Hearth and Home Technologies Crescent II owner manual Troubleshooting, Intellifire Ignition System

Page 40

14 Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.

A. Intellifire Ignition System

Symptom

Possible Causes

Corrective Actions

1. The

a. Incorrect wiring.

Verify "S" wire (white) for sensor and "I" wire (orange) for ignitor are

ignitor/module

 

connected to correct terminals on module and pilot assembly. Reversed wires

makes noise, but no

 

at the module may cause system to make sparking noise, but spark may not

spark.

 

be present at pilot hood.

 

b. Loose

Verify no loose connections or electrical shorts in wiring from module to pilot

 

connections or

assembly. Rod closest to pilot hood should be ignitor. Verify connections

 

electrical shorts in

underneath pilot assembly are tight; also verify connections are not grounding

 

the wiring.

out to metal chassis, pilot burner, pilot enclosure, mesh screen if present, or

 

 

any other metal object.

 

c. Ignitor gap is too

Verify gap of igniter to pilot hood. The gap should be approximately .17 inch

 

large.

or 1/8 inch.

 

d. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor

 

 

wire "I" from module. Place ON/OFF Rocker switch or wall switch in ON

 

 

position. Hold ground wire about 3/16 inch away from "I" terminal on module.

 

 

If there is no spark at "I" terminal module must be replaced. If there is a spark

 

 

at "I" terminal, module is fine. Inspect pilot assembly for shorted sparker wire

 

 

or cracked insulator around electrode.

2. Pilot won't light,

a. Transformer

Verify that transformer is installed and plugged into module. Check voltage of

there is no noise or

installed correctly.

transformer under load at spade connection on module with ON/OFF switch

spark.

 

in ON position. Acceptable readings of a good transformer are between 3.2

 

 

and 2.8 volts AC.

 

b. A shorted or

Remove and reinstall the wiring harness that plugs into module. Verify there is

 

loose connection in

a tight fit. Verify pilot assembly wiring to module. Remove and verify continuity

 

wiring configuration

of each wire in wiring harness.

 

or wiring harness.

 

 

c. Improper wall

Verify that 110/VAC power is "ON" to junction box.

 

switch wiring.

 

 

d. Module not

Verify black ground wire from module wire harness is grounded to metal

 

grounded.

chassis of appliance.

 

e. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor

 

 

wire "I" from module. Place ON/OFF Rocker switch or wall switch in ON

 

 

position. Hold ground wire about 3/16 inch away from "I" terminal on module.

 

 

If there is no spark at "I" terminal module must be replaced. If there is a spark

 

 

at "I" terminal, module is fine. Inspect pilot assembly for shorted sparker wire

 

 

or cracked insulator around electrode.

3. Pilot lights but

a. A shorted or

Verify all connections to wiring diagram in manual. Verify connections

continues to spark,

loose connection in

underneath pilot assembly are tight. Verify connections are not grounding out

and main burner will

sensor rod.

to metal chassis, pilot burner, pilot enclosure or screen if present, or any other

not ignite. (If the

 

metal object.

pilot continues to

b. Poor flame

Verify that flame is engulfing sensor rod. If the pilot assembly does not have a

spark after the pilot

rectification or

ground strap, consider installing one to increase flame rectification. Verify

flame has been lit,

contaminated

correct pilot orifice is installed and inlet gas specifications. Flame carries

flame rectification

sensor rod.

rectification current, not the gas. If flame lifts from pilot hood, the circuit is

has not occurred.)

 

broken. A wrong orifice or too high an inlet pressure can cause pilot flame to

 

 

lift. The sensor rod may be contaminated. Clean sensor rod with emery cloth.

 

c. Module is not

Verify that module is securely grounded to metal chassis of appliance. Verify

 

grounded.

that wire harness is firmly connected to module.

40

Heat & Glo • Crescent II • 2083-902 Rev. G • 9/05

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Model Crescent What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents Glass Specifications BTU SpecificationsHigh Altitude Installations 1Listing and Code ApprovalsDesign and Installation Considerations Getting StartedInspect Appliance and Components Tools and Supplies NeededFraming and Clearances Selecting Appliance LocationConstructing the Appliance Chase ClearancesMantel Projections SpaceTermination Locations Vent Termination Minimum ClearancesAlcove Applications Vent Termination Minimum ClearancesVent Information and Diagrams Vent Table KeyUse of Elbows Measuring StandardsVent Diagrams Top Vent Horizontal TerminationOne Elbow Two ElbowsTop Vent Horizontal Termination Three Elbows Min MaxTop Vent Vertical Termination No Elbow V1 = 45 ft Max .7mTop Vent Vertical Termination Three ElbowsVent Clearances and Framing Pipe Clearances to Combustibles Wall Penetration FramingCombustible Wall Penetration Non-Combustible Wall PenetrationInstalling Attic Shield Installing the Firestop SpacerVertical Penetration Framing Appliance Preparation Securing and Leveling the ApplianceInstalling Vent Pipe Assembly of Vent SectionsAttaching Vent to the Firebox Assembly Assembling Pipe SectionsAssembling Minimum Installations MI Sections Assembling DVP-12A Slip SectionsSecuring the Vent Sections Vertical Sections Disassembly of Vent SectionsHorizontal Sections Installing the Horizontal Termination Cap Installing Heat Shield and Horizontal Termination CapHeat Shield Requirements for Horizontal Termination Installing Roof Flashing and Vertical Termination Cap Pipe see FigureAssembling and Installing Storm Collar 16 Assembling the Storm Collar Around the PipeGas Information Fuel Conversions Gas ConnectionGas Pressures Pressure Natural Gas PropaneHigh Altitude Installations Recommendation for Wire Connecting to the ApplianceOptional Remote Control Requirements Electrical InformationAppliance will not operate unless properly grounded Heat Junction Box Installation Installing Flame Control Solenoid Natural Gas OnlyMantel Projections Facing RequirementsInside Fit Surround Appliance Setup Clean the ApplianceAccessories Remove Shipping MaterialsLog Set Assembly LOGS-Crescent Positioning the LogsSRV2083-185Final placement appearance Glass Assembly Removing Glass AssemblyReplacing Glass Assembly Replacing Light BulbBefore Lighting Appliance Operating InstructionsBefore operating this appliance have a qualified technician Final Inspection by Lighting ApplianceIntellifire Ignition Initial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Troubleshooting Intellifire Ignition SystemSymptom Possible Causes Corrective Actions Maintaining and Servicing Appliance Before servicingInspect Maintenance Tasks Appliance Dimension Diagram 16Reference MaterialsVent Components Diagrams PipeDVP-TRAP Series Not for use on this Model DVP ComponentsLog Set Assembly with burner Service Parts List203 Crescent Limited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance ProductsContact Information

Crescent II specifications

Hearth and Home Technologies' Crescent II stands as a leading example of cutting-edge fireplace innovation, delivering both aesthetic appeal and efficient warmth to any home. Designed with a focus on user experience, the Crescent II combines modern design with state-of-the-art technology, making it an ideal choice for homeowners seeking both functionality and style in their heating solutions.

One of the standout features of the Crescent II is its sleek contemporary design. The large viewing area, framed by minimalistic lines, creates a striking focal point in any room, allowing homeowners to fully appreciate the mesmerizing dance of flames. Available in various sizes and finishes, the Crescent II can seamlessly integrate into diverse interior styles, from modern to traditional.

The Crescent II is equipped with advanced heating technologies, including a powerful airflow system that optimizes heat distribution throughout the space. This ensures that the warmth is evenly spread, eliminating cold spots that can diminish comfort levels. The unit operates with high efficiency, offering a thermal efficiency rating that meets and often exceeds industry standards, making it an environmentally friendly choice.

In addition to its heating capabilities, the Crescent II features a user-friendly interface, equipped with intuitive controls that make managing the fireplace a breeze. Homeowners can easily adjust the flame height and heat output, allowing for personalized comfort. Some models also come with optional smart technology, enabling remote control via smartphone apps for added convenience.

Another notable characteristic of the Crescent II is its commitment to safety. The unit includes safety features such as a secure glass front that remains cool to the touch, protecting users from burns. The fireplace is designed for venting options that reduce emissions and enhance indoor air quality, ensuring a safe and healthy home environment.

Maintenance is also simplified with the Crescent II. The design allows for easy access to components for cleaning and servicing, providing peace of mind that the fireplace will continue to perform optimally with minimal effort.

In summary, the Hearth and Home Technologies Crescent II is an exceptional fireplace that combines elegance, efficiency, and advanced technology. Its modern aesthetics, powerful heating capabilities, user-friendly controls, and commitment to safety make it a top choice for those looking to add a stylish and functional heating element to their home. With the Crescent II, homeowners can enjoy the warmth and ambiance of a fire while embracing convenience and modern living.
Top Page Image Contents