Foster 9606801 user manual Adjustment of the minimum, Electrical connection of the cooker hob

Page 15

INSTALLER INSTRUCTIONS

IMPORTANT: After adjusting for use with a gas that is different from the initial testing one, replace the label on appliance housing with the one that corresponds to the new gas type.

ENGLISH

12. Adjustment of the minimum

Instructions for urban and methane gas

1. Light the burner and bring it to the minimum position.

2. Remove the gas tap knob and turn the adjust- ment screw [Fig. 8] inside or on the side of the tap rod (depending on the model), until a regular minimum flame is obtained.

3. Re-assemble the knob and verify burner flame

Fig. 8: adjustment of the minimum

stability (when quickly rotating the hand from

 

maximum to minimum position the flame must

 

not shut off).

 

4. Repeat the operation on all gas taps.

Instructions for liquid gas (LPG)

Tighten the screw inside, or on the side of the tap (depending on the mode), rod clockwise completely.

13. Electrical connection of the cooker hob

IMPORTANT: Before completing the following operation, always make sure that the voltage and sizing of the power supply line correspond to the characteristics indicated on the place located under the housing of the appliance. This plate must never be removed.

33

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Abstract Table of Contents Position of the identification plate Usage warningsDo not Allow Children to Come Close or Play with IT Safety warningsFlush built-in cooker hobs flush-mount edge Know your applianceFirst installation For further information on cleaning seePositioning in the work top Cooker hob distances Pressing it by hand FigAccurately clean milling Fastening the cooker hob to the cabinetMilling surface Fig Once these operations have been Fixed hooks Standard edge 8 mm Flush-mount edge Q4 only for S4000 series Sliding hooksStandard edge 8 mm Fixed bracketsConnection to liquid gas Room ventilationAdapting to different types of gasses Discharging combustion products exhaustCooker hob nozzle replacement Different types of gassesCorrectly reposition the burner in its seat Instructions for liquid gas LPG Adjustment of the minimumElectrical connection of the cooker hob Instructions for urban and methane gasLighting the burners Cooker hob useStandard burner knob Practical recommendations for burner use Pot diameterDiameter paragraph Daily ordinary cleaning Cleaning and maintenanceCleaning the stainless steel Cleaning gas componentsEdge type Tipo di bordoFori da incasso Key4000 N7254V = 1159 mm = 348 mm N7253V = 830 mm = 480 mmN7251V = 560mm = 480 mm= 430 mm N7277V= 360 mm N7211V QuadraN7215V = 1162 mm = 351 mmN7238V N7223V = 309 mm = 454 mm= 840 mm = 480 mm = 770 mm= 480 mm N7610V = 770 mm N7615V = 560 mm = 270 mm = 480 mm N7055V-10= 840 mm N7053V-10 = 560 mm = 480 mmN7290V LisaN7095V = 770 mm = 480 mm N7295V FaustEleonora N7075V N7047VFT1 N7048V = 770 mm = 480 mmN7067V = 560 mm = 480 mm N7066V N7097V N7297V = 950 mm = 480 mmN7063V = 420 mm = 480 mm N7367V R145N7266V Elettra Pandora = 560 mm = 480 mm N7065VN7024V N7044V = 740 mm = 480 mm Alien N7021V = 740 mm = 480 mm N7023V N7042V = 560 mmN7017VA = 560 mm = 480 mm Angolare15 F2000 N7038VN7260V = 840 mm = 480 mm AlfaN7052V 500 mm N7051VG N7260V
Top Page Image Contents