![](/images/new-backgrounds/1294556/2945569x1.webp)
Safety Instruction continued
LP-Gas Supply System
§If the information is not followed exactly, a fire resulting in death or serious injury could occur.
§A 20lb tank of approximately 12 inches in diameter by
§This safety feature prevents the tank from being overfilled, which can cause malfunction of the LP gas tank, regulator and/or grill. §The LP gas supply cylinder to be used must be constructed and marked in accordance with the specifications for LP
§The tank supply system must be arranged for vapor withdrawal. §The LP gas tank used must have a collar to protect the tank valve §Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that is provided wit the cylinder valve. Other types of cap or plugs may result in leakage of propane
§Never connect an unregulated LP gas tank to your gas grill.
§This outdoor cooking gas appliance is equipped with a high capacity hose/regulator assembly for connection to a standard 20lb. Liquid propane cylinder.
§Have your LP gas tank filled by a reputable propane gas dealer and visually inspected and
§Never fill the cylinder beyond 80 percent full .
§Always keep LP gas tanks in an upright position.
§Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
§Storage of an outdoor cooking gas appliance indoors is permissible only if the cylinder is disconnected and removed from the outdoor cooking gas appliance..
§When your gas grill is not in use the gas must be turned off at LP gas tank.
•The gas must be turned off at the supply cylinder when the outdoor cooking gas appliance is not in use.
•LP gas tank must be stored outdoors in a
PROPER PLACEMENT AND CLEARANCE OF GRILL
•Never use your gas grill in a garage, porch, shed, breezeway or any other enclosed area. Your gas grill is to be used outdoors only.
•Do Not install this unit into combustible enclosures.
•Minimum clearance from sides and back of unit to combustible construction, 24 inches (61cm) from sides and 24 inches (61cm) from back.
•DO NOT use this appliance under overhead combustible surfaces. This outdoors cooking gas appliance is not intend to be installed in or on recreational vehicles and/or boats.
•Do Not obstruct the flow of ventilation air around the gas grill housing. Only use the regulator and the hose assembly supplied with your gas grill. Replacement regulators and hose assemblies must be those specified in this manual.
•The regulator and hose assembly must be inspected before each use of the grill. If there is excessive abrasion or wear or if the hose is cut, it must be replaced prior to the grill being put into operation. The replacement hose assembly shall be that specified by the manufacturer.
•Pressure regulator and hose assembly supplied with the outdoor cooking gas appliance must be used. Never substitute other types of regulator. Contact customer service for manufacturer specified replacement parts.
•This outdoor cooking gas appliance is equipped with a pressure regulator comply with the standard for Pressure Regulating Valves for LP Gas ANSI/ UL 144.
•Do not use briquettes of any kind in the grill.
•The grill is designed for optimum performance without the use of briquettes. Do not place briquettes on the radiant as this will block off the area for the grill burners to vent. Adding briquettes can damage ignition components and knobs, and void the warranty.
•Keep the back and side cart free and clear from debris. Keep any electrical supply cord, or the rotisserie motor cord away from the heated areas of the grill.
•Never use the grill in extremely windy conditions. If located in a consistently windy area (oceanfront, mountaintop, etc.) a windbreak will be required. Always adhere to the specified clearance.
•Never use a dented or rusty propane tank.
•Keep any electrical supply cord and the fuel supply hose away from any heated surface
•While lighting, keep your face and hands as far away from the grill as possible.
•Burner adjustment should only be performed after the burner have cooled.
5