Thermos 461230404 manual Troubleshooting Electronic Ignition

Page 24

Troubleshooting - Electronic Ignition

Problem

Possible Cause

Check Procedure

Prevention/Solution

 

 

 

 

No sparks appear at

• Battery not installed

• Check battery orientation.

• Install battery (make sure that “+” and “–”

any electrodes when

properly.

 

connectors are oriented correctly, with “+” end up

ignition button is

 

 

and “–” end down.)

pushed; no noise can

 

 

 

be heard from spark

• Dead battery.

• Has battery been used

• Replace battery with new AA-size alkaline battery.

module.

 

previously?

 

 

• Button assembly not

• Check to insure threads are

• Unscrew button cap assembly and reinstall, making

 

installed properly.

properly engaged. Button

sure threads are aligned and engaged fully.

 

 

should travel up and down

 

 

 

without binding.

 

 

• Faulty spark module.

• If no sparks are generated

• Replace spark module assembly.

 

 

with new battery and good

 

 

 

wire connections, module is

 

 

 

faulty.

 

 

 

 

 

No sparks appear at

• Output lead

• Are output connections on

• Remove and reconnect all output connections at

any electrodes when

connections not

and tight?

module and electrodes.

ignition switch is

complete.

 

 

pushed; noise can be

 

 

 

heard from spark

 

 

 

module.

 

 

 

 

 

 

 

Sparks are present

• Output lead

• Are output connections on

• Remove and reconnect all output connections at

but not at all

connections not

and tight?

module and electrodes.

electrodes and/or not

complete.

 

 

at full strength

 

 

 

 

• Arcing to grill away

• If possible, observe grill in

• If sparks are observed other than from burner(s),

 

from burner(s).

dark location. Operate

wire insulation may be damaged. Replace wires.

 

 

ignition system and look for

 

 

 

arcing between output wires

 

 

 

and grill frame.

 

 

• Weak battery.

• All sparks present but weak

• Replace battery with a new AA-size alkaline battery.

 

 

or at slow rate.

 

 

• Electrodes are wet.

• Has moisture accumulated

• Use paper towel to remove moisture.

 

 

on electrode and/or in burner

 

 

 

ports?

 

 

• Electrodes cracked or

• Inspect electrodes for

• Replace cracked or broken electrodes.

 

broken “sparks at

cracks.

 

 

crack”.

 

 

 

 

 

 

A Division of W.C. Bradley Co. • Columbus, GA 31902

Image 24
Contents 461230404 80001008 Installation Safety Precautions Safety SymbolsTable of Contents Description Grill Lid Assembly 80001001 Cart Assembly Grill Bottom Assembly 80001003Side Shelf Assembly 80000059 KeyParts Diagram Model No Assembly Model No Align holes Regulator hose Fully tighten screws inside grill bottom at this time #10-24x3/8 screws AAA, 5mm lock washers BBB Flametamer Pivot wire Smaller basket on left door, larger basket on right door Make sure drain hole is on left side Slide grease receptacle into rails beneath grease tray Very Important LP Tank Removal, Transport And Storage LP Liquefied Petroleum GasLP Tank Filling Connecting Regulator To The LP Tank For your safetyLP Tank Exchange LP Tank Leak TestLeak Testing Valves, Hose and Regulator Turn all grill control knobs to OFFSafety Tips For Safe Use Of Your Grill And To Avoid Serious InjuryIgnitor Lighting General Grill Cleaning Match-LightingIgnitor Lighting The Sideburner Match LightingCleaning The Burner Assembly Storing Your GrillImmediately turn off gas at LP tank Wait for grill to coolFood Safety How To Tell If Meat Is Grilled ThoroughlyIndirect Cooking Indirect Cooking InstructionsTroubleshooting Problem Possible Cause Prevention/SolutionTroubleshooting Electronic Ignition Problem Possible Cause Check Procedure Prevention/Solution