AMX RE-DM4, RE-DM6 manual Undefine Dimmer NEW

Page 55

AMX RADIA Lighting Programming

Set Default Level Time

This function sets the time taken for a level to change from its current level to a new level when using a level command.

Set Default Level Time

 

 

Command:

LT<time>

 

 

Response:

None

 

 

Examples:

SEND_COMMAND Radia,'LT3'

Set default level ramp time to 3 seconds.

 

 

 

 

SEND_COMMAND Radia,'LT0'

Set default level ramp time to 0 seconds (instantaneous).

 

 

 

Set Default Preset Time

This function sets the time taken for a preset recall to ramp when no time is specified to override this default time.

Set Default Preset Time

Command:

PT<time>

 

 

 

 

Response:

None

 

 

 

 

Example:

SEND_COMMAND Radia,'PT4'

Set default preset ramp time to 4 seconds.

 

 

 

Set Default Ramp Time

This function sets the default ramp rate for ramping strings, command, and channels (e.g. 'U', 'D', 'PU', 'PD'). The specified ramp rate is the time required to ramp from 0 to 100%.

Set Default Ramp Time

Command:

RT<time>

 

 

 

 

Response:

None

 

 

 

 

Example:

SEND_COMMAND Radia,'RT5'

Set ramp time to 5 seconds

 

 

 

A ramp time of zero (0) is invalid.

Ramp to Level

This function ramps the specified dimmer(s) to the specified level over the optionally specifiable time.

Ramp To Level

Command:

P<dimmer>L<level>T[<time>]

 

 

 

 

Response:

None

 

 

 

 

Examples:

SEND_COMMAND Radia,'P2L88'

Ramp dimmer 2 to 88% at the default level rate.

 

 

 

 

SEND_COMMAND Radia,'P1-4&6L100'

Ramp 1-4, and 6 to 100% at the default level rate.

 

 

 

 

SEND_COMMAND Radia,'P6L50T5'

Ramp dimmer 6 to 50% over 5 seconds.

 

 

 

 

SEND_COMMAND Radia,'PAL0'

Ramp all dimmers to 0% at the default ramp rate.

 

 

 

Undefine Dimmer (NEW)

This function "undefines" the specified dimmer so that it will not be included in the next saved preset. This allows a preset to affect a subset of the dimmers rather than all of them.

Undefine Dimmer

Command:

UN<dimmer>

 

 

 

 

Response:

None

 

 

 

 

Examples:

SEND_COMMAND Radia,'UN1'

Set dimmer 1 to undefined level.

 

 

 

 

SEND_COMMAND Radia,'UN2-4'

Set dimmers 2-4 to undefined level.

 

 

 

 

SEND_COMMAND Radia,'UNA'

Set all dimmers to undefined level.

 

 

 

RE-DM4 and RE-DM6 RADIA Eclipse Dimmer Modules

47

 

 

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Radia Eclipse Dimmer Modules AMX Limited Warranty and Disclaimer Page Page Table of Contents Radia Lighting System Configuration Pages Initial Level Status Reporting Appendix a AMX Lighting Curves Radia Eclipse RE-DM4 Dimmer Module OverviewSuggested Loads RE-DM4 SpecificationsRE-DM4 Specifications Dimmed SwitchedLine-In Connections RE-DM4 4-pin module connector maleLighting Application for the RE-DM4, Example a RE-DM4 Lighting Application DrawingsRE-DM6 6-channel Integrated Dimmer Module Radia Eclipse RE-DM6 Dimmer ModuleSuggested Installation Loads RE-DM6 SpecificationsRE-DM6 Specifications Line-In Connections for the RE-DM6 Lighting Application for the RE-DM6, Method a RE-DM6 Lighting Application DrawingsAMX Lighting Control Equipment FeaturesApplications AMX Lighting Control EquipmentIntegrated dimmer control modules Dimmer AccessoriesDimmer modules Power considerations Wiring ConsiderationsSpace Requirements Knockout locations RDA-ENC2 used as example ConduitRDA-ENC2, -ENC4, and -ENC6 enclosure and dimensions RDA Enclosure DimensionsRDA-ENC6B and RDA-ENC12B enclosures and dimensions Distance a to B Mounting AMX Lighting EnclosuresHigh-Voltage Connections Connecting High-Voltage, Single-Phase Input Power and LoadsRDA-ENC6B 120/240 VAC Line Input Single Phase RDA-ENC6B 120 VAC Single Phase Line InputConnecting High-Voltage Input Power and Loads RDA-ENC6B 120/208 VAC three-phase 4 W + G wiring diagram RDA-ENC6B 120/208 VAC line input three phaseRDC-PFC Power Distribution And Line Input References RDA-ENC6B Three Phase Line Input Connector ReferenceEnclosure module mounting slots and mounting screw holes Installing RDM Modules Into an RDA EnclosureLow-Voltage Connections Green LED Status IndicatorModule Connections Configuring and connecting multiple controllers Red LED Status Indicators RE-DM4 onlySW1 DIP Switch Setting Values for AxLink Configuring and Connecting AxLinkValue Failsafe Input External powerConnecting Dry Closures Dry ClosuresDefault Presets Default SettingsDefault Low-End Settings Default preset time valuesLighting System Link Radia Lighting System Configuration PagesMain Lighting System Radia Configuration ManagerDevice Configuration Device ConfigurationPresets section Preset Configuration Radia Lighting System Configuration Pages Software AMX Radia Lighting ProgrammingPreset Status Presets Defined vs. Undefined LevelsPreset # Sample AMX Lighting controller and internal components Lighting Systems OverviewControl Curves and Low-End Settings Programming CommandsLevels Default Low-endDefault Ramp Time Default Ramp TimeProtocol Conventions AMX Lighting Channel CommandsChannels SENDSTRINGsRamp Dimmers Down Ramp Dimmers UpRamp Dimmers Down Ramp Dimmers UpRamp Active Preset Down Ramp Active Preset UpStop Ramping Dimmer Level Status Stop Ramping PresetRecall Preset Record PresetLow End Status Set CurveCurve Status Set Low EndDimmer Status RebootSet Default Level Time Set Default Preset TimeRamp To Level Set Default Ramp TimeUndefine Dimmer Factory Default Phase QueryVersion Query Ramp Preset Up SENDCOMMANDsRamp Preset Up NEW Sendcommand Protocol ConventionsStop Ramping Preset NEW Ramp Preset Down NEWRamp Preset Down Low End Status NEW Reboot NEWCurve Status NEW Set Low End NEWUndefine Dimmer NEW Sendcommand Radia,?Y Phase Query NEWAppendix a AMX Lighting Curves Basic dimming curve Curves Curve ConfigurationCurves Load Type Curves Standard Dimming CurveCurve 1 Voltage Output in 240V AC Economical Dimming Curve Curve 1 with Low End Setting @ 5%, 10%, and 20% Volts RMSCurve 2 at 240 VAC 10VDC CurveCurve 3 at 120 VAC Curve 4 Voltage output in Volts RMS 12VDC CurveCurve 4 Voltage output in volts DC Lutron FDB CurveCurve 5 at 240 VAC Curve 6 Voltage output in Volts RMS Advance Mark VII CurveCurve 6 Voltage output in volts DC 12% Roll OffCurve 7 Voltage output in Volts RMS Curve 8 at 120 VAC 19% Roll OffCurve 8 Voltage output in volts DC 33% Roll OffCurve 9 Voltage output in Volts RMS Curve a at 120 VAC Curve #1 aCurve a Voltage output in volts DC Log-Curve #1 BCurve B Voltage output in Volts RMS Curve C at 120 VAC Log-Curve #2 CCurve C Voltage output in Volts DC Curve #2 DCurve D Voltage output in Volts RMS 10% Off Curve NCurve N at 240 VAC Always OFF Curve OCurve O at 240 VAC Always on Curve FCurve F at 240 VAC Curve R at 120 VAC Curves 5 & B on the Radia Eclipse RE-DM6 at 120 VAC Curves a & D at 120 VAC Page Testing procedures for AMX Lighting features Software IssuesUsing Pass mode Testing AMX Lighting featuresTo check this Hardware IssuesTroubleshooting hardware Hardware ChecklistPage Increase Your Revenue through education + knowledge
Related manuals
Manual 2 pages 38.75 Kb Manual 2 pages 7.17 Kb

RE-DM4, RE-DM6 specifications

The AMX RE-DM4 is a cutting-edge solution in the realm of digital media management, designed to cater to the complexities of modern broadcasting environments. This advanced device aims to streamline workflows, enhance media asset management, and ensure optimal media delivery across various platforms.

One of the standout features of the AMX RE-DM4 is its robust interface, which allows users to interact with the system intuitively. The device incorporates a user-friendly GUI that enables operators to manage media assets effortlessly. The interface supports drag-and-drop functionalities, which greatly simplifies the process of uploading, organizing, and retrieving digital content.

The AMX RE-DM4 also boasts innovative multimedia processing capabilities, allowing it to handle high-resolution video formats with ease. The device supports a range of codecs, ensuring compatibility with the latest video and audio standards. This versatility is crucial for broadcasters who frequently work with diverse media types and formats.

Furthermore, the AMX RE-DM4 features advanced metadata tagging and search functionalities. This technology empowers users to tag media assets with critical information, enabling quick retrieval and efficient categorization. The integrated search engine is designed to facilitate instant searches, thereby reducing downtime and improving overall productivity.

Another notable characteristic of the AMX RE-DM4 is its scalability. The system is designed to grow alongside evolving media requirements, making it an ideal choice for both small studios and large broadcasting networks. With modular components and expandable storage options, users can easily upgrade their systems as their needs change.

In terms of connectivity, the AMX RE-DM4 includes multiple input and output options, ensuring seamless integration with existing studio equipment and networks. It supports various protocols, which enhances compatibility with other devices and allows for more fluid media workflows.

Security is a crucial aspect of digital media management, and the AMX RE-DM4 addresses this by incorporating robust encryption and access control features. Users can set permissions for different team members, safeguarding sensitive content while still allowing collaborative work environments.

In conclusion, the AMX RE-DM4 emerges as a powerful tool for media professionals, integrating state-of-the-art technologies and features that enhance efficiency and productivity. Its intuitive interface, multimedia processing capabilities, advanced search options, scalability, and robust security measures make it a valuable asset in the fast-paced world of digital media management. This device exemplifies a forward-thinking approach to media handling, positioning itself as a leader in the industry.
Top Page Image Contents