Char-Broil 4539937 General Grill Cleaningcon’t, Cleaning the Burner Assembly, Storing Your Grill

General Grill Cleaning(con’t.)

Plastic parts: Wash with warm soapy water and wipe dry. Do not use citrisol, abrasive cleaners, degreasers or a concentrated grill cleaner on plastic parts. Damage to and failure of parts can result.

Porcelain surfaces: Because of glass-like composition, most residue can be wiped away with baking soda/water solution or specially formulated cleaner. Use non-abrasive scouring powder of stubborn stains.

Painted surfaces: Wash with mild detergent or non-abrasive cleaner and warm soapy water. Wipe dry with a soft non- abrasive cloth.

Stainless steel surfaces: To maintain your grill’s high quality appearance, wash with mild detergent and warm soapy water and wipe dry with a soft cloth after each use. Baker-on grease deposits may require the use of an abrasive plastic cleaning pad. Use only in direction of brushed finish to avoid damage. Do not use abrasive pad on areas with graphics.

Cooking surfaces: If a bristle brush is used to clean any of the grill cooking surfaces, ensure no loose bristles remain on cooking surfaces prior to grilling. It is not recommended to clean cooking surfaces while grill is hot.

Cleaning the Burner Assembly

Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting grill.

1.Turn gas OFF at control knobs and LP cylinder.

2.Remove grease tray from back of grill.

3.Open doors, remove tank heat shield and grease pan from underneath the firebox.

4.Remove screws that hold orifice holder with the burner tube.

Figure A.

5.Remove cooking grates and radiator plates.

6.Remove hitch pin from front of the burner to disengage it.

Figure B.

7.Carefully lift up the burner enough to expose the electrode wire. Detach wire from electrode underneath the burner.

8.Carefully take out the burner to clean. Figure C.

9.While cleaning, make sure that the ignitor wire is not bent or broken.

A

Burner Tube

C

View from under firebox

B

Front

of

Grill

Pull hitch pin from front of burner

10

We suggest three ways to clean the burner tubes. Use the one easiest for you.

A.Bend a stiff wire (a light weight coat hanger works well) into a small hook. Run the hook through each burner tube several times.

B.Use a narrow bottle brush with a flexible handle (do not use a brass wire brush), run the brush through each burner tube several times.

C.Wear eye protection: Use an air hose to force air into the burner tube and out the burner ports. Check each port to make sure air comes out each hole.

10.Wire brush entire outer surface of burner to remove food residue and dirt.

11.Clean any blocked ports with a stiff wire such as an open paper clip.

12.Check burner for damage, due to normal wear and corrosion some holes may become enlarged. If any large cracks or holes are found replace burner.

VERY IMPORTANT: Burner tubes
must be properly connected to
orifice holders.	Correct
See illustration at right.	engagement

NOTE:

Reinstall

Orifice Screws

Holder

13.After cleaning put the burner back into the firebox and attach the electrode wire onto the electrode connector under the burner.

14.Place burner into position and reinstall the hitch pin.

15.Under the firebox, attach the orifice holder with the burner tube with the screws previously removed.

16.Replace the grease pan, tank heat shield, grease tray, radiator plate and cooking grates.

Storing Your Grill

-Clean cooking grates. -Store in a dry location.

-When LP cylinder is connected to grill, store outdoors in a well-ventilated space and out of reach of children.

-Cover grill if stored outdoors. Choose from a variety of grill covers offered by manufacturer.

-Store grill indoors ONLY if LP cylinder is turned off and disconnected, removed from grill and stored outdoors.

-When removing grill from storage, follow “Cleaning the Burner Assembly” instructions before starting grill.