/Line inputsAuxiliary outputs Main outputsMonitor outputs Return InputsPower requirements Operating temperatureDimensions and weight
Top Page Image Contents