Pride Mobility Jazzy 600 XL O M F O R T a D J U S T M E N T S, Comfort Adjustments, Lock

Page 22

V . C O M F O R T A D J U S T M E N T S

COMFORT ADJUSTMENTS

After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and controller position. If your power chair is equipped with a medium-back, a high-back, or a reclining seat, refer to the following information. If your power chair is equipped with a Specialty Seating System, refer to the information provided in separate manauls.

WARNING! If your power chair was configured by your authorized Pride Provider, please consult your healthcare professional before changing the seat position or making any other adjustment. Some adjustments may degrade your power chair’s performance and safety by changing its center of gravity.

WARNING! Some power chair components are heavy. You may need assistance to lift or carry them. Please refer to the specifications table for specific component weights before you disassemble the power chair.

WARNING! Prevent injury. Remove the occupant from the power chair before making any adjustments.

You may need the following to make comfort adjustments:

!metric/standard socket set and ratchet

!adjustable wrench

!thread lock

Seat Height and Seat Angle Adjustment

You can change the seat height to one of four positions in 1- in. increments by raising the front and rear trapeze bars. If you raise or lower only one trapeze bar (front or rear), you can also change the seat base angle (dump).

Figure 13. Seat Latch Safety

To change the seat height:

1.Turn off the power to the controller.

2.Loosen the rear shroud fasteners and remove the rear shroud. See figure 6.

3.Disconnect the controller connector(s) from the power base. See figure 7.

4.Flip up the seat latch safety. See figure 13.

5.Squeeze the seat latch and release the seat from the front trapeze bar.

6.Slide the seat forward and remove it from the power base.

7.Loosen the screws that attach the trapeze bars to the seat posts. See figure 14.

8.Remove the retaining clips that secure the seat posts to the power base. See figure 14.

9.Move the trapeze bars up or down to the desired height.

NOTE: Change the seat dump by raising or lowering only one set of towers (front or back).

10.Reinstall the retaining clips from step 8.

11.Remove each screw from the trapeze bars and apply thread

 

TRAPEZE BARS

 

SEAT POSTS

SEAT POSTS

RETAINING

CLIPS

 

RETAINING

 

CLIPS

 

lock.

Figure 14.Trapeze Bar Adjustment

22

www.pridemobility.com

Jazzy 600 XL

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S N T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Information ExchangePride Owners Club My authorized Pride ProviderProduct Safety Symbols S a F E T YS a F E T Y Pre-Ride Safety Check ModificationsTire Inflation Weight LimitationsIncline Information Cornering Information Braking InformationPublic Streets and Roadways Stationary Obstacles Steps, Curbs, etc Freewheel ModeOutdoor Driving Surfaces Stairs and EscalatorsElevators TransfersDoors Lift/Elevation ProductsPositioning Belts Inclement Weather PrecautionsMotor Vehicle Transport Reaching and BendingAlcohol Electromagnetic and Radio Frequency Interference EMI/RFII . Y O U R P O W E R C H a I R Jazzy 600 XLJazzy 600 XL Specifications Jazzy 600 XL Power Base Electrical ComponentsJazzy 600 XL Electrical Components Manual Freewheel Levers To engage or disengage the drive motorsInitial Assembly A S S E M B L YSeat Installation To install the seatO M F O R T a D J U S T M E N T S Comfort AdjustmentsSeat Height and Seat Angle Adjustment To change the seat heightSeat Position Seatback Angle AdjustmentReclining Seat Foot Platform Height Adjustment Armrest Width AdjustmentArmrest Angle Adjustment Foot Platform Depth AdjustmentTo clamp the quick release fastener Foot Platform Angle AdjustmentTo adjust the foot platform angle Controller PositionElevating Leg Rests Swing-away FootrestsHeavy Duty Drop-in Leg Rests To change foot plate position B Multi-Axis Foot PlatesTo change leg rest length a To change foot plate tilt CBatteries and Charging To charge the batteries using the onboard chargerB a T T E R I E S a N D C H a R G I N G Charging the BatteriesBattery Break-in Frequently Asked Questions FAQsHow can I get maximum range or distance per charge? Why do my new batteries seem weak?How can I ensure maximum battery life? What type of batteries should I use?What about public transportation? How should I store my power chair and its batteries?What about shipping? Joystick I . O P E R a T I O NFlight Controller KeypadOn/Off Key Battery Condition MeterLock Mode To lock the Flight controllerError Code Probable Cause Possible Solution Sleep Mode If EnabledError Codes Speed KeysTemperature Care and MaintenanceShould your power chair come in contact with water I I . C a R E a N D M a I N T E N a N C EMonthly Checks Daily ChecksWeekly Checks Yearly ChecksCleaning Instructions Tire/Wheel Replacement Jazzy 600 XL Drive WheelBattery Replacement To replace the batteriesBattery Installation When to See Your Authorized Pride Provider for Service Corrective MaintenanceW a R R a N T Y Service Checks and Warranty Service Reconditioned Units WarrantyWarranty Exclusions Exclusions also include components with damage caused byQuality Control Jazzy 600 XL Pride keeps a more detailed report on file at the factory
Top Page Image Contents