Desa VMH10TNC, EFS10TNA, EFS10TPA Control Knob Electronic Ignitor, Pilot Ignitor Burner Electrode

Page 26

OPERATING FIREPLACE

Continued

D.Do not use this appliance if any part has been under water. Immediately call a quali- fied service technician to inspect the appli- ance and to replace any part of the control system and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

WARNING: You must oper- ate this fireplace with the fire- place screen in place. Make sure fireplace screen is installed be- fore running fireplace.

NOTICE: During initial operation of new fireplace, burning logs will give off a paper-burning smell. Open window to vent smell. This will only last a few hours.

WARNING: Burner will come on automatically within one minute when control valve is in the ON position after the pilot is lit.

1.STOP! Read the safety information above.

2.Make sure equipment shutoff valve is fully open.

3.Press in and turn control knob clockwise Clockwise to the OFF position (see Figure 40).

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information, column 2, page 25. If you don’t smell gas, go to the next step.

5.Press in and turn control knob counter-

clockwise C-clockwiseto the PILOT position.

Press in control knob for five (5) seconds (see Figure 40).

Note: You may be running this fireplace for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.

6.With control knob pressed in, press and re- lease electronic ignitor button. This will

light pilot. The pilot is attached to the front of the burner. If needed, keep pressing ig- nitor button until pilot lights.

Note: If pilot does not stay lit, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure, page 27.

7.Keep control knob pressed in for 30 sec- onds after lighting pilot. After 30 seconds, release control knob.

•If control knob does not pop out when re- leased, contact a qualified service person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 4 through 8.

8. Slightly push in and turn control knob coun-

terclockwise C-clockwiseto the ON position.

CAUTION: Do not try to ad- just heating levels by using the equipment shutoff valve.

Control Knob

Electronic

Ignitor

 

 

ON

O

T

 

L

 

I

 

P

 

F

 

FO

Figure 40 - Control Knob and Ignitor

Button Location (Shown as Supplied -

No Control Options)

Pilot

Ignitor

Burner

Electrode

Figure 41 - Propane/LP Gas Pilot

Pilot Burner

Ignitor

 

Electrode

Figure 42 - Natural Gas Pilot

26

www.desatech.com

112462-01B

Page 25 Page 27
Image 26
Page 25 Page 27
Contents What to do if YOU Smell GAS Table of Contents Safety Information Local Codes Product Identification Product FeaturesOptional Remote Control Accessories UnpackingShoulder Screw Screen AssemblyAssembling Fireplace Hood Tabs Louver Baffle Sheet Metal Screws Firebox TopConfined and Unconfined Space AIR for Combustion VentilationProviding Adequate Ventilation Determining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Fireplace LocationVentilation AIR Ventilation Air From Inside BuildingInstallation Ventilation Air from Inside BuildingFireplace Clearances Installation ItemsCheck GAS Type Example BUILT-IN Fireplace InstallationMinimum Clearance to Combustible Materials Flanges Mantel Clearances for Built-In InstallationIf you have not assembled firebox, follow in- structions on Optional Mantel Installation Assembling Trim Trim shipped with mantel Installing Optional Blower Accessory GA3450TInstalling Blower Accessory Removing Upper LouverPower Cord Snap Bushing Wire HarnessScrew Wiring Routing Hole Baffle For Built-In Installation Extension CordIncluded Connecting to GAS SupplyAttaching Wood Base to Solid Floor DoorPropane/LP Checking GAS Connections Connecting Fireplace to GAS SupplyInstallation Items Needed Test Pressures In Excess Of 1/2 Psig 3.5 kPaClosed Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPaEquipment Shutoff Valve Equipment Gas Regulator orInstalling 9-Volt Battery in Hand-Held Remote Control Unit Optional Wireless HAND-HELD Remote Control AccessoriesInstalling Receiver Terminal W Terminal R R Control Valve Jumper Wire One terminal of 25 ft. wireFeed wires through rectangular slots Shoulder Screw Log Screen Installing LOG SET and ScreenOperating Fireplace Thermocouple Ignitor Electrode Pilot Burner Lighting InstructionsElectronic Ignitor Button Control Knob Ignitor ThermocoupleTo Turn OFF GAS To Appliance Manual Lighting ProcedureREMOTE-READY Models For Your Safety Read Before Lighting Thermostat Control OperationPilot Burner Ignitor Electrode Control Knob Electronic IgnitorPilot Ignitor Burner Electrode Optional HAND-HELD Remote Operation ON/OFF Series Model GhrcbGWMT1 Wall Mounted Thermostat Optional GWMS2 Wall Mounted Switch OptionalThermostat Series Model Ghrctb Burner Flame Pattern Inspecting BurnersPilot Flame Pattern Pilot Burner ThermocoupleLOG SET Cleaning MaintenanceBurner Injector Holder and Pilot AIR Inlet Hole CabinetObserved Problem Possible Cause Remedy TroubleshootiingTroubleshooting Tial operation Bris. If found, clean burnerResidues from manufactur Hours of operationGas leak. See Warning Replacement Parts SpecificationsWiring Diagram Service HintsInstall Battery According To This Illustration Illustrated Parts BreakdownParts List THERMOSTAT-CONTROLLED Models935 REMOTE-READY Models Accessories Receiver and HAND-HELD Remote Control KIT Ghrcb WALL-MOUNT ON/OFF Switch GWMS2Receiver and HAND-HELD Thermostat Remote Control KIT Ghrctb Corner Mantel with Full Hearth Base112462-01B 112462-01B Limited Warranty VENT-FREE Compact Classic Hearth Fireplace Warranty InformationKeep this Warranty
Top Page Image Contents