Emerson IM-106-4050 instruction manual OxyBalance Specifications

Page 11

Instruction Manual

IM-106-4050 Original Issue March 2006

OxyBalance Oxygen Display and Averaging System

SPECIFICATIONS

Specifications for the OxyBalance system are listied in Table 1-2.

Table 1-2. OxyBalance Specifications

SPECIFICATIONS(1)

Ambient Environment

Temperature specification

Ambient temperature effect on electronics Vibration

Shock

Enclosure

Area Classification

Power Requirements

MicroLogix 1200

Resistive Load on Current Output Input Impedance for Current Terminal

PanelView Plus 600

Minimum On-State Current Nominal On-State Current Maximum On-State Current Current per Group Common 240V ac (Maximum Volts) 120V ac (Maximum Volts) 125V dc (Maximum Volts) 24V dc (Maximum Volts)

I/O

Signal Inputs

Signal Outputs

Signal Output Resolution (for averages) Signal Output Resistive Load Discrete Inputs

Relay Outputs

Architecture

Logic

Individual probes removed from average if

Signal Security

Personnel Security

Color Graphic Display

Size

Type

Resolution

23oF to 149o F (-5oC to 65oC)

Less than .01% of reading per 10oC

IEC 68-2-6 and ISA S37.3

IEC 68-2-31 and ISA S37.3

NEMA 4X

General Purpose

100-240 VAC, 50/60 Hz

0 to 500 Ohms (includes wire resistance)

275 Ohms

2.0mA at 10V dc

8.9mA at 24V dc

12. mA at 30V dc

8A

2.5A(2) (Amperes Continuous)

2.5A(2) (Amperes Continuous)

1.0A (Amperes Continuous)

2.0A (Amperes Continuous)

4-20 mA (qty. 1 to 8 O2 probes)

4-20 mA (qty, 1 to 8 pass through each probe, qty. 4 programmable averages)

12 bit

Less than 500 ohms

"IN CAL" (qty. 2 to 8 from individual probes)

"LOSS OF PLC"

"AVERAGE WARN" if one or more probes drop out of an average. "AVERAGE FAILED" for each average when only one probe in the average remains valid.

Each probe utilizes its own autonomous conditioning electronics, including its own power supply. Any failure in the OxyBalance system will not affect the individual 4-20 mA signals going to the control room for each probe.

4 programmable averages from 2-8 probes

1.) Probe fails (4-20 mA to default condition of 3.5 mA or 21 mA

2.) Probe is in cal (SPS / IMPS contact, must share with control room)

4-20 mA signals to be wired in series to the PLC and to the DCS I/O marshalling panel such that the loss of the PLC will not affect the transmission of the individual probe signals to the DCS. If PLC power, I/O cards or processor card(s) are lost, 4-20 mA signals from the probes are still transmitted to the control room.

Password protection configuration changes in programmable averages.

6" diagonal

Color Active Matrix, TFT LCD

320 by 240 min. Touch screen operator interface

(1)Specifications are subject to change without notification. Our policy is one of continuous improvement and we reserve the right to change specifications.

(2)1.5A above 40oC.

1-5

Image 11
Contents OxyBalance Page Table of Contents Section B Appendix aOxygen Display and Averaging System OxyBalanceEssential Instructions Preface Definitions Symbols Section Description Component Checklist Part NumbersSystem Overview General OxyBalance System FeaturesModules Physical DescriptionPanelView Plus MicroLogix 1200 Programmable Logic ControllerFailure / Warning Terminals Signal Pass Through TerminalsPower Terminals Output Average TerminalsOxyBalance Specifications SpecificationsOxyBalance Oxygen Display and Averaging System Overview System Considerations Section InstallationMounting Wiring Connections SetupInstallation Wiring Schematic Pass-Through Terminals Overview Section SetupLogin Required Screen LoginLogin Not Required Screen Scale Values GeneralTime and Date Time and Date SetupAverage1 Average4 Average SetupProbes CurrentAverages Fault ConditionAverage1- Average4 TrendAll Probe # 1-8 calibration in progress AlarmAverage # 1-4 warning Average # 1-4 failedOxyBalance Oxygen Display and Averaging System OxyBalance Oxygen Display and Averaging System Averaging System Section CalibrationOxybalance CalibrationOxyBalance Oxygen Display and Averaging System Overview Panelview Plus Maintenance and ServicePanelView Removal PanelView System WiringMounting Lever Removal Mounting Procedures PanelView InstallationMounting Levers Installation PLC Removal Micrologix 1200 Programmable ControllersRibbon Cable and Pull Loop Removal from DIN Rail PLC ReplacementModule Removal Module ReplacementOxyBalance Oxygen Display and Averaging System Overview Probe Failure TroubleshootingOxyBalance Oxygen Display and Averaging System Recommended Spare Parts Spare Parts ListingOxyBalance Oxygen Display and Averaging System Optional Accessories OxyBalance Oxygen Display and Averaging System Appendix a Safety Data Safety Instructionsimportant Belangrijk OxyBalance Oxygen Display Averaging System OxyBalance Oxygen Display and Averaging System Tärkeää OxyBalance Oxygen Display and Averaging System Wichtig Importante Viktig OxyBalance Oxygen Display and Averaging System OxyBalance Oxygen Display Averaging System Viktigt OxyBalance Oxygen Display and Averaging System Returning Material Appendix B Returning Equipment to the FactoryOxyBalance Oxygen Display and Averaging System Warranty Asia Pacific

IM-106-4050 specifications

The Emerson IM-106-4050 is a cutting-edge instrument designed for industrial measurement and control applications. Known for its reliability and advanced features, this device has gained popularity across various sectors, including oil and gas, chemical processing, and HVAC.

One of the standout features of the IM-106-4050 is its robust design, which makes it suitable for harsh industrial environments. Built with high-quality materials, this instrument can withstand extreme temperatures, humidity, and vibration, ensuring accurate performance in challenging conditions.

The IM-106-4050 integrates state-of-the-art technologies that enhance its functionality. One of its key technologies is the advanced sensor technology that provides precise measurement of process variables such as pressure, temperature, and flow. This accuracy is critical for maintaining optimal process control and ensuring safety in industrial operations.

Another significant characteristic of the IM-106-4050 is its versatility. It supports multiple input types, allowing it to work with various sensors and transmitters. This adaptability makes it an ideal choice for industries with diverse measurement requirements. The device also features a user-friendly interface that simplifies the configuration and operation, enabling technicians to access critical information quickly.

In addition to its measurement capabilities, the IM-106-4050 offers comprehensive communication options. It supports various communication protocols, including HART, MODBUS, and Profibus, facilitating seamless integration with existing control systems. This connectivity is vital for real-time monitoring and reporting, enhancing decision-making processes in industrial settings.

The IM-106-4050 is designed with data logging and advanced diagnostic capabilities. It can store historical data for analysis, enabling users to track trends and make informed adjustments to processes. Furthermore, its diagnostic features help identify potential issues before they escalate, reducing downtime and maintenance costs.

In conclusion, the Emerson IM-106-4050 stands out as a reliable and advanced instrument for measurement and control in industrial applications. With its rugged design, precise sensor technology, versatility, comprehensive communication options, and data logging capabilities, it serves as an invaluable asset for industries striving for efficiency and safety in their processes. As technology continues to evolve, the IM-106-4050 remains a key player in the landscape of industrial instrumentation, meeting the demanding needs of modern applications.