Fisher & Paykel CAD-36, CAD-48, CAD-30 manual Outdoor Appliance Head Preparation

Page 8

INSTALLATION

CART ASSEMBLY INSTRUCTIONS

STEP 2

Outdoor Appliance Head Preparation

1.First you will need to remove the angle brackets from the side of the unit and replace them with cart mount brackets

(Fig. 04). Unit is shipped prepared for island installation.

2.Install the Bracket Tab on both sides using 8 of the

10-24 x 1/2” screws. Install each bracket with 4 screws on each side of the grill head (Fig. 04, 05 and 06). For a CAD-48, use the appropriately labeled bracket for your grill head and cart side.

SCREWS

Fig. 04

SCREWS

Fig. 05

Fig. 06

Note:

For the CAD-48 there are two sets of brackets. If you have the BGB48-BQR, use the brackets labeled LEFT-48 BQR and RIGHT-48 BQR. If you have the BGB48-BQAR, use the brackets labeled 48 BQAR.

STEP 3

Head Placement onto Cart (2 Persons Required)

1.Remove drip tray/pan (Fig. 07) and other removable components (to lighten the load) such as grates, top burner caps and components, and griddle flue cover, radiant tray and grill burner for easier handling.

2.Two persons required to lift head (Double Side Burner/Sink shown). Placing head on cart, place rear of head over the rear of the cart first (Fig. 08). Then allow the rear side tabs to first locate in the slots on the top of the cart sides. The other tabs will locate in the

middle and front slots as the head is lowered into position on the

Fig. 07

cart (Fig. 09).

 

TABS

Fig. 08

Fig. 09

6

Image 8
Contents Professional Grill Cart Page For Your Safety Message to OUR CustomersTable of Contents Safety Practices and PrecautionsModel Identification & Dimensions CAD-30 CAD-36 CAD-48CAD-30/36/48 Shipping InspectionInstallation Contents IncludedGetting Started Locating the CartStep Head Placement onto Cart 2 Persons Required Outdoor Appliance Head PreparationFront End Screw Installation Gas Hookup LP Cover HangerOptional Attach Side Shelf Accessory on Either Side Optional Attach Sink Drain Kit Content Included Tools RequiredTank Bracket Snap-lock Clip Bushing Installation Finger tight first, then use a wrench Screws Pinch Point Installation Cable tie Using the Cart Removing DrawersRE-INSTALLING Drawers Freezer Pack OPTIONAL, KIT #70696A Proper HandlingCare and Maintenance Brand Name CleanersService Warranty Limited WarrantyHOW Long does this Limited Warranty LAST? This Warranty does not CoverNo Other Warranties HOW to GET ServiceCommercial USE LA Desserte DE Gril Professionnel Veuillez Conserver CE Manuel À Titre DE Référence Lintention DE NOS ClientsPour Votre Sécurité Avertissement Table DES MatièresMesures DE Sécurité ET DE Précaution CAD-30 Identification ET Dimensions DU ModèleInspection Apres Livraison Contenu Placement DE LA DessertePour Commencer Étape Préparation de la tête de lappareil dextérieur RemarqueInstallation des vis sur le devant Branchement du gaz Propane Crochet DE CouvercleTablette Latérale accessoire en option Installation Fixation du kit de drain dévier en option Contenu Outils NécessairesConsole de réservoir Clip de sécurité à clapet Bague Installation Serrer à la main pour commencer puis utiliser une clé Avertissement Point DE Pincement Remarque Attache de câble Dépose DES Tiroirs Utilisation DE LA DesserteConsigne DE Sécurité Remontage DES Tiroirs Milieu DE Congélation EN OPTION, KIT N 70696A Manutention appropriéeEntretien ET Maintenance Produits DE Nettoyage DE MarquePour Lobtention DU Service DE Garantie Garantie Garantie LimitéeFisher & Paykel Sengage À Quelle EST LA Durée DE Cette Garantie LIMITÉE?Aucune Autre Garantie Pour Obtenir DES RéparationsUtilisation Commerciale Remarque Remarque