Invacare Standard and Heavy Duty Wheelchairs, Lightweight manual Replacing Heel Loop

Page 35

SECTION 4—FRONT RIGGINGS

 

 

Horizontal

 

 

Support

Calf Strap

Upper Portion of

 

 

Notch

Footrest

Impact Guard

 

 

 

 

 

Impact

 

Horizontal

Guard

 

 

 

Support

 

FIGURE 4.6 Installing Impact Guards/Calf Strap

Replacing Heel Loop

NOTE: For this procedure, refer to FIGURE 4.7 on page 36.

1.Pull the cam lock lever up to unlocked position.

2.Perform one of the following as shown in Detail ʺAʺ.

Footplates with Spring Buttons: Push in the release buttons and remove the footplate assembly from the front rigging support.

Bolt-In-Place Footplates:

i.Using a screw driver to hold the threaded rivet in position, remove the button head screw from the threaded rivet.

ii.Remove the threaded rivet and button head screw securing the footplate assembly to the front rigging support.

3.Remove the mounting screw, spacer and locknut that secure the heel loop to the footplate.

4.Remove existing heel loop from slide tube.

5.Install new heel loop onto slide tube.

6.Install the mounting screw, spacer and locknut to secure the heel loop to the footplate. Tighten until the spacer is secure.

7.Insert the lower footrest assembly into the upper footrest assembly to desired height.

8.Perform one of the following as shown in Detail ʺAʺ:

Footplates With Spring Buttons: Ensure that the release buttons fully protrude from holes on both sides of the upper footrest support.

Bolt-In-Place Footplates:

i.From the outside of the swingaway front rigging, insert the threaded rivet through both the front rigging support and the footplate assembly.

ii.From the inside of the swingaway front rigging, insert the button head screw through the appropriate adjustment hole and thread into the threaded rivet.

iii.Using a screwdriver to hold the threaded rivet in position, securely tighten the button head screw. Torque to 32 in-lbs.

Image 35
Contents Lightweight, Standard and Heavy Duty Wheelchairs Lightweight, Standard and Heavy Duty Wheelchairs Table of Contents Front Riggings Table of Contents Complete and mail the form on the next Register Your ProductCity State/Province Product Registration FormFold here Cut Along Line Wheelchair TIE-DOWN Restraints and Seat Restraints Special NotesSpecial Notes Important Notice Label LocationTypical Product Parameters LightweightTypical Product Parameters Anti-Tippers General GuidelinesStability All Models Operating Information Tire Pressure Weight Limitation Weight TrainingStability and Balance SAFETY/HANDLING of WheelchairsSafety/Handling of Wheelchairs Coping With Everyday Obstacles Do not tip the wheelchair without assistance Reaching, Leaning and Bending ForwardReaching and Leaning Backwards TippingMethod 2 Wheelchair Without Step Tubes Method 1 Wheelchair With Step TubesStairways Transferring To and From Other Seats EscalatorsUnfolding Unfolding and Folding WheelchairDo not allow upholstery to hang between the cross braces Folding WheelchairInspect/Adjust Initially Safety INSPECTION/TROUBLESHOOTINGSafety Inspection Checklist Inspect/Adjust Monthly Inspect/Adjust WeeklyInspect/Adjust Periodically TroubleshootingSuggested Maintenance Procedures MaintenanceMaintenance Safety Precautions Safety INSPECTION/TROUBLESHOOTING Removing Installing/Removing Front RiggingsInstalling Front RiggingsBolt-In-Place Height Adjusting Footplate HeightSpring Button Height Fixed Frame Fixed FrameInstalling Impact Guards/Calf Strap Raising/Lowering Elevating Legrest AssemblyReplacing Heel Loop Installing Impact Guards/Calf StrapFootrest shown Arms UsingReplacing Removing/Installing ArmrestsRemoving Armrest Installing ArmrestSeat and Back Installing Back Canes Lightweight Wheelchair OnlyReplacing Seat Upholstery Adjusting Seat WidthReplacing Back Upholstery Pivot Link Seat and Back Removing Upper Mounting Hardware Standard Wheelchair with Fixed FrameHeavy Duty Wheelchairs Removing Lower Mounting HardwarePivot Link Seat and Back Rear Wheels Removing/Installing Rear WheelsReplacing Rear Wheel Handrim Replacing/Repairing Rear Wheel TireFront Casters Installing/Replacing/Adjusting Front Casters and ForksInstalling/Replacing Front Casters and Forks Replacing Front Casters Adjusting ForksReplacing Front Casters Replacing/Repairing Front Caster Tire/TubeANTI-TIPPERS/WHEEL Locks Installing/Adjusting Anti-tippersInstalling Anti-Tippers Installing/Adjusting Anti-tippers- Anti-Tipper Length Adjusting the Anti-TippersUsing Patient Operated Disk Wheel Locks Using/Adjusting Disk Wheel LocksAdjusting Patient-Operated Wheel Locks Adjusting Patient-Operated Wheel LocksInstalling Wheel Lock Shoe Extensions Installing Wheel Lock Shoe ExtensionsChanging Seat-to-Floor Height Seat to FloorHeight Mounting Position Standard and Heavy Duty/Extra Wide Wheelchairs Installing the Seat Positioning StrapOptions Lightweight Wheelchairs Options Options Limited Warranty Made in Mexico