AMX RE-DM4, RE-DM6 manual Log-Curve #2 C, Curve C at 120 VAC

Page 77

Appendix A: AMX Lighting Curves

Log-Curve #2 (C)

FIG. 82 Curve C at 120 VAC

FIG. 83 Curve C at 240 VAC

FIG. 84 shows the output voltage of a dimmer. This curve starts at the low end at about 20 volts and gently rises to only 113 volts. This curve reduces dimming range by about 20%.

 Relay turn on level = 1%

Dimming Range = 20 - 115 VAC.

FIG. 84 Curve C Voltage output in Volts RMS

RE-DM4 and RE-DM6 RADIA Eclipse Dimmer Modules

69

 

 

Page 76 Page 78
Image 77
Page 76 Page 78
Contents Radia Eclipse Dimmer Modules AMX Limited Warranty and Disclaimer Page Page Table of Contents Radia Lighting System Configuration Pages Initial Level Status Reporting Appendix a AMX Lighting Curves Radia Eclipse RE-DM4 Dimmer Module OverviewRE-DM4 Specifications RE-DM4 SpecificationsDimmed Switched Suggested LoadsLine-In Connections RE-DM4 4-pin module connector maleLighting Application for the RE-DM4, Example a RE-DM4 Lighting Application DrawingsRE-DM6 6-channel Integrated Dimmer Module Radia Eclipse RE-DM6 Dimmer ModuleRE-DM6 Specifications RE-DM6 SpecificationsSuggested Installation Loads Line-In Connections for the RE-DM6 Lighting Application for the RE-DM6, Method a RE-DM6 Lighting Application DrawingsApplications FeaturesAMX Lighting Control Equipment AMX Lighting Control EquipmentDimmer modules Dimmer AccessoriesIntegrated dimmer control modules Space Requirements Wiring ConsiderationsPower considerations Knockout locations RDA-ENC2 used as example ConduitRDA-ENC6B and RDA-ENC12B enclosures and dimensions RDA Enclosure DimensionsRDA-ENC2, -ENC4, and -ENC6 enclosure and dimensions Distance a to B Mounting AMX Lighting EnclosuresHigh-Voltage Connections Connecting High-Voltage, Single-Phase Input Power and LoadsConnecting High-Voltage Input Power and Loads RDA-ENC6B 120 VAC Single Phase Line InputRDA-ENC6B 120/240 VAC Line Input Single Phase RDA-ENC6B 120/208 VAC three-phase 4 W + G wiring diagram RDA-ENC6B 120/208 VAC line input three phaseRDC-PFC Power Distribution And Line Input References RDA-ENC6B Three Phase Line Input Connector ReferenceEnclosure module mounting slots and mounting screw holes Installing RDM Modules Into an RDA EnclosureModule Connections Green LED Status IndicatorLow-Voltage Connections Configuring and connecting multiple controllers Red LED Status Indicators RE-DM4 onlyValue Configuring and Connecting AxLinkSW1 DIP Switch Setting Values for AxLink Connecting Dry Closures External powerDry Closures Failsafe InputDefault Low-End Settings Default SettingsDefault preset time values Default PresetsLighting System Link Radia Lighting System Configuration PagesMain Lighting System Radia Configuration ManagerDevice Configuration Device ConfigurationPresets section Preset Configuration Radia Lighting System Configuration Pages Software AMX Radia Lighting ProgrammingPreset # Presets Defined vs. Undefined LevelsPreset Status Sample AMX Lighting controller and internal components Lighting Systems OverviewControl Curves and Low-End Settings Programming CommandsDefault Ramp Time Default Low-endDefault Ramp Time LevelsChannels AMX Lighting Channel CommandsSENDSTRINGs Protocol ConventionsRamp Dimmers Down Ramp Dimmers UpRamp Dimmers Up Ramp Dimmers DownStop Ramping Dimmer Ramp Active Preset UpRamp Active Preset Down Recall Preset Stop Ramping PresetRecord Preset Level StatusCurve Status Set CurveSet Low End Low End StatusSet Default Level Time RebootSet Default Preset Time Dimmer StatusUndefine Dimmer Set Default Ramp TimeRamp To Level Version Query Phase QueryFactory Default Ramp Preset Up NEW SENDCOMMANDsSendcommand Protocol Conventions Ramp Preset UpRamp Preset Down Ramp Preset Down NEWStop Ramping Preset NEW Curve Status NEW Reboot NEWSet Low End NEW Low End Status NEWUndefine Dimmer NEW Sendcommand Radia,?Y Phase Query NEWAppendix a AMX Lighting Curves Basic dimming curve Curves Curve ConfigurationCurves Load Type Curves Standard Dimming CurveCurve 1 Voltage Output in 240V AC Economical Dimming Curve Curve 1 with Low End Setting @ 5%, 10%, and 20% Volts RMSCurve 2 at 240 VAC 10VDC CurveCurve 3 at 120 VAC Curve 4 Voltage output in Volts RMS 12VDC CurveCurve 4 Voltage output in volts DC Lutron FDB CurveCurve 5 at 240 VAC Curve 6 Voltage output in Volts RMS Advance Mark VII CurveCurve 6 Voltage output in volts DC 12% Roll OffCurve 7 Voltage output in Volts RMS Curve 8 at 120 VAC 19% Roll OffCurve 8 Voltage output in volts DC 33% Roll OffCurve 9 Voltage output in Volts RMS Curve a at 120 VAC Curve #1 aCurve a Voltage output in volts DC Log-Curve #1 BCurve B Voltage output in Volts RMS Curve C at 120 VAC Log-Curve #2 CCurve C Voltage output in Volts DC Curve #2 DCurve D Voltage output in Volts RMS 10% Off Curve NCurve N at 240 VAC Always OFF Curve OCurve O at 240 VAC Always on Curve FCurve F at 240 VAC Curve R at 120 VAC Curves 5 & B on the Radia Eclipse RE-DM6 at 120 VAC Curves a & D at 120 VAC Page Using Pass mode Software IssuesTesting AMX Lighting features Testing procedures for AMX Lighting featuresTroubleshooting hardware Hardware IssuesHardware Checklist To check thisPage Increase Your Revenue through education + knowledge
Related manuals
Manual 2 pages 38.75 Kb Manual 2 pages 7.17 Kb

RE-DM4, RE-DM6 specifications

The AMX RE-DM4 is a cutting-edge solution in the realm of digital media management, designed to cater to the complexities of modern broadcasting environments. This advanced device aims to streamline workflows, enhance media asset management, and ensure optimal media delivery across various platforms.

One of the standout features of the AMX RE-DM4 is its robust interface, which allows users to interact with the system intuitively. The device incorporates a user-friendly GUI that enables operators to manage media assets effortlessly. The interface supports drag-and-drop functionalities, which greatly simplifies the process of uploading, organizing, and retrieving digital content.

The AMX RE-DM4 also boasts innovative multimedia processing capabilities, allowing it to handle high-resolution video formats with ease. The device supports a range of codecs, ensuring compatibility with the latest video and audio standards. This versatility is crucial for broadcasters who frequently work with diverse media types and formats.

Furthermore, the AMX RE-DM4 features advanced metadata tagging and search functionalities. This technology empowers users to tag media assets with critical information, enabling quick retrieval and efficient categorization. The integrated search engine is designed to facilitate instant searches, thereby reducing downtime and improving overall productivity.

Another notable characteristic of the AMX RE-DM4 is its scalability. The system is designed to grow alongside evolving media requirements, making it an ideal choice for both small studios and large broadcasting networks. With modular components and expandable storage options, users can easily upgrade their systems as their needs change.

In terms of connectivity, the AMX RE-DM4 includes multiple input and output options, ensuring seamless integration with existing studio equipment and networks. It supports various protocols, which enhances compatibility with other devices and allows for more fluid media workflows.

Security is a crucial aspect of digital media management, and the AMX RE-DM4 addresses this by incorporating robust encryption and access control features. Users can set permissions for different team members, safeguarding sensitive content while still allowing collaborative work environments.

In conclusion, the AMX RE-DM4 emerges as a powerful tool for media professionals, integrating state-of-the-art technologies and features that enhance efficiency and productivity. Its intuitive interface, multimedia processing capabilities, advanced search options, scalability, and robust security measures make it a valuable asset in the fast-paced world of digital media management. This device exemplifies a forward-thinking approach to media handling, positioning itself as a leader in the industry.
Top Page Image Contents