Hearth and Home Technologies Crescent II Vertical Penetration Framing, Installing Attic Shield

Page 17

C.Vertical Penetration Framing

WARNING

Fire Hazard

Keep loose materials or blown insulation from touch- ing the vent pipe.

•National building codes recommend us- ing attic shield to keep loose materials/ blown insulation from contacting vent.

•Hearth & Home Technologies requires the use of an attic shield.

Installing the Firestop Spacer

•Frame an opening 10 inches by 10 inch- es whenever the vent system pene- trates a ceiling/floor (see Figure 6.3).

•Frame the area with the same sized lum- ber as used in ceiling/floor joist.

•When installing a top vent vertical appli- ance the hole should be directly above the appliance, unless the flue is offset.

•Do not pack insulation around the vent. Insulation must be kept away from the pipe.

Installing Attic Shield

Note: The firestop spacer is not required if attic shield is used.

•Frame opening for attic shield.

•Attic shield may be installed above or below ceiling (see Figure 6.4).

•Secure with three fasteners on each side.

•Fold tabs at top of attic shield in toward vent pipe. Tabs must keep vent pipe centered within shield.

•Field construct additional shield height if insulation is deeper than height of at- tic shield.

 

 

ATTIC

 

 

ABOVE

A

 

 

B

 

 

 

A

B

DVP

10 in.

10 in.

PIPE

 

 

Figure 6.3

 

 

 

BEND TABS IN

 

 

AROUND PIPE

 

 

3 FASTENERS

 

 

PER SIDE

 

ATTIC SHIELD INSTALLED

ATTIC SHIELD INSTALLED

BELOW CEILING

ABOVE CEILING

Figure 6.4

Installing the Attic Shield

 

Heat & Glo • Crescent II • 2083-902 Rev. G • 9/05

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents What to do if you smell gas Model CrescentHomeowner Reference Information CongratulationsTable of Contents BTU Specifications Glass SpecificationsHigh Altitude Installations 1Listing and Code ApprovalsGetting Started Design and Installation ConsiderationsInspect Appliance and Components Tools and Supplies NeededSelecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseSpace Mantel ProjectionsVent Termination Minimum Clearances Termination LocationsVent Termination Minimum Clearances Alcove ApplicationsVent Table Key Vent Information and DiagramsUse of Elbows Measuring StandardsTop Vent Horizontal Termination Vent DiagramsOne Elbow Two ElbowsMin Max Top Vent Horizontal Termination Three ElbowsV1 = 45 ft Max .7m Top Vent Vertical Termination No ElbowThree Elbows Top Vent Vertical TerminationPipe Clearances to Combustibles Wall Penetration Framing Vent Clearances and FramingCombustible Wall Penetration Non-Combustible Wall PenetrationVertical Penetration Framing Installing the Firestop SpacerInstalling Attic Shield Securing and Leveling the Appliance Appliance PreparationAssembly of Vent Sections Installing Vent PipeAttaching Vent to the Firebox Assembly Assembling Pipe SectionsAssembling DVP-12A Slip Sections Assembling Minimum Installations MI SectionsHorizontal Sections Disassembly of Vent SectionsSecuring the Vent Sections Vertical Sections Heat Shield Requirements for Horizontal Termination Installing Heat Shield and Horizontal Termination CapInstalling the Horizontal Termination Cap Pipe see Figure Installing Roof Flashing and Vertical Termination Cap16 Assembling the Storm Collar Around the Pipe Assembling and Installing Storm CollarFuel Conversions Gas Connection Gas InformationGas Pressures Pressure Natural Gas PropaneHigh Altitude Installations Connecting to the Appliance Recommendation for WireOptional Remote Control Requirements Electrical InformationAppliance will not operate unless properly grounded Heat Installing Flame Control Solenoid Natural Gas Only Junction Box InstallationFacing Requirements Mantel ProjectionsInside Fit Surround Clean the Appliance Appliance SetupAccessories Remove Shipping MaterialsPositioning the Logs Log Set Assembly LOGS-CrescentSRV2083-185Final placement appearance Removing Glass Assembly Glass AssemblyReplacing Glass Assembly Replacing Light BulbBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance Intellifire Ignition Lighting ApplianceFinal Inspection by After Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Intellifire Ignition System TroubleshootingSymptom Possible Causes Corrective Actions Before servicing Maintaining and Servicing ApplianceInspect Maintenance Tasks 16Reference Materials Appliance Dimension DiagramPipe Vent Components DiagramsDVP-TRAP Series DVP Components Not for use on this Model203 Service Parts ListLog Set Assembly with burner Crescent Limited Lifetime Warranty Heat & GLO GAS Appliance Products Limited Lifetime WarrantyContact Information

Crescent II specifications

Hearth and Home Technologies' Crescent II stands as a leading example of cutting-edge fireplace innovation, delivering both aesthetic appeal and efficient warmth to any home. Designed with a focus on user experience, the Crescent II combines modern design with state-of-the-art technology, making it an ideal choice for homeowners seeking both functionality and style in their heating solutions.

One of the standout features of the Crescent II is its sleek contemporary design. The large viewing area, framed by minimalistic lines, creates a striking focal point in any room, allowing homeowners to fully appreciate the mesmerizing dance of flames. Available in various sizes and finishes, the Crescent II can seamlessly integrate into diverse interior styles, from modern to traditional.

The Crescent II is equipped with advanced heating technologies, including a powerful airflow system that optimizes heat distribution throughout the space. This ensures that the warmth is evenly spread, eliminating cold spots that can diminish comfort levels. The unit operates with high efficiency, offering a thermal efficiency rating that meets and often exceeds industry standards, making it an environmentally friendly choice.

In addition to its heating capabilities, the Crescent II features a user-friendly interface, equipped with intuitive controls that make managing the fireplace a breeze. Homeowners can easily adjust the flame height and heat output, allowing for personalized comfort. Some models also come with optional smart technology, enabling remote control via smartphone apps for added convenience.

Another notable characteristic of the Crescent II is its commitment to safety. The unit includes safety features such as a secure glass front that remains cool to the touch, protecting users from burns. The fireplace is designed for venting options that reduce emissions and enhance indoor air quality, ensuring a safe and healthy home environment.

Maintenance is also simplified with the Crescent II. The design allows for easy access to components for cleaning and servicing, providing peace of mind that the fireplace will continue to perform optimally with minimal effort.

In summary, the Hearth and Home Technologies Crescent II is an exceptional fireplace that combines elegance, efficiency, and advanced technology. Its modern aesthetics, powerful heating capabilities, user-friendly controls, and commitment to safety make it a top choice for those looking to add a stylish and functional heating element to their home. With the Crescent II, homeowners can enjoy the warmth and ambiance of a fire while embracing convenience and modern living.
Top Page Image Contents