Foster 9606801 user manual Standard burner knob

Page 17

USER INSTRUCTIONS

The upper cover (B) of the burners must be placed in opposite seat with the two intro- ductions notches in correspondence of the two cylinders below (C) and tighten clock- wise.

ENGLISH

The associated burner is indicated near each knob. The appliance is equipped with an electric ignition device. It is sufficient to press the knob and rotate it anti-clockwise to the maximum flame symbol, until it is lit. If it does not ignite within the first 15 sec- onds, bring the knob on [chiuso] (closed) and do not try to re-ignite for 60 seconds.

OFF

MAX

MIN

Fig. 11: standard burner knob

Once it is lit, keep the knob pressed for a few sec- onds in order for thermocouple to heat up. It is possible that the burner shuts off when the knob is released: this means that the thermocouple was not sufficiently heated. Wait a few seconds and re- peat the operation, keeping the knob pressed for a little longer. Once the burner is lit, it is possible to

CHIUSO

MAX 1

MAX 2

1 INSIDE BURNER

2 EXTERNAL CROWNS

MIN 1

CHIUSO 2

adjust the flame based on need.

After every use of the hob, always verify that the control knobs are in [chiuso] (closed) posi- tion.

If the burners were to shut off accidentally, after about 20 seconds a safety device intervenes and blocks gas output, even when the tap is open. In this case bring the knob to [chiuso] (closed) position and do not try to light the burner for at least 60 seconds.

MAX 1

 

MAX 1

MIN 2

 

CHIUSO 2

Fig. 12: burner knob dual (S4000)/dual gear

CHIUSO 1 INSIDE BURNER

2 EXTERNAL CROWNS

1MAX

2CHIUSO

1 MIN

1 MIN

2 MIN

2 CHIUSO

 

1 MAX

2 MAX

Fig. 13: burner knob

dual (GIOTTO/VULCANO)

35

Image 17
Contents Abstract Table of Contents Position of the identification plate Usage warningsDo not Allow Children to Come Close or Play with IT Safety warningsFlush built-in cooker hobs flush-mount edge Know your appliancePositioning in the work top First installationFor further information on cleaning see Cooker hob distances Pressing it by hand FigMilling surface Fig Once these operations have been Accurately clean millingFastening the cooker hob to the cabinet Fixed hooks Standard edge 8 mm Flush-mount edge Q4 only for S4000 series Sliding hooksStandard edge 8 mm Fixed bracketsConnection to liquid gas Room ventilationAdapting to different types of gasses Discharging combustion products exhaustCorrectly reposition the burner in its seat Cooker hob nozzle replacementDifferent types of gasses Electrical connection of the cooker hob Adjustment of the minimumInstructions for urban and methane gas Instructions for liquid gas LPGLighting the burners Cooker hob useStandard burner knob Diameter paragraph Practical recommendations for burner usePot diameter Cleaning the stainless steel Cleaning and maintenanceCleaning gas components Daily ordinary cleaningFori da incasso Tipo di bordoKey Edge type4000 N7251V N7253V = 830 mm = 480 mm= 560mm = 480 mm N7254V = 1159 mm = 348 mm= 360 mm = 430 mmN7277V N7215V Quadra= 1162 mm = 351 mm N7211VN7238V N7223V = 309 mm = 454 mm= 480 mm N7610V = 770 mm N7615V = 560 mm = 840 mm = 480 mm= 770 mm = 840 mm N7055V-10N7053V-10 = 560 mm = 480 mm = 270 mm = 480 mmN7290V LisaEleonora FaustN7075V N7047VFT1 N7048V = 770 mm = 480 mm N7095V = 770 mm = 480 mm N7295VN7067V = 560 mm = 480 mm N7066V N7097V N7297V = 950 mm = 480 mmN7266V N7063V = 420 mm = 480 mm N7367VR145 N7024V N7044V = 740 mm = 480 mm Elettra Pandora= 560 mm = 480 mm N7065V N7017VA AlienN7021V = 740 mm = 480 mm N7023V N7042V = 560 mm 15 F2000 AngolareN7038V = 560 mm = 480 mmN7052V 500 mm N7051VG AlfaN7260V N7260V = 840 mm = 480 mm