Desa VMH10RNC Minimum Clearance to Combustible Materials, BUILT-IN Fireplace Installation

Page 11

INSTALLATION

Continued

Minimum Clearances For Side Combustible Material, Side Wall, and Ceiling

A.Clearances from the side of the fireplace cabi- net to any combustible material and wall should follow diagram in Figure 6.

Example: The face of a mantel, bookshelf, etc. is made of combustible material and pro- trudes 3 1/2" from the wall. This combustible material must be 4" from the side of the fire- place opening (see Figure 6).

B.Clearances from the top of the fireplace opening to the ceiling should not be less than 36 inches.

C.For mantel clearances, see Figure 10 on page 12.

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS

Top

Left and

Bottom

 

Right Sides

and Rear

36"

6"

0"

 

Example

 

 

 

*

*Minimum 16 inches from Side Wall

Figure 6 - Minimum Clearance for

Combustible to Wall

BUILT-IN FIREPLACE

INSTALLATION

Built-in installation of this fireplace involves in- stalling fireplace into a framed-in enclosure. This makes the front of fireplace flush with wall. An optional trim kit accessory is available (see Ac- cessories, page 40). Trim will extend past sides of fireplace approximately 1/2 inch. This will cover the rough edges of the wall opening. If installing a built-in mantel above the fireplace, you must follow the clearances shown in Figure 10, page

11.Follow the instructions below to install the fire- place in this manner.

 

Actual

Framing

Height

26"

26 7/8"

Front Width

26 3/4"

26 7/8"

Depth

9 1/2"

10 1/2"

Bottom

3/4"

3/4"

1.Frame in rough opening. Use dimensions shown in Figure 7 for the rough opening. If installing in a corner, use dimensions shown in Figure 8 for the rough opening. The height is 26 7/8" which is the same as the wall opening above.

2.If installing GA3450T blower accessory, do so at this time. Follow instructions included with blower accessory.

Note: If not installing blower accessory, you may wish to run electrical wiring to your fire- place for future blower installation (see Ac- cessories, page 40). Use only approved three- wire electrical wiring.

WARNING: If pre-wiring, do not connect wiring to any elec- trical source at this time.

Install fireplace electrical outlet and connect wiring to outlet be- fore connecting to electrical source. The fireplace electrical outlet is included with the GA3450T blower accessory.

Only use the fireplace electrical outlet supplied with the GA3450T blower accessory.

Note: A qualified installer should make all elec- trical connections.

101/2"

267/8"

3/4" Off

The Floor

267/8" Minimum

Figure 7 - Rough Opening for Installing

in Wall

365/8"

257/8"

267/8" 513/4"

Figure 8 - Rough Opening for Installing

in Corner

112462-01C

www.desatech.com

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents What to do if YOU Smell GAS Table of Contents Safety Information Local Codes Unpacking Product FeaturesOptional Remote Control Accessories Product IdentificationHood Tabs Louver Baffle Sheet Metal Screws Firebox Top AssemblyAssembling Fireplace Shoulder Screw ScreenConfined and Unconfined Space AIR for Combustion VentilationProviding Adequate Ventilation Ventilation Air From Inside Building Determining FRESH-AIR Flow for Fireplace LocationVentilation AIR Determining if You Have a Confined or Unconfined SpaceVentilation Air from Inside Building InstallationFireplace Clearances Installation ItemsCheck GAS Type Example BUILT-IN Fireplace InstallationMinimum Clearance to Combustible Materials Flanges Mantel Clearances for Built-In InstallationIf you have not assembled firebox, follow in- structions on Optional Mantel Installation Removing Upper Louver Installing Optional Blower Accessory GA3450TInstalling Blower Accessory Assembling Trim Trim shipped with mantelPower Cord Snap Bushing Wire HarnessScrew Wiring Routing Hole Baffle Extension Cord For Built-In InstallationDoor Connecting to GAS SupplyAttaching Wood Base to Solid Floor IncludedPropane/LP Test Pressures In Excess Of 1/2 Psig 3.5 kPa Connecting Fireplace to GAS SupplyInstallation Items Needed Checking GAS ConnectionsEquipment Gas Regulator or Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPaEquipment Shutoff Valve ClosedInstalling 9-Volt Battery in Hand-Held Remote Control Unit Optional Wireless HAND-HELD Remote Control AccessoriesInstalling Receiver Terminal W Terminal R R Control Valve Jumper Wire One terminal of 25 ft. wireFeed wires through rectangular slots Shoulder Screw Log Screen Installing LOG SET and ScreenOperating Fireplace Ignitor Thermocouple Lighting InstructionsElectronic Ignitor Button Control Knob Thermocouple Ignitor Electrode Pilot BurnerThermostat Control Operation Manual Lighting ProcedureREMOTE-READY Models For Your Safety Read Before Lighting To Turn OFF GAS To AppliancePilot Burner Ignitor Electrode Control Knob Electronic IgnitorPilot Ignitor Burner Electrode ON/OFF Series Model Ghrcb Optional HAND-HELD Remote OperationGWMT1 Wall Mounted Thermostat Optional GWMS2 Wall Mounted Switch OptionalThermostat Series Model Ghrctb Pilot Burner Thermocouple Inspecting BurnersPilot Flame Pattern Burner Flame PatternCabinet Cleaning MaintenanceBurner Injector Holder and Pilot AIR Inlet Hole LOG SETTroubleshootiing Observed Problem Possible Cause RemedyTroubleshooting Hours of operation Bris. If found, clean burnerResidues from manufactur Tial operationGas leak. See Warning Service Hints SpecificationsWiring Diagram Replacement PartsIllustrated Parts Breakdown Install Battery According To This IllustrationTHERMOSTAT-CONTROLLED Models Parts List935 Parts Available not Shown Accessories Corner Mantel with Full Hearth Base WALL-MOUNT ON/OFF Switch GWMS2Receiver and HAND-HELD Thermostat Remote Control KIT Ghrctb Receiver and HAND-HELD Remote Control KIT Ghrcb112462-01C 112462-01C Limited Warranty VENT-FREE Compact Classic Hearth Fireplace Warranty InformationKeep this Warranty
Top Page Image Contents