Desa EFS10TNA Lighting Instructions, Electronic Ignitor Button Control Knob, Ignitor Thermocouple

Page 24

OPERATING FIREPLACE

Continued

D.Do not use this appliance if any part has been under water. Immediately call a quali- fied service technician to inspect the appli- ance and to replace any part of the control system and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

WARNING: You must oper- ate this fireplace with the screen in place. Make sure fireplace screen is installed before run- ning fireplace.

NOTICE: During initial operation of new fireplace, burning logs will give off a paper-burning smell. Open window to vent smell. Operate fireplace on HI position to burn off odor. This will only last a few hours.

1.STOP! Read the safety information above.

2.Make sure equipment shutoff valve is fully open.

3. Turn control knob clockwise Clockwise to the

OFF position.

4.

Wait five (5) minutes to clear out any gas.

 

Then smell for gas, including near the floor.

 

If you smell gas, STOP! Follow “B” in the

 

safety information above. If you don’t smell

 

gas, go to the next step.

5.

Turn control knob counterclockwise C-clockwise

 

to the PILOT position. Press in control knob

 

for five (5) seconds (see Figure 36).

 

Note: You may be running this fireplace

Note: If pilot does not stay lit, refer to Troubleshooting, page 31. Also, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure on page 25.

7.Keep control knob pressed in for 30 sec- onds after lighting pilot. After 30 seconds, release control knob.

Note: If pilot goes out, repeat steps 3 through 7. This fireplace has a safety inter- lock system. Wait one (1) minute for sys- tem to reset before lighting pilot again.

8.Turn control knob counterclockwise

C-clockwiseto desired heating level. The burner should light. Set control knob to any heat level between 5 (high) and 1 (low).

CAUTION: Do not try to ad- just heating levels by using the equipment shutoff valve.

Electronic

Ignitor Button

Control Knob

Figure 36 - Control Knob In The OFF

Position

Thermocouple

Ignitor Electrode

 

Pilot Burner

Figure 37 - Natural Gas Pilot

for the first time after hooking up to gas

supply. If so, the control knob may need to

Ignitor

Thermocouple

be pressed in for 30 seconds or more. This

will allow air to bleed from the gas system.

• If control knob does not pop out when

released, contact a qualified service per-

son or gas supplier for repairs.

6. With control knob pressed in, press and

release ignitor button (see Figure 36). This

will light pilot. The pilot is attached to the

front burner. If needed, keep pressing igni-

tor button until pilot lights.

ElectrodePilot Burner

Figure 38 - Propane/LP Gas Pilot

24

www.desatech.com

112462-01B

Page 23 Page 25
Image 24
Page 23 Page 25
Contents What to do if YOU Smell GAS Table of Contents Safety Information Local Codes Product Features Optional Remote Control AccessoriesProduct Identification UnpackingAssembly Assembling FireplaceShoulder Screw Screen Hood Tabs Louver Baffle Sheet Metal Screws Firebox TopAIR for Combustion Ventilation Providing Adequate VentilationConfined and Unconfined Space Determining FRESH-AIR Flow for Fireplace Location Ventilation AIRDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside BuildingInstallation Ventilation Air from Inside BuildingInstallation Items Check GAS TypeFireplace Clearances BUILT-IN Fireplace Installation Minimum Clearance to Combustible MaterialsExample Mantel Clearances for Built-In Installation If you have not assembled firebox, follow in- structions onFlanges Optional Mantel Installation Installing Optional Blower Accessory GA3450T Installing Blower AccessoryAssembling Trim Trim shipped with mantel Removing Upper LouverWire Harness Screw Wiring Routing Hole BafflePower Cord Snap Bushing For Built-In Installation Extension CordConnecting to GAS Supply Attaching Wood Base to Solid FloorIncluded DoorPropane/LP Connecting Fireplace to GAS Supply Installation Items NeededChecking GAS Connections Test Pressures In Excess Of 1/2 Psig 3.5 kPaTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Equipment Shutoff ValveClosed Equipment Gas Regulator orOptional Wireless HAND-HELD Remote Control Accessories Installing ReceiverInstalling 9-Volt Battery in Hand-Held Remote Control Unit Control Valve Jumper Wire One terminal of 25 ft. wire Feed wires through rectangular slotsTerminal W Terminal R R Installing LOG SET and Screen Operating FireplaceShoulder Screw Log Screen Lighting Instructions Electronic Ignitor Button Control KnobThermocouple Ignitor Electrode Pilot Burner Ignitor ThermocoupleManual Lighting Procedure REMOTE-READY Models For Your Safety Read Before LightingTo Turn OFF GAS To Appliance Thermostat Control OperationControl Knob Electronic Ignitor Pilot Ignitor Burner ElectrodePilot Burner Ignitor Electrode Optional HAND-HELD Remote Operation ON/OFF Series Model GhrcbGWMS2 Wall Mounted Switch Optional Thermostat Series Model GhrctbGWMT1 Wall Mounted Thermostat Optional Inspecting Burners Pilot Flame PatternBurner Flame Pattern Pilot Burner ThermocoupleCleaning Maintenance Burner Injector Holder and Pilot AIR Inlet HoleLOG SET CabinetObserved Problem Possible Cause Remedy TroubleshootiingTroubleshooting Bris. If found, clean burner Residues from manufacturTial operation Hours of operationGas leak. See Warning Specifications Wiring DiagramReplacement Parts Service HintsInstall Battery According To This Illustration Illustrated Parts BreakdownParts List THERMOSTAT-CONTROLLED Models935 REMOTE-READY Models Accessories WALL-MOUNT ON/OFF Switch GWMS2 Receiver and HAND-HELD Thermostat Remote Control KIT GhrctbReceiver and HAND-HELD Remote Control KIT Ghrcb Corner Mantel with Full Hearth Base112462-01B 112462-01B Warranty Information Keep this WarrantyLimited Warranty VENT-FREE Compact Classic Hearth Fireplace
Top Page Image Contents