Fujitsu MB15F74UV manual Absolute Maximum Ratings, Recommended Operating Conditions

Page 5

MB15F74UV

ABSOLUTE MAXIMUM RATINGS

Parameter

Symbol

 

Rating

Unit

 

 

 

Min

 

Max

 

 

 

 

 

 

 

 

 

 

 

Power supply voltage

VCC

0.5

 

4.0

V

 

 

 

 

 

 

Input voltage

VI

0.5

 

VCC + 0.5

V

 

 

 

 

 

 

 

Output voltage

LD/fout

VO

GND

 

VCC

V

 

 

 

 

 

 

DoIF, DoRF

VDO

GND

 

VCC

V

 

 

 

 

 

 

 

 

 

Storage temperature

Tstg

55

 

+125

°C

 

 

 

 

 

 

 

WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.

RECOMMENDED OPERATING CONDITIONS

Parameter

Symbol

 

Value

 

Unit

Remarks

 

 

 

Min

Typ

Max

 

 

 

 

 

 

 

 

 

 

 

Power supply voltage

VCC

2.7

3.0

3.6

V

VCCRF = VCCIF

 

 

 

 

 

 

 

Input voltage

VI

GND

VCC

V

 

 

 

 

 

 

 

 

Operating temperature

Ta

40

+85

°C

 

 

 

 

 

 

 

 

Note : VCCRF and VCCIF must supply equal voltage.

Even if either RF-PLL or IF-PLL is not used, power must be supplied to VCCRF and VCCIF to keep them equal.

It is recommended that the non-use PLL is controlled by power saving function.

Although this device contains an anti-static element to prevent electrostatic breakdown and the circuitry has been improved in electrostatic protection, observe the following precautions when handling the device.

When storing and transporting the device, put it in a conductive case.

Before handling the device, confirm the (jigs and) tools to be used have been uncharged (grounded) as well as yourself. Use a conductive sheet on working bench.

Before fitting the device into or removing it from the socket, turn the power supply off.

When handling (such as transporting) the device mounted board, protect the leads with a conductive sheet.

WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device’s electrical characteristics are warranted when the device is operated within these ranges.

Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure.

No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand.

5

Image 5
Contents Description FeaturesPackage Pin plastic BCC LCC-18P-M05PIN Assignments MB15F74UVPin no Descriptions PIN DescriptionMB15F74UV Block DiagramParameter Symbol Value Unit Remarks Min Typ Parameter Symbol Rating Unit MinAbsolute Maximum Ratings Recommended Operating ConditionsMin Typ Electrical CharacteristicsParameter Symbol Condition Charge pump Vs V do Parameter Symbol Condition Value Unit Min TypV ≤ V do ≤ V CC − 0.5 Current rate Vs Ta −40 C ≤ Ta ≤ 85 CProgrammable Functional DescriptionProgrammable Reference Counter R10 R11 R12 R13 R14Divide ratio R14 R13 R12 R11 R10 Data settingDivide ratio N11 N10 Divide ratioDivide ratio SW = Phase comparator input FC IF, RF = Do IF, Do RFCurrent value LD/fout pin stateStatus PS pin Power Saving Mode Intermittent Mode Control Circuit100 Parameter Min Typ Max UnitFC bit = Phase Comparator Output WaveformLD Output Logic IF-PLL section RF-PLL section LD outputOscilloscope Controller Divide ratio settingCatalog guaranteed range Typical CharacteristicsFin input sensitivity RF-PLL input sensitivity vs. Input frequencyInput sensitivity vs. Input frequency Oscin input sensitivitySensitivity InputCharge pump output voltage VDO MA mode Charge pump output current IDO mAFinRF input impedance Fin input impedanceFinIF input impedance Oscin input impedance Oscin input impedancePLL Reference Leakage PLL Phase NoiseReference Information Mkr x 439.99764 ∝s 50.0009 MHz Controller Application ExamplePart number Package Remarks Usage PrecautionsOrdering Information Fujitsu Limited C18058S-c-1-1 Dimensions in mm inches Package DimensionF0401 Fujitsu Limited