Desa VMH10TNC, EFS10TNA, EFS10TPA, VMH10TPC Assembly, Assembling Fireplace, Shoulder Screw Screen

Page 6

ASSEMBLY

WARNING: Always have screen in place before operat- ing fireplace. This prevents ex- cessive temperatures on fire- place surfaces.

WARNING: Failure to posi- tion the parts in accordance with these diagrams or failure to use only parts specifically approved with this fireplace may result in property damage or personal injury.

ASSEMBLING FIREPLACE

Tools Required:

Phillips screwdriver

5/16" hex wrench

slotted screwdriver

scissors

1.Remove two screws that hold fireplace screen in place for shipping. These screws are located near top of screen. Discard screws. Lift fire- place screen up and pull out to remove (see Figure 2). Set screen aside until installation has been completed.

2.Cut two plastic straps to remove the log from the firebox cavity.

3.An optional blower is available. See Acces- sories, page 40. Install optional blower now. Follow installation instructions provided with blower. See Installing Optional Blower Ac- cessory GA3450T on page 14.

Shoulder

Screw

Screen

4.Locate four black phillips sheet metal screws from the hardware packet.

5.Rotate hood as shown in Figure 3. Make sure hood tabs point toward fireplace.

6.Insert hood tabs between baffle and louvers (see Figure 3).

7.Gently rotate hood to upright position. Make sure hood tabs are behind louvers and hood is resting on firebox top (see Figure 3).

8.Align screw holes on hood with screw holes on firebox top.

9.Insert screws as shown in Figure 3. Tighten screws firmly.

Hood Tabs

Hood

Louver

Hood Tab

Baffle

Sheet Metal

Screws

Firebox Top

Figure 3 - Assembling Hood

Figure 2 - Removing Screen

6

www.desatech.com

112462-01B

Image 6
Contents What to do if YOU Smell GAS Table of Contents Safety Information Local Codes Product Identification Product FeaturesOptional Remote Control Accessories UnpackingShoulder Screw Screen AssemblyAssembling Fireplace Hood Tabs Louver Baffle Sheet Metal Screws Firebox TopAIR for Combustion Ventilation Providing Adequate VentilationConfined and Unconfined Space Determining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Fireplace LocationVentilation AIR Ventilation Air From Inside BuildingInstallation Ventilation Air from Inside BuildingInstallation Items Check GAS TypeFireplace Clearances BUILT-IN Fireplace Installation Minimum Clearance to Combustible MaterialsExample Mantel Clearances for Built-In Installation If you have not assembled firebox, follow in- structions onFlanges Optional Mantel Installation Assembling Trim Trim shipped with mantel Installing Optional Blower Accessory GA3450TInstalling Blower Accessory Removing Upper LouverWire Harness Screw Wiring Routing Hole BafflePower Cord Snap Bushing For Built-In Installation Extension CordIncluded Connecting to GAS SupplyAttaching Wood Base to Solid Floor DoorPropane/LP Checking GAS Connections Connecting Fireplace to GAS SupplyInstallation Items Needed Test Pressures In Excess Of 1/2 Psig 3.5 kPaClosed Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPaEquipment Shutoff Valve Equipment Gas Regulator orOptional Wireless HAND-HELD Remote Control Accessories Installing ReceiverInstalling 9-Volt Battery in Hand-Held Remote Control Unit Control Valve Jumper Wire One terminal of 25 ft. wire Feed wires through rectangular slotsTerminal W Terminal R R Installing LOG SET and Screen Operating FireplaceShoulder Screw Log Screen Thermocouple Ignitor Electrode Pilot Burner Lighting InstructionsElectronic Ignitor Button Control Knob Ignitor ThermocoupleTo Turn OFF GAS To Appliance Manual Lighting ProcedureREMOTE-READY Models For Your Safety Read Before Lighting Thermostat Control OperationControl Knob Electronic Ignitor Pilot Ignitor Burner ElectrodePilot Burner Ignitor Electrode Optional HAND-HELD Remote Operation ON/OFF Series Model GhrcbGWMS2 Wall Mounted Switch Optional Thermostat Series Model GhrctbGWMT1 Wall Mounted Thermostat Optional Burner Flame Pattern Inspecting BurnersPilot Flame Pattern Pilot Burner ThermocoupleLOG SET Cleaning MaintenanceBurner Injector Holder and Pilot AIR Inlet Hole CabinetObserved Problem Possible Cause Remedy TroubleshootiingTroubleshooting Tial operation Bris. If found, clean burnerResidues from manufactur Hours of operationGas leak. See Warning Replacement Parts SpecificationsWiring Diagram Service HintsInstall Battery According To This Illustration Illustrated Parts BreakdownParts List THERMOSTAT-CONTROLLED Models935 REMOTE-READY Models Accessories Receiver and HAND-HELD Remote Control KIT Ghrcb WALL-MOUNT ON/OFF Switch GWMS2Receiver and HAND-HELD Thermostat Remote Control KIT Ghrctb Corner Mantel with Full Hearth Base112462-01B 112462-01B Warranty Information Keep this WarrantyLimited Warranty VENT-FREE Compact Classic Hearth Fireplace