Invacare Electric wheelchair manual Error codes and diagnostic codes

Page 46

7.8.1Error codes and diagnostic codes

The drive electronics are capable of rectifying some errors automatically. In this case the status display will cease to flash. Please switch the remote on and off several times. Wait approx. 5 seconds each time before switching the remote on again. If this does not rectify the error, locate the error using the flash codes shown below.

	FLASH			FAULT			IMMEDIATE MEASURE			FURTHER HELP
	FLASH			FAULT			IMMEDIATE MEASURE			FURTHER HELP
	CODE
	1			Module defective.		-			•	Consult dealer.
	2			Lifter raised or		•	If lifter is raised, lower in		-
				lowered too far (seat			stages until the status
				not at driving height)			display stops flashing. If
							lowered too far, raise lifter
							in stages until the status
							display stops flashing. If at
							all possible, only drive
							when the seat is at driving
							height.
				Accessory error.		-			•	Consult dealer.
	3			Error on right motor.		•	Check plug-in connectors.		•	Consult dealer.
				Connection
				loose/faulty.
	4			Error on left motor.		•	Check plug-in connectors.		•	Consult dealer.
				Connection
				loose/faulty or motor
				faulty.

46

Image 46

Contents Invacare Typhoon How can you get in touch with Invacare? Deutschland DanmarkPortugal Table of Contents Pushing the wheelchair by hand Adjusting the wheelchair to the users seating postureREM 24 SD Remote Care and maintenance Repair Instructions Electrical SystemRepairing a flat tyre Introduction Dear userPage This symbol warns you of danger Important symbols in this manualRequirements Type Classification and Area of Use Permissable operating conditionsIndications Safety Notes General Safety NotesPage Page Safety Information on Electromagnetic Interference Safety Information on Driving and Freewheel Mode Page Safety Information on Wheelchairs with a Lifter Important if Your Wheelchair is Equipped with a LifterMore than 15-45 Safety Information on Wheelchairs with Recaro SeatsStandstill Driving Key features Remove the standard armrest in order to side transfer Getting in and out of the wheelchairRemoving the armrest Swivel up armrest Removing the skirtguard optional to get onGetting into the wheelchair Getting out of the wheelchairDriving Before driving for the first timeSureStep System Taking ObstaclesStability Lock System Components of the SureStep and the Stability Lock system Maximum obstacle heightSafety information when ascending obstacles Safety information when descending obstaclesAscending and descending Correct way to overcome obstaclesRight Wrong Driving up and down gradients Parking and stationaryDisengaging motors Pushing the wheelchair by handManually disengaging conventional motors Re-engaging motorsElectrically disengaging GB motors Manually disengaging GB motors emergency disengaging Layout of the remote REM 24 SD RemoteUpper side ControlsDisplays Underside Rear panelBattery charger display ON/OFF diode status displayDeactivating the immobilizer Activating / deactivating the immobilizerActivating the immobilizer Magnetic keyUsing the Buddy buttons with the remote What is a Buddy button?Will the wheelchair not drive after switching on? Controlling the wheelchair using the remoteCan the electronic system programming be adapted? Page Operating the electric adjustment options Activating adjustment modeSelecting and operating the adjustment option InformationChanging back to driving mode Error diagnosis Battery discharged. Please charge the batteryError codes and diagnostic codes Flash Fault Immediate Measure Further Help CodeFlash Fault Immediate Measure Further Help Code Recaro seats Adjusting the wheelchair to the users seating postureRecaro Seats Adjusting the armrests and the joystick box Adapting the remote to the length of the user’s armSetting the height of the remote Setting the height of the armrests Setting the width of the armrests Where to find the adjustment screwsDoing the adjustment Manually adjusting the seat tilt Page Adjusting the backrest using the gas pressure spring Manually adjusting the backrestAdjusting angle of the backrest Adjust the backrest using the perforated plate Flex and Contour Seats Lifter Please note Speed restrictionExplanation of symbols on lifter warning sticker Electric legrest LegrestsCompletely lowering electrical legrests as dismounting aid Adjustable legrest Adjusting the angle PrerequisitesAdjusting the length of the legrest Prerequisites Adjusting the calf plate to the calf width of the user Adjusting the angle of the foot plate Prerequisites Electrical System Electronics Protection SystemMain fuse Batteries What you need to know about batteriesPage Charging the batteries Charging the batteries After contact with skin Removing and fitting batteriesAfter contact with eyes Removing the batteries Page Page Page Page Releasing the lifter locking mechanism Disposing of dead or damaged batteries correctly Cleaning the vehicle Care and maintenanceDisinfection Legrests Maintenance Jobs Seat and backrest paddingSide part and armrest TyresCleaning Maintenance JobsElectronics / Electrical System Repairing a flat tyre Repair InstructionsRequirements Removing the wheel Repairing the flat tyre Explosion Hazard Disassembly Page Refurbishment Disposal Technical Specifications Charging deviceDimensions Standard Contour Recaro Flex Weight Without lifter With lifter Loading Inspections Performed English